SDS

Date Printed: 3/24/2023
FIRST AID - SKIN CONTACT: Wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation
develops or persists.
FIRST AID - INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get
immediate medical attention. Do NOT use mouth-to-mouth resuscitation. If you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
FIRST AID - INGESTION: If swallowed, get medical attention.
5. Fire-Fighting Measures
EXTINGUISHING MEDIA: Alcohol Film Forming Foam, Carbon Dioxide, Dry Chemical, Dry Sand, Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS: Closed containers may explode when exposed to extreme heat due to buildup of
steam. Keep containers tightly closed. Combustible liquid and vapor. No unusual fire or explosion hazards noted.
SPECIAL FIREFIGHTING PROCEDURES: Evacuate area and fight fire from a safe distance. Use water spray to keep fire-exposed
containers cool. Containers may explode when heated.
Special Fire and Explosion Hazard (Combustible Dust): No Information
6. Accidental Release Measures
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition, ventilate area and remove with
inert absorbent and non-sparking tools. Dispose of according to local, state (provincial) and federal regulations. Do not incinerate
closed containers.
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Wash hands before eating. Remove contaminated clothing and launder before reuse.
Use only with adequate ventilation. Follow all SDS and label precautions even after container is emptied because it may retain
product residues. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.
STORAGE: Store in a dry, well ventilated place. Keep container tightly closed when not in use. Keep containers tightly closed.
Isolate from heat, electrical equipment, sparks and open flame. Avoid excess heat.
Advice on Safe Handling of Combustible Dust: No Information
8. Exposure Controls / Personal Protection
Chemical Name CAS-No.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-TWA
OSHA PEL-
CEILING
Titanium Dioxide 13463-67-7 30.0 0.2 mg/m3 N.E. 15 mg/m3 N.E.
Xylenes (o-, m-, p- Isomers) 1330-20-7 15.0 20 ppm N.E. 100 ppm N.E.
Solvent Naphtha, Light Aromatic 64742-95-6 10.0 N.E. N.E. N.E. N.E.
Propylene Glycol Monomethyl
Ether
107-98-2 10.0 50 ppm 100 ppm N.E. N.E.
Ethylbenzene 100-41-4 5.0 20 ppm N.E. 100 ppm N.E.
1,2,4-Trimethylbenzene 95-63-6 5.0 10 ppm N.E. N.E. N.E.
Amorphous Silica 7631-86-9 5.0 N.E. N.E. 50 µg/m3 N.E.
Solvent Naphtha, Light Aromatic 64742-95-6 1.0 N.E. N.E. N.E. N.E.
Toluene 108-88-3 1.0 20 ppm N.E. 200 ppm 300 ppm
Ethanol 64-17-5 1.0 N.E. 1000 ppm 1000 ppm N.E.
n-Butyl Acetate 123-86-4 1.0 50 ppm 150 ppm 150 ppm N.E.
Cumene 98-82-8 1.0 5 ppm N.E. 50 ppm N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
Tub & Tile Base
Page 3 / 6