Use and Care Manual

ManualsBrandsRust-Oleum Specialty ManualsCraft & Art Supplies11 oz. Chalkboard Flat Black Spray Paint (6-Pack)

TECHNICAL DATA SPC-03

SPECIALTY

CHALKBOARD SPRAY

Form: GDH-325

Rev.: 042114

.DESCRIPTION AND USES .

A finish that converts wood, metal, plastic, glass,

paperboard, and hardboard into a useable chalkboard

surface.

.PRODUCTS .

SKU Description

1913830 Black (12 ounces)

. PRODUCT APPLICATION .

SURFACE PREPARATION

ALL SURFACES: Remove all dirt, grease, oil, salt and

chemical contaminants by washing the surface with a

commercial detergent, or other suitable cleaning method.

Mold and mildew must be cleaned with a chlorinated

cleaner or bleach solution. Rinse with fresh water and

allow to thoroughly dry.

STEEL: Scrape and wire brush or power tool clean to

remove loose rust, scale, and deteriorated coatings. Use

7569838 Red Primer for sound rusted or clean metal

before application of a finish coat.

PREVIOUSLY COATED: Previously coated surfaces must

be sound and in good condition. Smooth, hard, or glossy

surfaces should be scarified by sanding to create a

surface profile.

Removal of old paint by sanding, scraping or other means

may generate dust or fumes that contain lead. LEAD IS

TOXIC. Contact the U.S.EPA/Lead Information Hotline at

1-800-424- LEAD pr log on to www.epa.gov/lead.

.PRODUCT APPLICATION (cont.) .

APPLICATION

Apply only when air and surface temperatures are

between 50-90°F (10-32°C) and the relative humidity is

below 85% to ensure proper drying. Use in a properly

ventilated area. Cover surrounding area to protect from

overspray. Overspray can carry a significant distance.

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE CAN. Contact Rust-Oleum. Hold can upright 12-

16" from surface and spray in a steady back and forth

motion, slightly overlapping each stroke. Keep the can the

same distance from the surface. Keep the can in motion

while spraying. Apply several light coats a few minutes

apart to avoid drips and runs. Do not use near open

flame.

When fully dry, prepare the surface for use by rubbing side

of chalk over the entire surface. Erase and the chalkboard

is ready for use. For best results, use only calcium

carbonate chalk and felt erasers. Other chalks will scratch

the surface.

DRY & RECOAT

Dry and recoat times are based on 70ºF (21°C) and 50%

relative humidity. Dries tack free in 20 minutes and can be

handled in 1 hour. Recoat within 1 hour or after 24 hours.

CLEAN-UP

Clean valve immediately after use by turning can upside

down and depressing spray button for 3-5 seconds (some

paint will be sprayed out, so be careful to not inadvertently

spray yourself or other objects). Clean up wet paint with

xylene or mineral spirits. Throw away empty can in trash

pick-up. Do not burn or place in home trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object

into can valve opening.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA SPC-03 SPECIALTY CHALKBOARD SPRAY .DESCRIPTION AND USES . .PRODUCT APPLICATION (cont.) APPLICATION A finish that converts wood, metal, plastic, glass, paperboard, and hardboard into a useable chalkboard surface. .PRODUCTS SKU 1913830 Apply only when air and surface temperatures are between 50-90°F (10-32°C) and the relative humidity is below 85% to ensure proper drying. Use in a properly ventilated area. Cover surrounding area to protect from overspray.
PAGE 2
TECHNICAL DATA PEEL STOP – SPECIALTY CHALKBOARD SPRAY .PHYSICAL PROPERTIES . Physical Properties CHALKBOARD SPRAY Resin Type Acrylic Modified Alkyd Pigment Type Carbon Black Solvents Acetone, Mineral Spirits, VM&P Naphtha, Xylene MIR 1.20 Max Fill Weight 12 ounces Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70-80ºF (21-27ºC) and 50% Relative Humidity Approximately 7 sq.ft./can 2 (0.