Use and Care Manual

ManualsBrandsRust-Oleum Stops Rust ManualsPaint12 oz. Protective Enamel Gloss Sunrise Red Spray Paint (Case of 6)

TECHNICAL DATA SRT-01

STOPS RUST

ENAMEL SPRAYS

Form: CS2201

Rev.: 090313

.DESCRIPTION AND USES .

Rust-Oleum

Stops Rust

Enamel Sprays are designed to

provide a durable protective coating with excellent rust

prevention, and excellent resistance to abrasion, fading, chipping,

and dulling. These sprays apply easily, provide excellent

coverage and dry fast to a tough attractive finish. Rust-Oleum

Stops Rust

Enamel Sprays are ideal for ferrous, non-ferrous

metal and wood surfaces. It features a comfort tip with a wider

finger pad to reduce fatigue caused by continuous spraying and

an any-angle tip which allows you to spray at any angle. Not for

use on galvanized metal.

.PRODUCTS .

SKU Description SKU Description

7701830 Crystal Clear 7792830 Gloss White

7721830 Fresh Blue 7794830 Antique White

7722830 Harbor Blue 7797830 Semi-Gloss White

7723830 Navy 7798830 Semi-Gloss Black

7724830 Sail Blue 214084 Orange

7727830 Royal Blue 214085 Flat Brown

7731830 Grass Green 214086 Charleston Green

7733830 Dark Hunter Green 214087 Army Green

7738830 Hunter Green 241235 Pistachio

7747830 Sunburst Yellow 241236 Glacier Blue

7754830 Anodized Bronze 245897 Burnt Orange

7762830 Sunrise Red 248567 Merlot

7763830 Carnival Red 248568 Cherry

7765830 Regal Red 248569 Emerald

7768830 Burgundy 248630 French Roast

7770830 Almond 248631 Night Tide

7771830 Sand 249032 Khaki

7775830 Leather Brown 250702 Pure White

7776830 Flat Black 250703 Cobblestone

7779830 Gloss Black 250704 Lobster Red

7783830 Pewter Gray 250705 Fern

7784830 Charcoal Gray 262661 Dark Walnut

7786830 Smoke Gray 267112 Kona Brown

7789830 Canvas White 269292 Maui Blue

7790830 Flat White

.PAINTING CONDITIONS .

Use outdoors or in a well ventilated area such as an open

garage. Apply when temperature is between 50-90°F (10-

32°C) and humidity is below 65% to ensure proper drying.

Do not apply to surfaces, when heated, exceed 200°F

(93°C). Do not apply to galvanized steel. Avoid spraying in

very windy and dusty conditions. Cover surrounding area

to protect from spray mist.

..PRODUCT APPLICATION .

SURFACE PREPARATION

Remove all dirt, grease, oil, salt and chemical

contaminants by washing the surface with a commercial

detergent, or other suitable cleaning method. Rinse with

fresh water and allow to thoroughly dry. Remove loose

paint and rust with a wire brush or sandpaper. Previously

coated surfaces must be sound and in good condition.

Smooth, hard, or glossy finishes should be scarified by

sanding to create a surface profile. . WARNING! If you

scrape, sand or remove old paint from any surface, you

may release lead paint dust. LEAD IS TOXIC.

EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS

ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN

CHILDREN. PREGNANT WOMEN SHOULD ALSO

AVOID EXPOSURE. Wear a NIOSH approved respirator

to control lead exposure. Clean up carefully with a HEPA

vacuum and a wet mop. Before you start, find out how to

protect yourself and your family by contacting the National

Lead Information Hotline at 1-800-424-LEAD or log on to

www.epa.gov/lead.

PRIMING

Use of a Rust-Oleum

primer provides added corrosion

protection, excellent adhesion and hiding and is especially

recommended for bare wood and metal. The following

primers are recommended.

7769 Rusty Metal Primer

7780 Clean Metal Primer

2081 Light Gray Auto Primer

2067 Red Auto Primer

2089 Dark Gray Auto Primer

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA SRT-01 STOPS RUST ENAMEL SPRAYS .DESCRIPTION AND USES .PAINTING CONDITIONS . . Rust-Oleum® Stops Rust® Enamel Sprays are designed to provide a durable protective coating with excellent rust prevention, and excellent resistance to abrasion, fading, chipping, and dulling. These sprays apply easily, provide excellent coverage and dry fast to a tough attractive finish. Rust-Oleum® Stops Rust® Enamel Sprays are ideal for ferrous, non-ferrous metal and wood surfaces.
PAGE 2
TECHNICAL DATA STOPS RUST ENAMEL SPRAYS ..PRODUCT APPLICATION (cont.) . . APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use. Hold can 10-16" from the surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface. Keep the can in motion while spraying.
PAGE 3
TECHNICAL DATA STOPS RUST ENAMEL SPRAYS PHYSICAL PROPERTIES . ENAMEL SPRAY FINISHES Resin Type Oil modified alkyd Pigment Type Varies with color Xylene, Aliphatic Hydrocarbons MIR Fill Weight 1.4 Max Solvents 12 ounces Recommended Dry Film Thickness (DFT) Per Coat 1.0-2.0 mils (25-50µ) Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70°F (21°C) and 50% Relative Humidity 10-12 sq.ft./can (0.9-1.