Use and Care Manual

TECHNICAL DATA
COUNTERTOP TRANSFORMATIONS
TM
Rust-Oleum Corporation Form: GDH-64
11 Hawthorn Parkway Phone: 877•385•8155 Rev.: 052013
Vernon Hills, Illinois 60061 www.rustoleum.com
An RPM Company
.PHYSICAL PROPERTIES .
BASE COAT
WETTING AGENT
TOP COAT
Resin Type
Acrylic
Surfactant
Modified silicone epoxy
Pigment Type
Various
n/a
Clear
Solvents
Water
Water
n/a
Weight
Per Gallon
8.6-9.1 lbs.
8.4 lbs.
9.0 lbs.
Per Liter
1.0-1.1 kg
1.0 kg
1.0 kg
Solids
By Weight
33.5-36.0%
1.5%
98%
By Volume
30.0-33.0%
1.0%
97%
Volatile Organic Compounds
(activated material)
<250 g/l (2.08 lbs./gal.)
<250 g/l (2.08 lbs./gal.)
<250 g/l (2.08 lbs./gal.)
Recommended Dry Film
(DFT) Per Coat
2.0-2.5 mils (50-62.5µ)
n/a
4.0-8.0 mils (100-200µ)
Wet Film to Achieve DFT (unthinned
material)
6.0-7.5 mils (150-187.5µ)
n/a
4.0-8.0 mils (100-200µ)
Theoretical Coverage at
1 mil DFT (25µ)
480-530 sq. ft./gal.
(11.8-13.0 m
2
/l)
n/a
1,550 sq. ft./gal.
(38 m
2
/l)
Practical Coverage at Recommended
DFT (assumes 15% material loss)
160-200 sq. ft./gal.
(3.9-4.7 m
2
/l)
n/a
165-330 sq. ft./gal.
(4.0-8.1 m
2
/l)
Dry Times at 70-80°F
(21-27°C) and 50%
rel. hum.
Touch
Minimum 12 hours
n/a
n/a
Recoat
n/a
n/a
4-8 hours
Stain Sealing
n/a
n/a
2 days
Full
Hardness
n/a
n/a
7-10 days
Dry Heat Resistance
200°F (93°C)
n/a
200°F (93°C)
Shelf Life
2 years
n/a
2 years
Flash Point
>210°F (99°C)
n/a
>160°F (67°C)
Safety Information
COMBUSTIBLE LIQUID AND VAPOR. HARMFUL IF INHALED. MAY AFFECT
BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA.
CAUSES RESPIRATORY TRACT, EYE AND SKIN IRRITATION. FOR
INDUSTRIAL OR COMMERCIAL USE ONLY. KEEP OUT OF REACH OF
CHILDREN.SEE THE PRODUCT MATERIAL SAFETY DATA SHEET (MSDS)
AND LABEL WARNINGS FOR ADDITIONAL SAFETY INFORMATION.
Safety Information
For additional information, see MSDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.