Use and Care Manual
TECHNICAL DATA
ROC-173
RUST-OLEUM
®
HOME
FLOOR COATING KITS
1
Form: ARJ-1992
Rev.: 031920
DESCRIPTION AND USES
Rust-Oleum
®
Home Floor Coating is an extremely durable,
easy to use, revolutionary technology that allows you to coat
over a wide variety of substrates inside the home without
stripping, sanding or priming. Transform any room by
revamping your outdated floor - simply clean, apply the
required Base Coat + Top Coat system for a brand new look
to your space.
For use on any bare, stained, sealed or previously coated
surfaces such as ceramic tile, porcelain tile, concrete, hard
wood, laminate, vinyl and linoleum.
Great for laundry rooms, basements, kitchens, bathrooms,
and more.
PRODUCT FEATURES
2 Step System
No stripping, sanding or priming
Superior adhesion to tough surfaces
Maximum scratch and stain resistance
Walk on in one day
PRODUCTS
SKU
DESCRIPTION (Kit)
360098
Home Ultra White/Tint Base Matte Kit
360099
Home Ultra White/Tint Base Semi-Gloss Kit
360100
Home Deep Tint Base Matte Kit
360101
Home Deep Tint Base Semi-Gloss Kit
KIT CONTENTS
1-Quart Base Coat
1-Quart Top Coat
1-4 oz. Cleaner
NOTE: Ultra White Tint Base can be applied as is for White
or tinted prior to application.
Two base coats are required
when applying the Ultra White Tint Base in White.
Deep Tint
Base must be tinted prior to application.
OTHER SUPPLIES NEEDED (not included in kit)
3/8" Nap Roller Sleeve
1/4" Nap Roller Sleeve
Roller Frame
Roller Pan
Painter's Tape
Paint Tray
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
IMPORTANT:
All flooring should be tested for adhesion
before coating the entire floor. Clean a small 3”x3”,
inconspicuous area, let dry. Apply base coat over area and
allow to dry for 12 hours. Take a utility knife and make an X
in the coating down to the flooring. Apply a 4” piece of duct
tape over the X and press firmly. Remove the tape with one
quick pull. If more than 10% of the coating comes off, the
floor will need to be sanded with 60-80 grit sandpaper
before coating the entire floor.
SURFACE PREPARATION
Rinse or sweep away any dirt and dust. Clean the entire
floor with a cleaner degreaser, such as Original Krud Kutter
®
Cleaner Degreaser, or provided cleaner.
Rinse thoroughly
and allow to dry completely. For any areas where caulk is
present, caulk needs to be removed before applying
coating. For waxed floors, wax needs to be removed before
applying coating.
NOTE: Failure to follow this preparation method may result
in poor adhesion and possible coating failure.
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
APPLICATION
Rust-Oleum
Home Base Coat is ready to use. Do not thin.
Stir thoroughly prior to use. If using more than one can of
Base Coat, intermix cans together for color uniformity.
Apply when air (ambient) temperature is 50-90°F (10-32°C)
and relative humidity is below 85%. Use a high quality
bristle brush or edger to trim the perimeter and hard-to-
reach areas. Use a long handled roller and a high-quality,
3/8” (Base Coat) and 1/4" (Top Coat) nap roller cover to
apply an even coat onto the surface.