Specification

ManualsBrandsRust-Oleum Marine ManualsPaint1-qt. White Semi-Gloss Topside Paint

TOPSIDE

PAINT

UV protection 

Abrasion & 

weather resistant

Excellent leveling

WARNING!

COMBUSTIBLE

LIQUID AND VAPOR 

(See Other Cautions On Back Panel)

32 FL. OZ. (1 QT) .946L

For use above

the waterline on

FIBERGLASS

WOOD

METAL

marine COATINGS

White

Gloss

Rust-Oleum Marine Coatings Topside Paint is an oil-based modified alkyd.

This easy to apply coating provides long-lasting protection and a brilliant

glossy finish on fiberglass, wood or metal. Use above the waterline only.

THINNER & CLEANER: Mineral spirits

APPLICATION TEMP: 50°F - 90°F

SURFACE PREPARATION: Proper surface preparation is key to a smooth, last-

ing finish. Surface must be free of dirt, loose paint, rust, oil, grease, wax, soap

and any other foreign matter. Wash with a solution of 2 cups household

ammonia per gallon of water and rinse well. Remove existing mildew with

household bleach instead of ammonia.

Never mix ammonia & bleach. Rinse

thoroughly and allow to dry.

BARE FIBERGLASS: The entire surface to be painted, regardless of age, must

be thoroughly washed with a fiberglass dewaxer to remove all traces of mold

release agents and wax. Sand the gelcoat with 80-120 grit sandpaper to a dull,

frosty appearance; solvent clean to remove residue. If the surface is in excel-

lent condition, proceed with the first coat of Topside Paint.

If the surface is rough or imperfections exist, it will have to be repaired. Fill all

nicks and gouges with a fiberglass repair compound; sand smooth when

hard, then solvent clean. Follow with a coat of Rust-Oleum Marine Coatings

Primer for Wood & Fiberglass to smooth the surface and provide a uniform

base; sand smooth and solvent clean. Proceed with the first coat of Topside

Paint.

BARE WOOD: Sand the surface smooth with 80-120 grit sandpaper; solvent

clean to remove residue. Fill all screwheads or small holes with a mender;

sand smooth and solvent clean. Apply a coat of Rust-Oleum Marine Coatings

Spar Varnish thinned 10% with mineral spirits to penetrate and seal the

porous grain. Follow directions and dry times on Spar Varnish. Apply one or

two coats of Rust-Oleum Marine Coatings Primer for Wood & Fiberglass until

an evenly smooth base condition is reached; sand each coat with 80-120 grit

sandpaper and solvent clean. Use a tack cloth to remove sanding dust and

proceed with the first coat of Topside Paint. Bare wood that has been epoxied

must be thoroughly scrubbed with an ammonia/water solution then sanded

with 120 grit sandpaper and solvent cleaned. Follow with a coat of Primer for

Wood & Fiberglass to smooth the surface and provide a uniform base; sand

well and solvent clean then proceed with the first coat of Topside Paint.

BARE STEEL: Sandblast to bare metal or abrade with emery cloth or grit

wheel. Solvent wash and allow to dry. Immediately apply one coat of Rust-

Oleum Marine Coatings Primer for Metal; allow to dry 24 hours. Proceed with

the first coat of Topside Paint.

Not for use on galvanized surfaces.

BARE ALUMINUM SURFACES:

Wipe the surface free of oil and grease with

solvent. Remove oxidation and abrade the surface with medium grit emery

cloth; remove sanding residue with a tack cloth. Apply one coat of Rust-Oleum

Marine Coatings Primer for Metal; allow to dry 24 hours. Proceed with the first

coat of Topside Paint.

PAINTED SURFACES: If the old paint is in good, sound condition, sand it thor-

oughly smooth with 150 grit sandpaper; solvent clean to remove residue, then

proceed with the first coat of Topside Paint. If the old paint is in poor condi-

tion, remove it with a paint & varnish remover or by sanding. Proceed with

instructions for the appropriate bare surface system.

