SDS

Date Printed: 12/10/2019
Isobutyl Methacrylate 97-86-9 5.0 N.E. N.E. N.E. N.E.
Mica 12001-26-2 5.0 3 mg/m3 N.E. N.E. N.E.
Stoddard Solvent 8052-41-3 5.0 100 ppm N.E. 500 ppm N.E.
Carbon Black 1333-86-4 5.0 3 mg/m3 N.E. 3.5 mg/m3 N.E.
Ethylbenzene 100-41-4 1.0 20 ppm N.E. 100 ppm N.E.
Solvent Naphtha, Light Aromatic 64742-95-6 1.0 N.E. N.E. N.E. N.E.
Butyl Methacrylate 97-88-1 1.0 N.E. N.E. N.E. N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use. A NIOSH/MSHA approved air purifying respirator with an organic
vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed
exposure limits.
Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any potential for an
uncontrolled release, exposure levels are not known, or in any other circumstances where air purifying respirators may not provide
adequate protection.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
Engineering Measures for Combustible Dust: No Information
9. Physical and Chemical Properties
Appearance:
Liquid
Physical State:
Liquid
Odor:
Solvent Like
Odor Threshold:
N.E.
Specific Gravity:
1.015
pH:
N.D.
Freeze Point, °C:
N.D.
Viscosity:
N.D.
Solubility in Water:
Negligible
Partition Coefficient, n-octanol/
water:
N.D.
Decompostion Temp., °C:
N.D.
Boiling Range, °C:
106 - 5,432
Explosive Limits, vol%:
0.6 - 8.0
Flammability:
Does not Support Combustion
Flash Point, °C:
13
Evaporation Rate:
Slower than Ether
Auto-ignition Temp., °C:
N.D.
Vapor Density:
Heavier than Air
Vapor Pressure:
N.D.
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid temperatures above 120°F (49°C). Avoid all possible sources of ignition. Flammable hydrogen gas
will evolve when product comes in contact with water or damp air. Heat will be generated. The amount of heat generated will depend
upon the volume of material in contact.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies.
HAZARDOUS DECOMPOSITION: By open flame, carbon monoxide and carbon dioxide. When heated to decomposition, it emits
acrid smoke and irritating fumes. Contains solvents which may form carbon monoxide, carbon dioxide, and formaldehyde.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions. May form peroxides of unkown stability.
11. Toxicological Information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Causes Serious Eye Irritation
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: May be absorbed through the skin in harmful amounts. Causes skin irritation.
Allergic reactions are possible.
EFFECTS OF OVEREXPOSURE - INHALATION: Harmful if inhaled. High gas, vapor, mist or dust concentrations may be harmful if
Page 4 / 7