How to Guide

TECHNICAL DATA PRO-02
PROFESSIONAL
DTM ALKYD ENAMEL (450 VOC)
Form: GDH-762
Rev.: 040715
1
.DESCRIPTION AND USES .
Rust-Oleum
®
Professional DTM Alkyd Enamels are oil-
modified alkyds with excellent rust prevention when
applied directly to metal. They also offer excellent
coverage, chip resistance and color retention. Not for use
on galvanized steel.
.
PRODUCTS
.
SKU Description
PRIMERS (Gallons)
7769402 Rusty Metal Primer
7780402 White Clean Metal Primer
8781402 Aluminum Primer
FINISHES (Gallons)
7715402 Aluminum
7524402 Safety Blue
7727402 Royal Blue
7738402 Hunter Green
7543402 Safety Yellow
7748402 Dark Brown
7555402 Safety Orange
7564402 Safety Red
7765402 Regal Red
7770402 Almond
7771402 Sand
7775402 Leather Brown
7776402 Flat Black
7779402 Black
7781402 Light Machine Gray
7786402 Smoke Gray
7790402 Flat White
7792402 White
239076 Semi-Gloss White
239078 Semi-Gloss Black
FINISHES (Quarts)
V7727502 Royal Blue
V7738502 Hunter Green
V7570502 Almond
V7575502 Leather Brown
V7579502 Gloss Black
7578502 Flat Black
V7586502 Smoke Gray
7590502 Flat White
V7592502 Gloss White
202191T Safety Yellow
202192T Safety Red
243995L Semi-Gloss Black
243996T Semi-Gloss White
.
PRODUCT APPLICATION
.
PAINTING CONDITIONS
Apply only when air and surface temperatures are
between 32-90ºF (0-38ºC) and humidity is below 85% to
ensure proper drying. Do not apply to surfaces that, when
heated, exceed 200ºF (93ºC) or galvanized metal.
Professional DTM Alkyd Enamels can be used over most
latex or oil paints. Professional DTM Alkyd Enamels and
Primers are not recommended for water immersion.
SURFACE PREPARATION
Clean surface with soap and water, rinse and let dry.
Remove loose paint and rust with a wire brush or
sandpaper. Lightly sand glossy surfaces.
WARNING! If you scrape, sand, or remove old paint, you
my release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
APPLICATION
Mix thoroughly to ensure any settled pigment is re-
dispersed before using. Thin material, only if necessary,
with acetone. For brush or roller, thinning is not normally
required. For air spray, thin up to 1-½ to 2 pints per gallon.
Do not thin with gasoline, lacquer thinner, turpentine, etc.
For airless spray, thinning is not normally required. Apply
with a good quality brush, roller or spray gun.
Brush: Use light, even strokes Excessive brushing
reduces film thickness and protection.
Roller: The rougher the surface, the longer the roller nap
should be. Cover approximately one square yard at a time.
Roll away from previously coated area and work back o it
for a uniform appearance. Use a brush on crevices and
sharp edges.
Spray Gun: Follow spray gun directions carefully. Always
keep the gun ten to twelve inches from the surface and in
motion while spraying.
DRY & RECOAT TIMES
Dry and recoat times are based on 70°F (21°C) and 50%
relative humidity. Allow more time at cooler temperatures.
Dries to the touch in 2-4 hours, to handle in 5-10 hours
and is fully dry after 24 hours. Recoat after 24 hours.
CLEAN-UP
Clean brush, roller and other tools with mineral spirits.