APPLICATION DATA: Stir thoroughly before use. Apply with a brush, roller,

conventional or airless spray. If necessary for brush or roller application, thin

with no more than 5% mineral spirits. For best results on large, smooth sur-

faces roll out using a short nap or foam roller followed immediately by level-

ing off with the tip of a brush. For conventional spray application, thin 10-15%

with Xylene. Apply one thin, even coat per day. Allow to dry overnight, lightly

sand with 220 grit sandpaper, wipe with a tack cloth and apply a second coat.

Applying two or more coats in one day or applying excessively heavy films

(greater than 4 wet mils) will lead to insufficient drying of the paint and will

yield soft paint films. For airless spray application, no thinning is required.

Dries completely in 24 hours. Do not apply on extremely humid days (90%

humidity or above) or when rain is threatening. Do not apply in the late after-

noon when working outdoors as the wet film may be adversely affected by

dew. When working in cooler temperatures be sure the air and surface tem-

peratures will remain at or above 50°F for at least 8 hours after application

NON-SLIP DECKS: To provide a safe, slip-resistant texture on decks, add

Rust-Oleum Marine Coatings Anti-Slip Additive to the mixed Topside Paint.

Stir mixture continuously to insure compound is thoroughly dispersed and

remains in suspension. A minimum of two coats are recommended. No sand-

ing is required between coats. Allow to dry 24 hours for light use, 3 days for

full use. If preferred, apply a coat of Topside Paint without Anti-Slip Additive

to all areas requiring a non-skid surface then sprinkle or broadcast the Anti-

Slip Additive into the wet Topside Paint. After drying overnight carefully brush-

out all loose Anti-Slip Additive and apply another thin, even coat of Topside

Paint to the surface. For decks that have a pre-molded, non-skid embossment,

wash the surface with a dewaxer. Abrade area thoroughly with bronze wool

and solvent clean to remove residue. Apply two coats of Topside Paint, adding

Anti-Slip Additive to the mixture if an improved non-slip texture is desired.

Contains: Petroleum Distillates. VAPOR HARMFUL. MAY AFFECT

THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE

OR NAUSEA. CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION.

NOTICE: Reports have associated repeated and prolonged occupa-

tional overexposure to solvents with permanent brain and nervous

system damage. Do not breathe vapors, spray mist, sanding dust or

overspray. Ensure fresh air entry during application and drying. If you

experience eye watering, headache or dizziness or if air monitoring

demonstrates vapor/mist levels are above applicable limits, wear an

appropriate, properly fitted respirator (NIOSH/MSHA approved) dur-

ing and after application. Follow respirator manufacturer’s directions

for respirator use. Avoid contact with eyes, skin and clothing. Wash

thoroughly after handling. Keep away from heat and flame.

Use only

with adequate ventilation.

Prevent build-up of vapors by opening all

windows and doors to achieve cross-ventilation. Close container after

each use.

FIRST AID: If you experience difficulty in breathing, leave

the area to obtain fresh air. If continued difficulty is experienced, get

medical assistance immediately. In case of eye contact, flush immedi-

ately with plenty of water for at least 15 minutes and get medical

attention; for skin, wash thoroughly with soap and water. If swal-

lowed, do not induce vomiting. Get medical attention immediately. If

spilled, contain spilled material and remove with inert absorbent.

Dispose of contaminated absorbent, container and unused contents in

accordance with local, state and federal regulations.

WARNING: This

product contains chemicals known to the state of Califonia to cause

cancer and birth defects or other reproductive harm. KEEP OUT OF

REACH OF CHILDREN. INTENTIONAL MISUSE BY DELIBERATELY

CONCENTRATING AND INHALING THE CONTENTS MAY BE HARM-

FUL OR FATAL.

We stand behind our products. If you are dissatisfied with this prod-

uct, contact Rust-Oleum Technical Services at 1-800-395-7878 for a

refund of the product purchase price. Please note that the perfor-

mance of any marine coating depends on many factors outside the

control of Rust-Oleum, including surface preparation, proper applica-

tion and environmental conditions.

20066 1 1 8 86

# 206999

206936 1103

Made in U.S.A.

1-800-481-4785

www.rustoleum.com

www.paintideas.com