SDS

Date Printed: 4/9/2019
Ethylbenzene 100-41-4 5.0 20 ppm N.E. 100 ppm N.E.
Octane 111-65-9 5.0 300 ppm N.E. 500 ppm N.E.
n-Heptane 142-82-5 5.0 400 ppm 500 ppm 500 ppm N.E.
Medium Oil Alkyd PROPRIETARY 5.0 N.E. N.E. N.E. N.E.
Carbon Black 1333-86-4 1.0 3 mg/m3 N.E. 3.5 mg/m3 N.E.
Methanol 67-56-1 1.0 200 ppm 250 ppm 200 ppm N.E.
Stoddard Solvent 8052-41-3 1.0 100 ppm N.E. 500 ppm N.E.
bis(1,2,2,6,6-Pentamethyl-4-
Piperidinyl) Sebacate
41556-26-7 1.0 N.E. N.E. N.E. N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Use explosion-proof ventilation equipment. Provide general dilution of local exhaust
ventilation in volume and pattern to keep TLV of hazardous ingredients below acceptable limits. Prevent build-up of vapors by
opening all doors and windows to achieve cross-ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must
be followed whenever workplace conditions warrant a respirator's use. A NIOSH/MSHA approved air purifying respirator with
organic vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to
exceed exposure limits.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin
protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
Engineering Measures for Combustible Dust: No Information
9. Physical and Chemical Properties
Appearance:
Aerosolized Mist
Physical State:
Liquid
Odor:
Solvent Like
Odor Threshold:
N.E.
Relative Density:
0.783
pH:
N.A.
Freeze Point, °C:
N.D.
Viscosity:
N.D.
Solubility in Water:
Slight
Partition Coefficient, n-
octanol/water:
N.D.
Decompostion Temp., °C:
N.D.
Boiling Range, °C:
-37 - 537
Explosive Limits, vol%:
0.9 - 10.7
Flammability:
Supports Combustion
Flash Point, °C:
-96
Evaporation Rate:
Faster than Ether
Auto-ignition Temp., °C:
N.D.
Vapor Density:
Heavier than Air
Vapor Pressure:
N.D.
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid temperatures above 120°F (49°C). Avoid all possible sources of ignition.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies.
HAZARDOUS DECOMPOSITION: By open flame, carbon monoxide and carbon dioxide. When heated to decomposition, it emits
acrid smoke and irritating fumes. Contains solvents which may form carbon monoxide, carbon dioxide, and formaldehyde.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions. May form peroxides of unkown stability.
11. Toxicological Information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Causes Serious Eye Irritation
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: May cause skin irritation. Allergic reactions are possible. May cause skin
sensitization, an allergic reaction, which becomes evident upon re-exposure to this material.
EFFECTS OF OVEREXPOSURE - INHALATION: Harmful if inhaled. High gas, vapor, mist or dust concentrations may be harmful
if inhaled. Avoid breathing fumes, spray, vapors, or mist. High vapor concentrations are irritating to the eyes, nose, throat and
lungs. Prolonged or excessive inhalation may cause respiratory tract irritation.
Page 4 / 7