Use and Care Manual

TECHNICAL DATA
SRT-09
STOPS RUST
®
TEXTURED SPRAYS
1
Form: GDH-729
Rev.: 102021
DESCRIPTION AND USES
Rust-Oleum
®
Stops Rust
®
Textured Sprays are designed to
provide a durable protective coating with excellent resistance
to rust, and excellent resistance to abrasion, fading,
chipping, and dulling. These sprays apply easily, provide
excellent coverage and dry fast to a tough attractive finish.
Rust-Oleum Stops Rust Textured Sprays are ideal for
outdoor metal surfaces. These sprays feature a comfort tip
with a wider finger pad to reduce fatigue caused by
continuous spraying. Not for use on galvanized metal.
PRODUCTS
SKU
DESCRIPTION (Aerosol)
MULTICOLOR TEXTURE
223523
Autumn Brown
223524
Desert Bisque
223525
Aged Iron
223526
Deep Forest
239119
Sea Green
239120
Radiant Brass
239121
Caribbean Sand
239122
Rustic Umber
TEXTURED METALLIC
251053
Silver
252303
Galaxy
252304
Moonlit Copper
262660
Mystic Brown
353030
Midnight Gold
TEXTURED
7220830
Black
7221830
Dark Pewter
7222830
Forest Green
7223830
Sandstone
7225830
White
7226830
Bronze
241255
Dark Brown
PRODUCT APPLICATION
Use outdoors or in a well-ventilated area such as an open
garage. Use when temperature is between 50-90°F
(10-32°C) and humidity is below 70% to ensure proper
drying. Do not apply to surfaces that, when heated, exceed
200°F (93°C) or galvanized metal. Avoid spraying in very
windy, dusty conditions. Cover surrounding area to protect
from spray mist.
PRODUCT APPLICATION (cont.)
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants
by washing the surface with a commercial detergent, or
other suitable cleaning method. Rinse with fresh water and
allow to thoroughly dry. Remove loose paint and rust with a
wire brush or sandpaper. Previously coated surfaces must
be sound and in good condition. Smooth, hard, or glossy
finishes should be scarified by sanding to create a surface
profile.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS,
SUCH AS BRAIN DAMAGE; ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a
NIOSH approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you start, find
out how to protect yourself and your family by contacting the
National Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
PRIMING
Use of a Stops Rust
®
Primer provides added corrosion
protection, superior adhesion and hiding and is especially
recommended for bare wood and metal.
7769830
Rusty Metal Primer
7780830
Clean Metal Primer
APPLICATION
Shake can vigorously for one minute after mixing ball begins
to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN.
Contact Rust-Oleum. Shake often during use. Hold can
upright 18-24" from surface and spray in a steady back-and-
forth motion, slightly overlapping each stroke. Keep the can
the same distance from the surface. Keep the can in motion
while spraying. It is recommended to apply a light first coat,
target 50% coverage. Apply 2 or more light coats a few
minutes apart.
DRY AND RECOAT TIMES
Based on 70°F (21°C) 50% relative humidity. Allow more
time at cooler temperatures. Dries to touch in 15 minutes,
dry to handle in 1-2 hours, and fully dry in 48 hours. Primers
may be top coated immediately. Apply a second coat or
clear coat within 1 hour or after 48 hours.
CLEAN UP
Wipe off tip before storing. Clean up wet paint with Xylene
or mineral spirits. Throw away empty can in trash pickup.
Do not burn or place in home trash compactor.
CLOGGING
If valve clogs, twist and pull off spray tip and rinse it in a
solvent such as mineral spirits. Do not stick a pin or other
objects into the stem.