SDS

Date Printed: 7/18/2016
Bisphenol A Epoxy Resin 25085-99-8 65.0 N.E. N.E. N.E. N.E.
Neopentyl Glycol Diglycidyl
Ether
17557-23-2 15.0 N.E. N.E. N.E. N.E.
Titanium Dioxide 13463-67-7 15.0 10 mg/m3 N.E. 15 mg/m3 N.E.
1-Chloro-4-(Trifluoromethyl)
Benzene
98-56-6 10.0 N.E. N.E. N.E. N.E.
Carbon Black 1333-86-4 1.0 3 mg/m3 N.E. 3.5 mg/m3 N.E.
2,6-Dimethyl-4-Heptanone 108-83-8 1.0 25 ppm N.E. 50 ppm N.E.
Stoddard Solvent 8052-41-3 1.0 100 ppm N.E. 500 ppm N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
9. Physical and Chemical Properties
Appearance:
Liquid
Physical State:
Liquid
Odor:
Solvent Like
Odor Threshold:
N.E.
Relative Density:
1.257
pH:
N.A.
Freeze Point, °C:
N.D.
Viscosity:
No Information
Solubility in Water:
Slight
Partition Coefficient, n-octanol/
water:
N.D.
Decompostion Temp., °C:
N.D.
Boiling Range, °C:
139 - 220
Explosive Limits, vol%:
0.9 - 10.5
Flammability:
Does not Support Combustion
Flash Point, °C:
149
Evaporation Rate:
Slower than Ether
Auto-ignition Temp., °C:
N.D.
Vapor Density:
Heavier than Air
Vapor Pressure:
N.D.
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid contact with strong acid and strong bases.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies.
HAZARDOUS DECOMPOSITION: When heated to decomposition, it emits acrid smoke and irritating fumes.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions.
11. Toxicological information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Irritating, and may injure eye tissue if not removed promptly.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Low hazard for usual industrial handling or commercial handling by trained
personnel.
EFFECTS OF OVEREXPOSURE - INHALATION: High gas, vapor, mist or dust concentrations may be harmful if inhaled. Avoid
breathing fumes, spray, vapors, or mist.
EFFECTS OF OVEREXPOSURE - INGESTION: Substance may be harmful if swallowed.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS: Reports have associated repeated and prolonged occupational
overexposure to solvents with permanent brain and nervous system damage. Contains carbon black. Chronic inflammation, lung
fibrosis, and lung tumors have been observed in some rats experimentally exposed for long periods of time to excessive
concentrations of carbon black and several insoluble fine dust particles. Tumors have not been observed in other animal species
(i.e., mouse and hamster) under similar circumstances and study conditions. Epidemiological studies of North American workers
show no evidence of clinically significant adverse health effects due to occupational exposure to carbon black.
Page 3 / 5