Instructions / Assembly
TECHNICAL DATA RST-03
RESTORE
™
EXTREME CONCRETE
Form: GDH-99
Rev.: 082415
1
DESCRIPTION AND USES .
Restore
™
Extreme Concrete is a pigmented water-proofing
sealer for concrete that provides protection from water, alkalis,
acids, ultraviolet light and staining. It is suitable for use on
broom/brushed concrete driveways.
FOR EXTERIOR USE ONLY. NOT FOR USE ON ASPHALT.
.PRODUCTS .
SKU Description
44000 4-Gallon Extreme Tint Base
44007 4-Gallon Extreme Cape Cod Gray
44035 4-Gallon Extreme Sandstone
.COMPANION PRODUCTS .
SKU Description
51752 Restore Deck & Concrete Cleaner
51750 Restore Crack Filler
RRC-9-2009 Restore 9” Roller
92018 Restore 18” Roller
..PRODUCT APPLICATION .
SURFACE PREPARATION
Proper surface preparation is critical to performance. Surface
must be clean and free of dirt, grease, mildew and organic
growth to ensure product bonding and adhesion. Sand or scrape
any loose paint. Smooth or glossy surfaces should be sanded or
de-glossed before application. Clean the surface using a brush
and Restore Deck & Concrete Cleaner or suitable non-bleach
cleaner. For grease/oil spots, use tri-sodium phosphate (TSP)
according to the manufacturer’s directions. Patch cracks,
potholes and depressions in concrete using cement-based
patching material. Use Restore Crack Use a filler or similar latex
based caulk to fill cracks larger than 1/16”. For cracks larger than
1/4 “, use a cement patch according to manufacturer’s
instructions. Troweled concrete must be ground or mechanically
abraded prior to installing Restore Extreme Concrete.
..PRODUCT APPLICATION (cont.)
APPLICATION
Apply when ambient air and surface temperatures are between
50-90°F (10-32°C) and the relative humidity is less than 85%.
DO NOT APPLY IF RAIN IS EXPECTED WITHIN 24 HOURS
OF APPLICATION.
When applying in hot conditions and/or in direct sunlight,
dampen the surface with a fine mist of water. Be careful not to
apply too much mist causing water to puddle. This will slow the
drying time. Evaporation may occur quickly during hotter weather
causing the product to thicken. If this occurs, add up to ½ pint (8
oz.) of water per gallon and mix thoroughly.
Thoroughly power mix prior to application and stir occasionally
during application. Box material if using more than one container
to ensure color consistency. Pour into a wide (18”) roller tray and
fill tray approximately half full. Using the 18” Restore Roller™,
saturate and load the roller cover in the tray by rolling back and
forth. For smaller areas, a 9” Restore Roller may be used. If
using the 9” Restore Roller use the roller tray or work directly
from container using a roller grid. Apply generously in a
consistent pattern using slight downward pressure. Maintain a
wet bead of material in front of the roller and work to a wet edge
at all time. Slowly roll only in one direction avoiding back and
forth motion. Avoid overworking and repeated rolling back into
coated areas where drying has begun. Avoid puddling.
Allow to dry for 3-6 hours and apply a second coat.
Restore Extreme Concrete will fill hairline cracks. Fill these
damaged areas with a heavily loaded brush or roller by dabbing
these areas until the gaps or cracks are filled. Cut in around
edges with a brush.
CONSUMPTION
4-gallon pail covers 100-120 square feet with two coats.
DRY TIMES
Dries to the touch in 2 hours and can be recoated in 3-6 hours.
Allow final coat to dry 12 hours before foot traffic and 7 days
before vehicle traffic. Cool or humid conditions require longer
drying time.
CLEAN-UP
When finished, wash tools and equipment with mild soap
and warm water. Properly dispose of all soiled rags and
protect unused product from freezing.