SDS

Date Printed: 5/15/2015
4. First-aid Measures
FIRST AID - EYE CONTACT: Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical
attention. Do NOT allow rubbing of eyes or keeping eyes closed.
FIRST AID - SKIN CONTACT: Wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation
develops or persists.
FIRST AID - INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen.
Get immediate medical attention. Do NOT use mouth-to-mouth resuscitation. If you experience difficulty in breathing, leave the
area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
FIRST AID - INGESTION: Aspiration hazard: Do not induce vomiting or give anything by mouth because this material can enter the
lungs and cause severe lung damage. Get immediate medical attention. If swallowed, get medical attention.
5. Fire-fighting Measures
EXTINGUISHING MEDIA:
Alcohol Film Forming Foam, Carbon Dioxide, Dry Chemical, Dry Sand, Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS: Isolate from heat, electrical equipment, sparks and open flame. Vapors can travel
to a source of ignition and flash back. Vapors may form explosive mixtures with air. No unusual fire or explosion hazards noted.
Closed containers may explode when exposed to extreme heat due to buildup of steam. Keep containers tightly closed.
SPECIAL FIREFIGHTING PROCEDURES: Water may be used to cool closed containers to prevent pressure buildup and possible
autoignition or explosion. Evacuate area and fight fire from a safe distance. Use water spray to keep fire-exposed containers cool.
Containers may explode when heated.
6. Accidental Release Measures
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Contain spilled liquid with sand or earth. DO NOT use
combustible materials such as sawdust. Eliminate all ignition sources; use explosion-proof equipment. Place material in a container
and dispose of according to local, provincial, state and federal regulations. Remove all sources of ignition, ventilate area and
remove with inert absorbent and non-sparking tools. Dispose of according to local, state (provincial) and federal regulations. Do not
incinerate closed containers. Ventilate area, isolate spilled material, and remove with inert absorbent. Dispose of contaminated
absorbent, container, and unused contents in accordance with local, state, and federal regulations.
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Wash hands before eating. Use only with adequate ventilation. Follow all
MSDS/label precautions even after container is emptied because it may retain product residues. Remove contaminated clothing
and launder before reuse. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.
STORAGE: Keep containers tightly closed. Isolate from heat, electrical equipment, sparks and open flame. Keep away from heat,
sparks, flame and sources of ignition. Keep container closed when not in use. Product should be stored in tightly sealed containers
and protected from heat, moisture, and foreign materials. Store in a dry, well ventilated place. Keep container tightly closed when
not in use. Avoid excess heat. Do not store above 120 ° F. Store large quantities in buildings designed and protected for storage of
NFPA Class II combustible liquids.
8. Exposure Controls/Personal Protection
Chemical Name CAS-No.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-TWA
OSHA PEL-
CEILING
n-Butyl Acetate 123-86-4 20.0 150 ppm 200 ppm 150 ppm N.E.
Limestone 1317-65-3 15.0
15 mg/m3 (Total
Dust, OSHA)
N.E.
5 mg/m3
(Respirable Dust)
N.E.
Solvent Naphtha, Light Aromatic 64742-95-6 15.0 N.E. N.E. N.E. N.E.
1,2,4-Trimethylbenzene 95-63-6 10.0
25 ppm (NIOSH
REL)
N.E. N.E. N.E.
Acrylic Polymer Proprietary 10.0 N.E. N.E. N.E. N.E.
1,3,5-Trimethylbenzene 108-67-8 5.0 25 ppm N.E. N.E. N.E.
Xylene (mixed isomers) 1330-20-7 5.0 100 ppm 150 ppm 100 ppm N.E.
Diethylbenzene, Mixed Isomers 25340-17-4 5.0 N.E. N.E. N.E. N.E.
Carbon Black 1333-86-4 5.0
3 mg/m3
(Inhalable Dust)
N.E. 3.5 mg/m3 N.E.
Ethylbenzene 100-41-4 1.0 20 ppm 125 ppm 100 ppm N.E.
Additive (Surfactant/Defoamer/
Drier/Rheology Modifer)
Proprietary 1.0 N.E. N.E. N.E. N.E.
Page 3 / 7