SDS

ManualsBrandsRust-Oleum Transformations ManualsAppliance, Tub & Tile Paint46 oz. White Interior Tile Finish Kit

Date Printed: 8/13/2012

4. First-aid Measures4. First-aid Measures

FIRST AID FIRST AID

EYE CONTACT: EYE CONTACT:

Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical

attention. Do NOT allow rubbing of eyes or keeping eyes closed.

FIRST AID FIRST AID

SKIN CONTACT: SKIN CONTACT:

Wash with soap and water. Get medical attention if irritation develops or persists.

FIRST AID FIRST AID

INHALATION: INHALATION:

Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get

immediate medical attention. Do NOT use mouth-to-mouth resuscitation.

FIRST AID FIRST AID

INGESTION: INGESTION:

If swallowed, do not induce vomiting. If victim is conscious and alert, give 2 to 4 cupfuls of water or milk.

Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person. Treat

symptomatically and supportively. Aspiration hazard: Do not induce vomiting or give anything by mouth because this material can

enter the lungs and cause severe lung damage. Get immediate medical attention.

5. Fire-fighting Measures5. Fire-fighting Measures

Flash Point, °F 52 (Setaflash)

EXTINGUISHING MEDIA: Alcohol Foam, Carbon Dioxide, Dry Chemical, Foam, Water Fog

UNUSUAL FIRE AND EXPLOSION HAZARDS: Combustible liquid and vapor. Vapors may form explosive mixtures with air.

Vapors can travel to a source of ignition and flash back. Isolate from heat, electrical equipment, sparks and open flame.

SPECIAL FIREFIGHTING PROCEDURES: Water may be used to cool closed containers to prevent pressure buildup and possible

autoignition or explosion. Full protective equipment including self-contained breathing apparatus should be used. Evacuate area

and fight fire from a safe distance.

6. Accidental Release Measures

STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Isolate the hazard area and deny entry to unnecessary and

unprotected personnel. Remove all sources of ignition, ventilate area and remove with inert absorbent and non-sparking tools.

Dispose of according to local, state (provincial) and federal regulations. Do not incinerate closed containers. Contain spilled liquid

with sand or earth. DO NOT use combustible materials such as sawdust. Eliminate all ignition sources; use explosion-proof

equipment. Place material in a container and dispose of according to local, provincial, state and federal regulations.

7. Handling and Storage

HANDLING: Wash thoroughly after handling. Use only in a well-ventilated area. Follow all MSDS/label precautions even after

container is emptied because it may retain product residues. Avoid breathing fumes, vapors, or mist. Avoid prolonged or repeated

contact with skin. Wash hands before eating. Use only with adequate ventilation.

STORAGE: Keep containers tightly closed. Isolate from heat, electrical equipment, sparks and open flame. Do not store above

120 ° F. Store large quantities in buildings designed and protected for storage of NFPA Class II combustible liquids. Keep away

from heat, sparks, flame and sources of ignition. Keep container closed when not in use.

8. Exposure Controls/Personal Protection

ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne

levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-

ventilation.

RESPIRATORY PROTECTION: A NIOSH/MSHA approved air purifying respirator with an organic vapor cartridge or canister may

be permissible under certain circumstances where airborne concentrations are expected to exceed exposure limits.

Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any potential for an

uncontrolled release, exposure levels are not known, or in any other circumstances where air purifying respirators may not provide

adequate protection. A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be followed

whenever workplace conditions warrant a respirator's use.

Page 2 / 5