SDS

Date Printed: 5/8/2015
Barium Sulfate 7727-43-7 10.0
5 mg/m3
(Inhlalable
fraction w/o
asbestos and
<1% cryst.silica)
N.E.
15 mg/m3 [Total
Dust]
N.E.
n-Butyl Acetate 123-86-4 5.0 150 ppm 200 ppm 150 ppm N.E.
Ethylbenzene 100-41-4 5.0 20 ppm 125 ppm 100 ppm N.E.
Carbon Black 1333-86-4 5.0
3 mg/m3
(Inhalable Dust)
N.E. 3.5 mg/m3 N.E.
Propylene Glycol Monobutyl
Ether
5131-66-8 5.0 N.E. N.E. N.E. N.E.
Titanium Dioxide 13463-67-7 1.0
10 mg/m3 (Total
Dust)
N.E.
15 mg/m3 [Total
Dust]
N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Use explosion-proof ventilation equipment. Prevent build-up of vapors by opening all
doors and windows to achieve cross-ventilation. Provide general dilution of local exhaust ventilation in volume and pattern to keep
TLV of hazardous ingredients below acceptable limits.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use. A NIOSH/MSHA approved air purifying respirator with organic
vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed
exposure limits.
SKIN PROTECTION: Use impervious gloves to prevent skin contact and absorption of this material through the skin. Nitrile or
Neoprene gloves may afford adequate skin protection. Use gloves to prevent prolonged skin contact.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further information regarding personal
protective equipment and its application. Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
9. Physical and Chemical Properties
Appearance:
Aerosolized Mist
Physical State:
Liquid
Odor:
Solvent Like
Odor Threshold:
ND
Relative Density:
0.789
pH:
NE
Freeze Point, °C:
N.D.
Viscosity:
N.D.
Solubility in Water:
Slight
Partition Coefficient, n-octanol/
water:
No Information
Decompostion Temp., °C:
No Information
Boiling Range, °C:
-11 - 415
Explosive Limits, vol%:
0.7 - 13.0
Flammability:
Does not Support Combustion
Flash Point, °C:
>94
Evaporation Rate:
Faster than Ether
Auto-ignition Temp., °C:
No Information
Vapor Density:
Heavier than Air
Vapor Pressure:
ND
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid temperatures above 120 ° F. Avoid all possible sources of ignition. Avoid contact with strong acid
and strong bases.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies.
HAZARDOUS DECOMPOSITION: By open flame, carbon monoxide and carbon dioxide. When heated to decomposition, it emits
acrid smoke and irritating fumes. Contains solvents which may form carbon monoxide, carbon dioxide, and formaldehyde.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions.
11. Toxicological information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Causes Serious Eye Irritation
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Substance may cause slight skin irritation. Prolonged or repeated contact may
Page 4 / 7