How to Guide

ManualsBrandsRust-Oleum ManualsSpray Paint209562

AEROSOLS TECHNICAL DATA RO-81

V2100 SYSTEM

HAMMERED AERSOL

Form: GDH-1139

Rev.: 042016

.DESCRIPTION AND USES .

Rust-Oleum

High Performance Hammered aerosols

produce a hammered texture finish. Ideal for hiding

surface imperfections, small dents and scratches. Can be

applied directly to metal or over a primer to optimize

corrosion protection. Not for use on galvanized steel.

This product complies with USDA FSIS regulatory sanitation

performance standards for food establishment facilities. This

coating is impervious to moisture and easily cleaned and

sanitized.

.PRODUCTS .

SKU Description

209562 Metal Silver

209563 Metal Gold

209564 Metal Dark Bronze

209590 Metal Black

PACKAGING .

Aerosol containers, 15 oz net weight

COMPANION PRODUCTS .

SKU Description

209566 White Clean Metal Primer

V2169838 Red Primer

V2182838 Gray Primer

.PRODUCT APPLICATION .

SURFACE PRERARATION

ALL SURFACES: Remove all dirt, grease, oil, salt and

chemical contaminants by washing the surface with Pure

Strength Cleaner/Degreaser item #3599402 or other

suitable cleaner. Mold and mildew must be cleaned with a

chlorinated cleaner or bleach solution. Rinse with fresh

water and allow to dry.

STEEL: Hand tool (SSPC-SP-2) or power tool (SSPC-SP-

3) clean to remove loose rust, mill scale, and deteriorated

previous coatings.

PREVIOUSLY COATED: Previously coated surfaces must

be sound and in good condition. Smooth, hard, or glossy

finishes should be scarified by sanding to create a surface

profile. Removal of old paint by sanding, scraping or other

means may generate dust or fumes that contain lead.

APPLICATION

Use when temperature is above 50°F (10°C) and humidity

is below 85% to ensure proper drying. Surface

temperature must be between 50-100°F (10-38°C). Use

primer on bare or rusted surfaces. Protect surrounding

surfaces from overspray. Overspray can carry a significant

distance. Shake can for one minute after mixing ball is

heard. Hold can 10-14 inches from surface. Apply several

light coats a few minutes apart to avoid drips and runs.

DRY AND RECOAT TIMES

Dry times are based on 70°F (21°C) and 50% relative

humidity. Allow more time in cooler temperatures. Dries

tack free in 10-20 minutes and to handle in 1-2 hours.

Recoat within 1 hour or after 24 hours. Two coats may be

needed on rusted metal.

CLEAN UP

Clean valve by turning can upside down and spray for 5

seconds. Some paint will spray out. If clogged, remove tip

and clean in thinner. Do not insert any object into can

valve opening.

Summary of content (2 pages)

PAGE 1
AEROSOLS TECHNICAL DATA RO-81 V2100 SYSTEM HAMMERED AERSOL .DESCRIPTION AND USES . .PRODUCT APPLICATION Rust-Oleum® High Performance Hammered aerosols produce a hammered texture finish. Ideal for hiding surface imperfections, small dents and scratches. Can be applied directly to metal or over a primer to optimize corrosion protection. Not for use on galvanized steel.
PAGE 2
TECHNICAL DATA V2100 SYSTEM HAMMERED AERSOL PHYSICAL PROPERTIES . HAMMERED AEROSOLS Resin Type Modified Alkyd Pigment Type Varies Solvents Acetone, Toluene, Xylene MIR Max value of 1.4 Fill Weight 15 oz. Recommended Dry Film Thickness (DFT) Per Coat 1-2 mils (25-50µ) Practical Coverage at Recommended DFT Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity Approximately 14 sq.ft./can (1.