Use and Care Manual

TECHNICAL DATA
SRT-59
STOPS RUST
®
CUSTOM SPRAY 5-IN-1 CLEARS
1
Form: ARJ-2529
Rev.: 110122
DESCRIPTION AND USES
Rust-Oleum
®
Stops Rust
®
Custom Spray 5-in-1 allows you to
choose between 5 different spray patterns for ultimate
control and confidence over your next project. Stops Rust
Clear Protective Enamel is the ultimate standard in rust
protection and durability while providing an ultra glossy or
matte finish. The advanced Stops Rust Clear Enamel
formula provide 30% greater protection when compared to
original matching Stops Rust Clear Enamels with standard
tip based on ASTM tests for adhesion over steel (ASTM
D3359), Mandrel Bend/flexibility (ASTM D522) and impact
resistance (ASTM D2794). The advanced Stops Rust Clear
Enamel formula also provide 30% greater color retention
when compared to original matching Stops Rust Clear
Enamels with standard tip (ASTM D2244).
PRODUCTS
SKU
DESCRIPTION (12 oz. Aerosol)
376868
Matte Clear
376883
Satin Clear
376885
Gloss Clear
PRODUCT APPLICATION
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants
by washing the surface with a commercial detergent, or
other suitable cleaning method. Rinse with fresh water and
allow to thoroughly dry. Remove loose paint and rust with a
wire brush or sandpaper. Lightly sand glossy surfaces.
Clean with soap and water, rinse and let dry.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and
a wet mop. Before you start, find out how to protect yourself
and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
PRODUCT APPLICATION (cont.)
APPLICATION
Use outdoors or in a well-ventilated area such as an open
garage. Use when temperature is between 50-90°F
(10-32°C) and humidity is below 65% to ensure proper
drying. Do not apply to surfaces that, when heated, exceed
200°F (93°C) or galvanized metal. Avoid spraying in very
windy, dusty conditions. Cover surrounding area to protect
from spray mist.
Before spraying, turn dial to the desired spray pattern and
test on an inconspicuous area or on scrap material. Scan
QR code to learn more. Shake can vigorously for one minute
after mixing ball begins to rattle. If mixing ball fails to rattle,
DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often
during use. Keep the can the same distance from the
surface. Recommended distance from the surface will vary
based on spray selection. Scan QR code on can for details.
Keep the can in motion while spraying. Spray in a steady
back-and-forth motion, slightly overlapping each stroke.
Spray at any angle. Apply 2 or more light coats a few
minutes apart. Turn dial to LOCK position when finished
spraying.
Dial Position
Spray Description
Recommend Spray
Distance
1
High Output
10-14”
2
Standard
8-12”
3
Low Output
3-6”
4
Vertical Fan
8-12”
5
Horizontal Fan
8-12”
DRY AND RECOAT TIMES
Based on 70°F (21°C) 50% relative humidity. Allow more
time at cooler temperatures. Dries to touch in 15 minutes, to
handle in 30 minutes. May recoat anytime. Do not apply
clear over Stops Rust
®
Bright Coat Finish or Aluminum
Finish.
DIAL CARE AND CLOGGING
To prevent clogging, clean face of the dial with mineral
spirits when finished spraying. DO NOT remove cap or dial.
CLEAN UP
To remove wet paint, clean with mineral spirits. Throw away
empty can in trash pickup. Do not burn or place in home
trash compactor.