SDS

Date Printed: 5/15/2015
Methyl Ethyl Ketone 78-93-3 15.0 200 ppm 300 ppm 200 ppm N.E.
n-Butane 106-97-8 10.0 1000 ppm 1000 ppm N.E. N.E.
Titanium Dioxide 13463-67-7 10.0
10 mg/m3 (Total
Dust)
N.E.
15 mg/m3 [Total
Dust]
N.E.
Butyl Benzyl Phthalate 85-68-7 5.0 N.E. N.E. N.E. N.E.
Ethylene Glycol Monobutyl Ether 111-76-2 5.0 20 ppm N.E. 50 ppm N.E.
Xylene (mixed isomers) 1330-20-7 5.0 100 ppm 150 ppm 100 ppm N.E.
Ethylbenzene 100-41-4 1.0 20 ppm 125 ppm 100 ppm N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Use explosion-proof ventilation equipment. Prevent build-up of vapors by opening all
doors and windows to achieve cross-ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must
be followed whenever workplace conditions warrant a respirator's use. A NIOSH/MSHA approved air purifying respirator with an
organic vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to
exceed exposure limits.
Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any potential for
an uncontrolled release, exposure levels are not known, or in any other circumstances where air purifying respirators may not
provide adequate protection.
SKIN PROTECTION: Use impervious gloves to prevent skin contact and absorption of this material through the skin. Nitrile or
Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further information regarding personal
protective equipment and its application.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking.
9. Physical and Chemical Properties
Appearance:
Aerosolized Mist
Physical State:
Liquid
Odor:
Solvent Like
Odor Threshold:
N.E.
Relative Density:
0.764
pH:
N.A.
Freeze Point, °C:
N.D.
Viscosity:
N.D.
Solubility in Water:
Miscible
Partition Coefficient, n-
octanol/water:
No Information
Decompostion Temp., °C:
No Information
Boiling Range, °C:
-34 - 464
Explosive Limits, vol%:
1.0 - 12.8
Flammability:
Does not Support Combustion
Flash Point, °C:
No Information
Evaporation Rate:
Faster than Ether
Auto-ignition Temp., °C:
No Information
Vapor Density:
Heavier than Air
Vapor Pressure:
N.D.
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid temperatures above 120 ° F. Avoid all possible sources of ignition.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies.
HAZARDOUS DECOMPOSITION: Contains solvents which may form carbon monoxide, carbon dioxide, and formaldehyde. By
open flame, carbon monoxide and carbon dioxide. When heated to decomposition, it emits acrid smoke and irritating fumes.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: May form peroxides of unkown stability. This product is stable under normal storage conditions.
11. Toxicological information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Causes eye irritation.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Substance may cause slight skin irritation. Prolonged or repeated contact
may cause skin irritation.
EFFECTS OF OVEREXPOSURE - INHALATION: Harmful if inhaled. High gas, vapor, mist or dust concentrations may be harmful
if inhaled. Avoid breathing fumes, spray, vapors, or mist. High vapor concentrations are irritating to the eyes, nose, throat and
lungs.
Page 3 / 6