Use and Care Manual

TECHNICAL DATA
SPC-31
RUST-OLEUM
®
SPECIALTY
GLITTER SPRAYS
1
Form: GDH-857
Rev.: 100918
DESCRIPTION AND USES
Rust-Oleum
®
Glitter Sprays are designed to provide a sparkle
finish on many surfaces including wood, metal, wicker,
ceramic, pottery, Styrofoam
®*
, paper, plastic, and more. For
added protection, top coat with Rust-Oleum
®
Glitter Sealer.
The clear topcoat helps prevent Glitter from flaking and fading
while maintaining the sparkle finish. For use on interior items
only.
PRODUCTS
SKU
DESCRIPTION (Aerosol)
267689
Glitter Gold
267734
Glitter Silver
268045
Glitter Red
267736
Glitter Clear Sealer
276287
Glitter Bright Pink
277781
Glitter Kelly Green
278073
Glitter Multi Color Purple
299422
Glitter Harvest Orange
299424
Glitter Midnight Black
299425
Glitter Royal Blue
299426
Glitter Pearl White
302573
Glitter Turquoise
344697
Glitter Rose Gold
344696
Glitter Copper
PRODUCT APPLICATION
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50ºF (10ºC) and
90ºF (32ºC) and humidity is below 65% to ensure proper
drying. Do not apply to surfaces that, when heated, exceed
200°F (93°C). Avoid spraying in very windy and dusty
conditions. Cover surrounding area to protect from spray
mist.
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants
by washing the surface with a commercial detergent, or
other suitable cleaning method. Rinse with fresh water and
allow to thoroughly dry. Remove loose paint and rust with a
wire brush or sandpaper. Lightly sand glossy surfaces to
create a surface profile.
WARNING! If you scrape, sand or remove old paint from any surface,
you may release lead paint dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE; ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved
respirator to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
PRODUCT APPLICATION (cont.)
PRIMING
Use of a Painter’s Touch
®
Primer provides excellent
adhesion and hiding and is especially recommended for bare
wood and metal. A primer, however, is not recommended
for Styrofoam
®*
and paper. The following primers are
recommended.
249086
Red Primer
249088
Gray Primer
249058
White Primer
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle, DO NOT STRIKE
CAN. Contact Rust-Oleum. Shake often during use. Hold
can upright 12-14” from surface and spray in a steady back-
and-forth motion, slightly overlapping each stroke. Keep the
can the same distance from the surface. Keep the can in
motion while spraying. Apply two or more light coats a few
minutes apart. Do not use near open flame.
DRY & RECOAT
Dry and recoat times are based on 70ºF and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 20 minutes, to handle in 1 hour, and fully dry in 24
hours. Recoat at anytime.
CLEAN-UP
When finished spraying, clear valve by turning can upside
down and pushing spray button for 5 seconds. Clean-up wet
paint with xylene or mineral spirits. Properly discard empty
container. Do not burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object into
can valve opening.
*Styrofoam
®
is a trademark of the Dow Chemical Company