Use and Care Manual

ManualsBrandsRust-Oleum Stops Rust ManualsPaint12 oz. Protective Enamel Satin Cabernet Spray Paint (Case of 6)

TECHNICAL DATA SRT-03

STOPS RUST

SATIN SPRAYS

Form: CS2155

Rev.: 111813

.DESCRIPTION AND USES .

Rust-Oleum

Stops Rust

Satin Sprays are designed to provide

a durable protective coating with excellent resistance to rust, and

excellent resistance to abrasion, fading, chipping, and dulling.

This classic low sheen finish is ideal for indoor and outdoor

projects. These sprays apply easily, provide excellent coverage

and dry fast to a tough attractive finish. It features a comfort tip

with a wider finger pad to reduce fatigue caused by continuous

spraying and an any-angle tip which allows you to spray at any

angle. Not for use on galvanized metal.

.PRODUCTS .

SKU (12 ounces) Description

7720830 Sage

7728830 Navy Blue

7730830 Teal

7732830 Hunter Green

7737830 Spruce Green

7739830 Charcoal Green

7749830 Dark Hunter Green

7758830 Almond

7760830 Heritage Red

7767830 Redwood

7772830 Putty

7774830 Chestnut Brown

7777830 Black

7791830 White

7793830 Shell White

241237 Dark Olive

241238 Dark Taupe

241239 Dark Brown

241250 Old Brick

241251 Cayenne Red

241252 Lake Blue

248632 American Red

248633 Indigo

248635 Cabernet

250896 Amber

276270 Sapphire

276271 French Beige

..PAINTING CONDITIONS .

Use outdoors or in a well ventilated area such as an open

garage. Use when temperature is between 50-90°F (10-

32°C) and humidity is below 65% to ensure proper drying.

Do not apply to surfaces, when heated, exceed 200°F

(93°C). Do not apply to galvanized steel. Avoid spraying in

very windy and dusty conditions. Cover surrounding area

to protect from spray mist.

..PRODUCT APPLICATION .

SURFACE PREPARATION

Remove all dirt, grease, oil, salt and chemical

contaminants by washing the surface with a commercial

detergent, or other suitable cleaning method. Rinse with

fresh water and allow to thoroughly dry. Remove loose

paint and rust with a wire brush or sandpaper. Previously

coated surfaces must be sound and in good condition.

Smooth, hard, or glossy finishes should be scarified by

sanding to create a surface profile. WARNING! If you

scrape, sand or remove old paint from any surface, you

may release lead paint dust. LEAD IS TOXIC.

EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS

ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN

CHILDREN. PREGNANT WOMEN SHOULD ALSO

AVOID EXPOSURE. Wear a NIOSH approved respirator

to control lead exposure. Clean up carefully with a HEPA

vacuum and a wet mop. Before you start, find out how to

protect yourself and your family by contacting the National

Lead Information Hotline at 1-800-424-LEAD or log on to

www.epa.gov/lead.

PRIMING

Use of a Rust-Oleum

primer provides added corrosion

protection, excellent adhesion and hiding and is especially

recommended for bare wood and metal. The following

primers are recommended.

7769 Rusty Metal Primer

7780 Clean Metal Primer

2081 Light Gray Auto Primer

2067 Red Auto Primer

2089 Dark Gray Auto Primer

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA SRT-03 STOPS RUST SATIN SPRAYS .DESCRIPTION AND USES ® . ..PAINTING CONDITIONS . ® Rust-Oleum Stops Rust Satin Sprays are designed to provide a durable protective coating with excellent resistance to rust, and excellent resistance to abrasion, fading, chipping, and dulling. This classic low sheen finish is ideal for indoor and outdoor projects. These sprays apply easily, provide excellent coverage and dry fast to a tough attractive finish.
PAGE 2
TECHNICAL DATA STOPS RUST SATIN SPRAYS ..PRODUCT APPLICATION (cont.) . . . APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use. Hold can upright 10-16" from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface. Keep the can in motion while spraying.
PAGE 3
TECHNICAL DATA STOPS RUST SATIN SPRAYS PHYSICAL PROPERTIES . SATIN SPRAY FINISHES Resin Type Oil modified alkyd Pigment Type Varies with color MIR 1.4 Max Fill Weight 12 ounces Solvents Aromatic hydrocarbons, Xylene Recommended Dry Film Thickness (DFT) Per Coat 1.0-2.0 mils Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70°F (21°C) and 50% Relative Humidity 10-12 sq. ft./can (0.9-1.