SDS

Date Printed: 8/8/2022
Acrylic Resin
PROPRIET
ARY
0.1-1.0 GHS07-GHS08 H315-319-350-361
Naphtha, Hydrotreated Heavy 64742-48-9 0.1-1.0 GHS08 H304-340-350
Methyl Ethyl Ketoxime 96-29-7 0.1-1.0
GHS05-GHS06-
GHS07-GHS08
H302-312-315-317-318-331-336
-370-373
Zirconium Acetate 5153-24-2 <0.1 Not Available Not Available
4. First-Aid Measures
FIRST AID - EYE CONTACT: Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical
attention. Do NOT allow rubbing of eyes or keeping eyes closed.
FIRST AID - SKIN CONTACT: Wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation
develops or persists.
FIRST AID - INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get
immediate medical attention. Do NOT use mouth-to-mouth resuscitation. If you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
FIRST AID - INGESTION: Aspiration hazard: Do not induce vomiting or give anything by mouth because this material can enter the
lungs and cause severe lung damage. Get immediate medical attention. If swallowed, get medical attention.
5. Fire-Fighting Measures
EXTINGUISHING MEDIA: Alcohol Film Forming Foam, Carbon Dioxide, Dry Chemical, Dry Sand, Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS: FLASH POINT IS LESS THAN -7°C (20°F). EXTREMELY FLAMMABLE LIQUID
AND VAPOR!Water spray may be ineffective. Closed containers may explode when exposed to extreme heat due to buildup of
steam. Closed containers may explode when exposed to extreme heat. Vapors may form explosive mixtures with air. Vapors can
travel to a source of ignition and flash back. Isolate from heat, electrical equipment, sparks and open flame. Perforation of the
pressurized container may cause bursting of the can.
SPECIAL FIREFIGHTING PROCEDURES: Water may be used to cool closed containers to prevent pressure buildup and possible
autoignition or explosion. Full protective equipment including self-contained breathing apparatus should be used. Evacuate area and
fight fire from a safe distance. Use water spray to keep fire-exposed containers cool. Containers may explode when heated.
Special Fire and Explosion Hazard (Combustible Dust): No Information
6. Accidental Release Measures
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Contain spilled liquid with sand or earth. DO NOT use
combustible materials such as sawdust. Isolate the hazard area and deny entry to unnecessary and unprotected personnel. Remove
all sources of ignition, ventilate area and remove with inert absorbent and non-sparking tools. Dispose of according to local, state
(provincial) and federal regulations. Do not incinerate closed containers. Ventilate area, isolate spilled material, and remove with
inert absorbent. Dispose of contaminated absorbent, container, and unused contents in accordance with local, state, and federal
regulations.
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Wash hands before eating. Remove contaminated clothing and launder before reuse.
Use only with adequate ventilation. Follow all SDS and label precautions even after container is emptied because it may retain
product residues. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.
STORAGE: Keep containers tightly closed. Isolate from heat, electrical equipment, sparks and open flame. Contents under
pressure. Do not store above 120°F (49°C). Store large quantities in buildings designed and protected for storage of flammable
aerosols. Keep away from heat, sparks, flame and sources of ignition. Avoid excess heat. Product should be stored in tightly sealed
containers and protected from heat, moisture, and foreign materials.
Advice on Safe Handling of Combustible Dust: No Information
No Information
Page 3 / 8