Use and Care Manual

ManualsBrandsRust-Oleum Stops Rust ManualsPaint12 oz. Protective Enamel Rustic Umber Multi-Colored Textured Spray Paint

TECHNICAL DATA SRT-09

STOPS RUST

TEXTURED SPRAYS

Form: CS2166

Rev.: 030113

.DESCRIPTION AND USES .

Rust-Oleum

Stops Rust

Textured Sprays are designed to

provide a durable protective coating with excellent resistance to

rust, and excellent resistance to abrasion, fading, chipping, and

dulling. These sprays apply easily, provide excellent coverage

and dry fast to a tough attractive finish. Rust-Oleum

Stops

Rust

Textured Sprays are ideal for outdoor metal surfaces.

These sprays feature a comfort tip with a wider finger pad to

reduce fatigue caused by continuous spraying and an any-angle

tip which allow s you to spray at any angle. Not for use on

galvanized metal.

.PRODUCTS (12 ounce sprays) .

MULTICOLOR TEXTURE

223523 Autumn Brown

223524 Desert Bisque

223525 Aged Iron

223526 Deep Forest

239119 Sea Green

239120 Radiant Brass

239121 Caribbean Sand

239122 Rustic Umber

TEXTURED METALLIC

251053 Silver

252303 Galaxy

252304 Moonlit Copper

262658 Excalibur

262660 Mystic Brown

TEXTURED

7220830 Black

7221830 Dark Pewter

7222830 Forest Green

7223830 Sandstone

7224830 Nickel

7225830 White

7226830 Bronze

7227830 Rust

7228830 Sage

241253 Dark Olive

241254 Dark Taupe

241255 Dark Brown

241256 Old Brick

..PAINTING CONDITIONS .

Use outdoors or in a well ventilated area such as an open

garage. Apply when temperature is between 50-90°F (10-

32°C) and humidity is below 65% to ensure proper drying.

Do not apply to surfaces, when heated, exceed 200°F

(93°C). Do not apply to galvanized steel. Avoid spraying in

very windy and dusty conditions. Cover surrounding area

to protect from spray mist.

..PRODUCT APPLICATION .

SURFACE PREPARATION

Remove all dirt, grease, oil, salt and chemical

contaminants by washing the surface with a commercial

detergent, or other suitable cleaning method. Rinse with

fresh water and allow to thoroughly dry. Remove loose

paint and rust with a wire brush or sandpaper. Previously

coated surfaces must be sound and in good condition.

Smooth, hard, or glossy finishes should be scarified by

sanding to create a surface profile. WARNING! If you

scrape, sand or remove old paint from any surface, you

may release lead paint dust. LEAD IS TOXIC.

EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS

ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN

CHILDREN. PREGNANT WOMEN SHOULD ALSO

AVOID EXPOSURE. Wear a NIOSH approved respirator

to control lead exposure. Clean up carefully with a HEPA

vacuum and a wet mop. Before you start, find out how to

protect yourself and your family by contacting the National

Lead Information Hotline at 1-800-424-LEAD or log on to

www.epa.gov/lead.

PRIMING

Use of a Rust-Oleum

primer provides added corrosion

protection, excellent adhesion and hiding and is especially

recommended for bare wood and metal. The following

primers are recommended.

7769 Rusty Metal Primer

7780 Clean Metal Primer

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA SRT-09 STOPS RUST TEXTURED SPRAYS .DESCRIPTION AND USES ® . ..PAINTING CONDITIONS Rust-Oleum Stops Rust Textured Sprays are designed to provide a durable protective coating with excellent resistance to rust, and excellent resistance to abrasion, fading, chipping, and dulling. These sprays apply easily, provide excellent coverage and dry fast to a tough attractive finish. Rust-Oleum® Stops Rust® Textured Sprays are ideal for outdoor metal surfaces.
PAGE 2
TECHNICAL DATA STOPS RUST TEXTURED SPRAYS ..PRODUCT APPLICATION (cont.) . . APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use. Hold can upright 10-16" from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface. Keep the can in motion while spraying.
PAGE 3
TECHNICAL DATA STOPS RUST TEXTURED SPRAYS PHYSICAL PROPERTIES . TEXTURED SPRAYS Resin Type Solvent Acrylic Pigment Type Varies with color MIR 1.4 Max; 1.9 Max (metallic) Fill Weight 12 ounces Solvents Acetone, Toluene, Xylene Recommended Dry Film Thickness (DFT) Per Coat 1.0-2.0 mils (25-50µ) Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70°F (21°C) and 50% Relative Humidity 10-12 sq. ft./can (0.9-1.