Instructions / Assembly

ManualsBrandsRust-Oleum Restore ManualsPaint1 gal. 10X Advanced River Rock Deck and Concrete Resurfacer

RESTORE 10X Advanced Resurfacer – Tips & Application Instructions

Page 1 of 5

READ ALL INSTRUCTIONS BEFORE BEGINNING

For videos, information, and helpful tips on preparation, deck application, concrete application, and

maintenance; visit rustoleum.com/restore.

1. SURFACES

Wood: Restore 10X Advanced Resurfacer should only be applied on horizontal, structurally sound wood and most

composite surfaces. Some composite decking is engineered with moisture repellants or sealers that may prevent

proper adhesion. Be sure to follow specific manufacturer’s recommendation before applying to any composite

decking.

NOT FOR USE ON: Smooth or floated concrete, fiberglass, tile, and metal surfaces. These surfaces will not allow

for proper adhesion. Do not use on driveways, garages, or other areas with vehicular traffic.

2. NEW WOOD

New wood may be wet with chemicals or have mill glaze from the manufacturing process. New wood should age

for a minimum of 6 months before applying Restore 10X Advanced Resurfacer. The lumber must dry completely

before applying the product to prevent peeling of the coating. The surface must also be properly cleaned and

prepared using Restore Deck & Concrete Cleaner to remove all foreign material and mill glaze prior to application.

Follow the PREPARATION instructions to be sure the Restore 10X Advanced Resurfacer adheres properly to the

wood.

3. TINTING

Restore 10X Advanced Resurfacer tint base must be tinted at the store of purchase. DO NOT APPLY IF PRODUCT

HAS NOT BEEN TINTED.

4. COVERAGE

• One 1-gallon can of Restore 10X Advanced Resurfacer will cover up to 40 square feet with two coats

• One 4-gallon bucket of Restore 10X Advanced Resurfacer will cover up to 160 square feet with two coats

* TWO COATS ARE REQUIRED FOR EVERY SURFACE

5. SURFACE PREPARATION FOR WOOD

Stop, Watch, and Roll: For more information and helpful tips watch the Preparation with the Restore Deck Start

Wood Primer and/or Preparation with Restore Deck Stripper videos.

APPLICATION INSTRUCTIONS READ ALL INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING.

REGADLESS OF AGE OR SURFACE CONDITION, FAILURE TO FOLLOW ONE OF THESE PREPARATION METHODS WILL

RESULT IN POOR ADHESION AND POSSIBLE COATING FAILURE. NEW AND SEALED WOOD DECKS NEED TO

WEATHER AT LEAST SIX MONTHS BEFORE APPLICATION.

METHOD 1: PREPARATION WITH RESTORE DECK START WOOD PRIMER (HIGHLY RECOMMENDED)

Step 1 – Clean:

Clean the surface using a deck brush and the Restore Deck & Concrete Cleaner. The surface must be completely

clean and free of dirt, grease, mildew and organic growth to ensure product bonding and adhesion. For best

results use a pressure washer, in addition to the Restore Deck & Concrete Cleaner, to remove embedded dirt and

grime. (Use at a low setting 500-1200 PSI. Do not use high pressure as it may harm the wood.) For mildew and

Summary of content (5 pages)

PAGE 1
RESTORE 10X Advanced Resurfacer – Tips & Application Instructions Page 1 of 5 READ ALL INSTRUCTIONS BEFORE BEGINNING For videos, information, and helpful tips on preparation, deck application, concrete application, and maintenance; visit rustoleum.com/restore. 1. SURFACES Wood: Restore 10X Advanced Resurfacer should only be applied on horizontal, structurally sound wood and most composite surfaces. Some composite decking is engineered with moisture repellants or sealers that may prevent proper adhesion.
PAGE 2
RESTORE 10X Advanced Resurfacer – Tips & Application Instructions Page 2 of 5 other organic growth use a diluted solution of household bleach (3 parts water to 1 part bleach) applied to the surface before cleaning. Loose paint needs to be scraped and removed from the surface. Step 2 – Light Repairs: Raised nail heads and/or screws should be secured using a hammer or a screwdriver. Remove loose splinters and replace severely damaged or rotting boards.
PAGE 3
RESTORE 10X Advanced Resurfacer – Tips & Application Instructions Page 3 of 5 Step 4 – Light Repairs: Raised nail heads and/or screws should be secured using a hammer or a screwdriver. Remove loose splinters and replace severely damaged or rotting boards. Fill larger cracks using RESTORE CRACK FILLER or a similar acrylic, non-silicone filler. Allow to dry. 6.
PAGE 4
RESTORE 10X Advanced Resurfacer – Tips & Application Instructions Page 4 of 5 8. TWO COATS TWO COATS OF RESTORE 10X ADVANCED RESURFACER ARE REQUIRED. The first coat will go on to fill in cracks and do other minor repairs. The product will soak into the wood and dry. The first coat may be blotchy and spotty. The second coat works as a finishing coat and will give greater wear as the product ages. Be careful not to over spread.
PAGE 5
RESTORE 10X Advanced Resurfacer – Tips & Application Instructions Page 5 of 5 CAUTIONS: CONTAINS CRYSTALLINE SILICA. Adequate ventilation with air flow away from the user is required when sanding or abrading the dried film. If adequate ventilation cannot be provided, wear an approved particulate respirator (NIOSH-approved). Follow respirator manufacturer's directions for respirator use. 15.