Use and Care Manual

TECHNICAL DATA FDP-01
FLEXIDIP
™
REMOVABLE RUBBER COATING
Form: GDH-299
Rev.: 012715
1
.DESCRIPTION AND USES .
Rust-Oleum
®
FlexiDip
™
is an innovative, rubberized coating
designed for ultimate protection and customization with the
unique option for removal. The soft touch feature provides
additional comfort and grip. It is suitable for use on glass, metal,
plastic and more. This coating has been formulated for
temporary use and is recommended to be removed after 3
months or less.
.PRODUCTS .
SKU (11 ounce spray) Description
276289 Matte Black
276290 Matte White
276291 Matte Red
276292 Matte Dark Gray
283177 Grabber Green
283178 Bright Pink
283179 Graphite
283180 Matte Orange
283181 Cobalt Blue
..PRODUCT APPLICATION .
PAINTING CONDITIONS
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50-90°F (10-
32°C) and humidity is below 65% to ensure proper drying.
Do not apply to galvanized metal. Avoid spraying in very
windy and dusty conditions. Cover surrounding area to
protect from spray mist.
PRIMING
A primer is not required or recommended.
SURFACE PREPARATION
Wash the surface with a commercial detergent, or other
suitable cleaning method. Rinse with fresh water and dry
with a clean cloth. Remove loose paint and rust with a wire
brush or sandpaper. Lightly sand glossy surfaces.
WARNING: If you scrape, sand, or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.eps.gov/lead.
..PRODUCT APPLICATION (cont.) .
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Mask off the area to
be coated. Shake often during use. Hold can 8-12" from
surface and spray in a steady back-and-forth motion,
slightly overlapping each stroke. Keep the can the same
distance from the surface and in motion while spraying.
Apply 4 or more light coats to build desired coating
thickness, followed by 1 medium coat to achieve a smooth
final film. Allow the coating to dry to a matte finish (about 5
minutes) between coats. More coats will result in a thicker
coating which is easier to remove when desired. Allow the
coating to cure for 24 hours before washing. Remove tape
while the last coat is still wet. Do not use near open flame.
DRY & RECOAT
Dry and recoat times are based on 70°F (21°C) and 50%
relative humidity. Allow more time at cooler temperatures.
Dries to the touch in 20 minutes and can be handled in 1
hour. The film can be peeled off once the coating has fully
cured. Naphtha may assist in the removal of film in
intricate areas.
CLEAN-UP
When finished spraying, clear the spray valve by turning
can upside down and pushing the button for 5 seconds.
Allow wet paint to dry and once dry, peel away or clean up
wet paint with xylene or naphtha. Properly discard empty
container. Do not burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as xylene or naphtha. Do not insert any
object into can valve opening.