Use and Care Manual

ManualsBrandsRust-Oleum Parks ManualsKitchen1 gal. Gloss 275 VOC Oil-Based Interior Polyurethane (4-Pack)

TECHNICAL DATA PKS-06

PRO FINISHER

POLYURETHANE 275 VOC

Form: GDH-892

Rev.: 071216

.DESCRIPTION AND USES .

Pro Finisher Polyurethane 275 VOC is a traditional wood floor

finish that meets the stringent requirements of all states that

enforce a 275 VOC regulation. This professional grade

polyurethane is recommended for all wood floors and all other

interior wood surfaces where a fast drying beautiful protective

finish is required. Pro Finisher Polyurethane provides a warm,

slightly ambered clear coating that accents the richness of wood

flooring. The finish will darken somewhat with time and exposure

to sunlight.

.PRODUCTS .

SKU (1-Gallon) Description

330813 Gloss

330833 Semi-Gloss

330823 Satin

..SURFACE PREPARATION .

Surfaces must be clean, dry, and free of wax, grease, oil, shellac,

lacquer, mildew, and polishes.

SANDING SURFACE:

Sand area smooth, progressing in sandpaper grit from rough to

medium to fine. For hardwood floors, use NOFMA and NHFA

accepted methods or see Pro Finisher Professional Finishing

Techniques for sanding details. After sanding vacuum surface

and wipe with a cloth to remove all dust.

WARNING! If you scrape, sand or remove old paint, you may

release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD

DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN

DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN

SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved

respirator to control lead exposure. Clean up carefully with a

HEPA vacuum and a wet mop. Before you start, find out how to

protect yourself and your family by contacting the National Lead

Information Hotline at 1-800-424-LEAD or log on to

www.epa.gov/lead.

STAINING SURFACE:

Oil or water based stains can be used prior to finish application

for custom coloring. Allow stain to dry thoroughly. Test a sample

area for product compatibility. If applying stain, do not use a

sanding sealer before staining. Oil-Base finish may be applied

directly over thoroughly dry stain.

SEALING SURFACE:

A sanding sealer may be used as an option to initially coat bare

wood surface. It penetrates and seals the wood and dries quickly.

Pro Finisher Universal Sealer is recommended because of its

excellent adhesion and extremely fast dry time. Sealer must be

completely dry before applying finish.

SURFACE PREPARATION (cont.) .

REFURBISH PREFINISHED SURFACE:

If existing finished wood surface or wood floor is in good

condition and free from wax or other contaminates, you may

recoat without sanding the surface to bare wood. A thorough

cleaning and abrading of prefinished surface is required. If

compatibility with the old finish is unknown, a sealer coat of Pro

Finisher Universal Sealer will minimize potential adhesion

problems.

..PRODUCT APPLICATION .

Stir contents before using and frequently during use. Do not

shake container. Apply Pro Finisher Polyurethane Finish using a

synthetic or Lambswool applicator pad, natural bristle brush,

polyester brush, short nap roller or weighted T-bar. Apply in

direction of wood grain in smooth, level strokes. Apply thin, even

coats at a rate of 350-450 square feet per gallon. Allow product

to dry 8-10 hours until film is totally dry. Environmental conditions

or heavy application of finish may extend dry times. Heavy

application of finish is not recommended. After first coat has dried,

abrade the surface using 120 to 150 grit sandpaper. Vacuum

and wipe clean. Follow this procedure for successive coats.

Sanding between coats is not required for intercoat adhesion as

long as the timeline between coats does not exceed 15 hours.

Sanding between coats produces a smooth, better looking job. A

minimum of 2-3 coats is recommended. Allow final coat to dry

overnight before permitting use of surface. Finish will take up to

30 days to completely cure. Do not place area rugs on floor, and

avoid exposure to washing and heavy traffic for a minimum of 2

weeks.

COVERAGE

Varies with surface porosity and will cover approximately 400

square feet per gallon.

DRY TIME

Dry times are based on 70°F and 50% relative humidity. Pro

Finisher Polyurethane 275 VOC dries to the touch in 4-5 hours

and can be recoated in 8-10 hours. Full cure will be reached in

30 days.

CLEAN-UP

Clean application tools and equipment with mineral spirits or

paint thinner.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA PKS-06 PRO FINISHER POLYURETHANE 275 VOC .DESCRIPTION AND USES SURFACE PREPARATION (cont.) . REFURBISH PREFINISHED SURFACE: Pro Finisher Polyurethane 275 VOC is a traditional wood floor finish that meets the stringent requirements of all states that enforce a 275 VOC regulation. This professional grade polyurethane is recommended for all wood floors and all other interior wood surfaces where a fast drying beautiful protective finish is required.
PAGE 2
TECHNICAL DATA PRO FINISHER POLYURETHANE 275 VOC PHYSICAL PROPERTIES . OIL BASE POLYURETHANE 275 VOC Resin Type Oil Modified Polyurethane Pigments NA Solvents Mineral Spirits Per Gallon Weight Solids 8.7-8.9 lbs. Per Liter 1.04-1.07 kg By Weight 40.1-41.4% By Volume 41.7-42.1% Volatile Organic Compounds 275 g/l (2.29 lbs./gal.) Recommended Dry Film Thickness (DFT) per Coat 1.5 mils (37.5µ) Wet Film to Achieve DFT (unthinned material) 3.5 mils (87.