Technical Specifications

TECHNICAL DATA
PTX-02
PAINTER’S TOUCH
®
ULTRA COVER 2X ENAMEL BRUSH
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
Phone: 877∙385∙8155
www.rustoleum.com
Form: GDH-504
Rev.: 073119
PHYSICAL PROPERTIES
GLOSS
SATIN
FLAT
SOLVENT
METALLIC
Resin Type
Water-based Acrylic
Water-based Acrylic
Water-based Acrylic
Oil-based Alkyd
Pigment Type
Varies with Color
Varies with Color
Varies with Color
Leafing Aluminum.
Gold Metallic
Solvents
Water, Glycol Ethers
Water, Glycol Ethers
Water, Glycol Ethers
Aromatic
Hydrocarbons,
Xylene
Weight
Per Gallon
8.6-11.8 lbs.
9.0-10.2 lbs.
9.8-11.8 lbs.
7.6-8.5 lbs.
Per Liter
1.03-1.41 kg
1.08-1.22 kg
1.17-1.41 kg
0.91-1.02 kg
Solids
By Weight
33.2-58.3%
32.3-42.8%
43.0-58.3%
45.7-60.2%
By Volume
31.0-41.1%
26.6-30.1%
32.6-41.1%
36.3-48.6%
Volatile Organic Compounds
<200 g/l
(1.67 lbs/gal)
<180 g/l
(1.50 lbs/gal)
<190 g/l
(1.70 lbs./gal.
<500 g/l
(4.20 lbs./gal.)
Recommended Dry Film
Thickness (DFT) per Coat
1.5-2.5 mils
(37.5-62.5µ)
1.5-2.5 mils
(37.5-62.5µ)
1.5-2.5 mils
(37.5-62.5µ)
1.0-1.5 mils
(25-37.5µ)
Wet Film to Achieve DFT
(unthinned material)
5.0-6.0 mils
(125-150µ)
5.0-6.0 mils
(125-150µ)
3.5-7.5 mils
(125-150µ)
5.0-6.0 mils
(125-150µ)
Practical Coverage at
Recommended DFT (assumes
15% material loss)
40-90 sq.ft./qt.
(1.0-2.2 m
2
/l)
35-70 sq.ft./qt.
(0.8-1.7 m
2
/l)
40-90 sq.ft./qt.
(1.0-2.2 m
2
/l)
50-110 sq.ft./qt.
(1.2-2.7 m
2
/l)
Dry Times at 70-
80°F (21-27°C)
and 50% Relative
Humidity
Touch
30 minutes
30 minutes
30 minutes
2-4 hours
Handle
1 hour
1 hour
1 hour
5-9 hours
Recoat
2-4 hours
2-4 hours
2-4 hours
After 24 hours
Dry Heat Resistance
200ºF (93ºC)
200ºF (93ºC)
200ºF (93ºC)
200ºF (93ºC)
Shelf Life
5 years
5 years
5 years
5 years
Flash Point
>200°F (93°C)
>150°F (66°C)
>150°F (66°C)
80°F (27°C)
Safety Information
For additional information, see SDS
Calculated values are shown and may vary from the actual manufactured material.
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.