MSDS

Date Printed: 5/13/2015
1-Methoxy-2-propyl acetate 108-65-6 5.0
50 ppm (AIHA
WEEL)
N.E. N.E. N.E.
Stoddard Solvent 8052-41-3 5.0 100 ppm N.E. 500 ppm N.E.
Ethylbenzene 100-41-4 5.0 20 ppm 125 ppm 100 ppm N.E.
Aluminum Flake 7429-90-5 5.0 1 mg/m3 N.E.
15 mg/m3 [Total
Dust]
N.E.
1,3,5-Trimethylbenzene 108-67-8 5.0 25 ppm N.E. N.E. N.E.
Iron Oxide 1309-37-1 5.0
5 mg/m3
(Respirable
Dust, OSHA)
N.E.
15 mg/m3 (Total
Dust)
N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use. A NIOSH/MSHA approved air purifying respirator with an organic
vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed
exposure limits.
Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any potential for an
uncontrolled release, exposure levels are not known, or in any other circumstances where air purifying respirators may not provide
adequate protection.
SKIN PROTECTION: Use impervious gloves to prevent skin contact and absorption of this material through the skin. Nitrile or
Neoprene gloves may afford adequate skin protection. Use gloves to prevent prolonged skin contact.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further information regarding personal
protective equipment and its application. Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
9. Physical and Chemical Properties
Appearance:
Liquid
Physical State:
Liquid
Odor:
Solvent Like
Odor Threshold:
N.E.
Relative Density:
0.938
pH:
N.E.
Freeze Point, °C:
N.D.
Viscosity:
N.D.
Solubility in Water:
Miscible
Partition Coefficient, n-octanol/
water:
No Information
Decompostion Temp., °C:
No Information
Boiling Range, °C:
257 - 400
Explosive Limits, vol%:
0.7 - 10.6
Flammability:
Does not Support Combustion
Flash Point, °C:
>94
Evaporation Rate:
Slower than Ether
Auto-ignition Temp., °C:
No Information
Vapor Density:
Heavier than Air
Vapor Pressure:
N.D.
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Flammable hydrogen gas will evolve when product comes in contact with water or damp air. Heat will be
generated. The amount of heat generated will depend upon the volume of material in contact. Avoid all possible sources of ignition.
Avoid temperatures above 120 ° F. Avoid contact with strong acid and strong bases.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies.
HAZARDOUS DECOMPOSITION: By open flame, carbon monoxide and carbon dioxide. When heated to decomposition, it emits
acrid smoke and irritating fumes. Contains solvents which may form carbon monoxide, carbon dioxide, and formaldehyde.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions.
11. Toxicological information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Causes Serious Eye Irritation
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Prolonged or repeated skin contact may cause irritation. Causes skin irritation.
Page 4 / 8