Use and Care Manual
TECHNICAL DATA RST-15
RESTORE
®
OUTDOOR FURNITURE
Form: GDH-691
Rev.: 030717
1
DESCRIPTION AND USES .
Restore
®
Outdoor Furniture is a water-based acrylic coating
designed for use on structurally sound wood furniture such as
picnic tables and play sets.
Not for use on composite decking, concrete, fiberglass, tile
or metal surfaces. These surfaces will not allow for proper
adhesion. Do not use on driveways, garages or other
areas with vehicular traffic.
FOR EXTERIOR USE ONLY AND NOT RECOMMENDED
FOR DRIVEWAYS, GARAGES OR OTHER AREAS WITH
VEHICULAR TRAFFIC.
Restore Outdoor Furniture tint base must be tinted at the
store of purchase. DO NOT APPLY IF PRODUCT HAS NOT
BEEN TINTED. Restore Outdoor Furniture can be applied
using a 4” wide, ⅜” or ½” nap roller or a synthetic paint
brush. Use of the Restore Honeycomb Roller is NOT
recommended.
. FEATURES .
Smooth finish
Conceals hairline cracks
Extends life of wood furniture
Long lasting protection
.PRODUCTS .
SKU Description
287508 Outdoor Furniture – 1-Gallon
287509 Outdoor Furniture – 1-Quart
COMPANION PRODUCTS ...
SKU Description
51752 Restore Deck & Concrete Cleaner
51750 Restore Crack Filler
287517 Restore Deck Start Wood Primer
287912 Restore Deck Stripper
PRODUCT APPLICATION .
REGARDLESS OF AGE OR SURFACE CONDITION,
FAILURE TO FOLLOW ONE OF THESE PREPARATION
METHODS WILL RESULT IN POOR ADHESION AND
POSSIBLE COATINGS FAILURE. NEW AND SEALED WOOD
DECKS NEED TO WEATHER AT LEAST 6 MONTHS
BEFORE APPLICATION.
READ ALL INSTRUCTIONS BEFORE BEGINNING
PROJECT.
SURFACE PREPARATION
NEW WOOD
New wood may be wet with chemicals or have mill glaze from
the manufacturing process. New wood should age for a
minimum of 6 months before applying Restore Outdoor Furniture.
The lumber must be dry completely before applying the product
to prevent peeling of the coating. The surface must also be
properly cleaned and prepared using Restore Deck & Concrete
Cleaner to remove all foreign material and mill glaze prior to
application. Follow the PREPARATION instructions to ensure
the Restore Outdoor Furniture adheres properly to the wood.
PRODUCT APPLICATION (cont) .
PREPARATION WITH RESTORE DECK START WOOD
PRIMER (HIGHLY RECOMMENDED)
Clean the surface using a bristle brush and Restore Deck &
Concrete Cleaner. The surface must be clean and free of dirt,
grease, mildew and organic growth. Loose paint needs to be
scraped. Raised nails heads and/or screws should be secured
using a hammer or screwdriver. Remove loose splinters. Fill
cracks with Restore Crack Filler or similar acrylic or non-silicone
filler. Allow to dry. Apply Restore Deck Start Wood Primer using
a synthetic paint brush. Apply generously in a consistent pattern.
Work to a wet edge at all times.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control lead
exposure. Clean up carefully with a HEPA vacuum and a wet
mop. Before you start, find out how to protect yourself and your
family by contacting the National Lead Information Hotline at
1-800-424-LEAD or log on to www.epa.gov/lead.
PREPARATION WITH RESTORE DECK STRIPPER
Previously applied coatings and existing stain/sealers need to be
removed completely. Strip the surface using a deck brush and
Restore Deck Stripper. The sand the surface using 50 or 60 grit
sandpaper. Follow by cleaning the surface using a bristle brush
and Restore Deck & Concrete Cleaner. The surface must be
clean and free of dirt, grease, mildew and organic growth. Allow
to dry. Raised nails heads and/or screws should be secured
using a hammer or screwdriver. Remove loose splinters. Fill
cracks with Restore Crack Filler or similar acrylic, non-silicone
filler. Allow to dry.
Conduct a splash test by sprinkling water on the surface. If the
water absorbs rapidly into the wood, the surface is ready to coat.
If the water beads, puddles or is not absorbed, the surface is not
ready to coat and requires more surface preparation. Continue
the process until the water absorbs into the wood in all test areas.
PRECAUTIONS & TEMPERATURE SAFEGUARDS
DO NOT APPLY IF RAIN IS EXPECTED WITHIN 48 HOURS
OF APPLICATION. Apply when sir and surface temperature is
between 50-90°F (10-32°C) and will remain between 50° and
90°F for at least 72 hours (day and night) after application.