SDS

Date Printed: 12/10/2019
Solvent Naphtha, Light Aromatic 64742-95-6 0.1-1.0 GHS07-GHS08 H304-332-340-350
Butyl Methacrylate 97-88-1 0.1-1.0 GHS02-GHS07 H226-315-317-319-332-335
4. First-Aid Measures
FIRST AID - EYE CONTACT: Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical
attention. Do NOT allow rubbing of eyes or keeping eyes closed.
FIRST AID - SKIN CONTACT: Wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation
develops or persists.
FIRST AID - INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get
immediate medical attention. Do NOT use mouth-to-mouth resuscitation. If you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
FIRST AID - INGESTION: Aspiration hazard: Do not induce vomiting or give anything by mouth because this material can enter the
lungs and cause severe lung damage. Get immediate medical attention. If swallowed, get medical attention.
5. Fire-Fighting Measures
EXTINGUISHING MEDIA: Alcohol Film Forming Foam, Carbon Dioxide, Dry Chemical, Dry Sand, Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS: Closed containers may explode when exposed to extreme heat due to buildup of
steam. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks and open flame. No unusual fire or explosion
hazards noted.
SPECIAL FIREFIGHTING PROCEDURES: Water may be used to cool closed containers to prevent pressure buildup and possible
autoignition or explosion. Evacuate area and fight fire from a safe distance. Use water spray to keep fire-exposed containers cool.
Containers may explode when heated.
Special Fire and Explosion Hazard (Combustible Dust): No Information
6. Accidental Release Measures
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition, ventilate area and remove with
inert absorbent and non-sparking tools. Dispose of according to local, state (provincial) and federal regulations. Do not incinerate
closed containers. Ventilate area, isolate spilled material, and remove with inert absorbent. Dispose of contaminated absorbent,
container, and unused contents in accordance with local, state, and federal regulations.
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Wash hands before eating. Remove contaminated clothing and launder before reuse.
Use only with adequate ventilation. Follow all SDS and label precautions even after container is emptied because it may retain
product residues. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.
STORAGE: Store in a dry, well ventilated place. Keep container tightly closed when not in use. Keep containers tightly closed.
Isolate from heat, electrical equipment, sparks and open flame. Do not store above 120 ° F. Store large quantities in buildings
designed and protected for storage of NFPA Class II combustible liquids. Keep away from heat, sparks, flame and sources of
ignition. Avoid excess heat. Product should be stored in tightly sealed containers and protected from heat, moisture, and foreign
materials.
Advice on Safe Handling of Combustible Dust: No Information
8. Exposure Controls / Personal Protection
Chemical Name CAS-No.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-TWA
OSHA PEL-
CEILING
1-Methoxy-2-Propyl Acetate 108-65-6 50.0 N.E. N.E. N.E. N.E.
Toluene 108-88-3 35.0 20 ppm N.E. 200 ppm 300 ppm
Titanium Dioxide 13463-67-7 20.0 10 mg/m3 N.E. 15 mg/m3 N.E.
Methyl Isobutyl Ketone 108-10-1 15.0 20 ppm 75 ppm 100 ppm N.E.
Hydrous Magnesium Silicate 14807-96-6 15.0 2 mg/m3 N.E. N.E. N.E.
Amorphous Silica 7631-86-9 5.0 N.E. N.E. 50 µg/m3 N.E.
Xylenes (o-, m-, p- isomers) 1330-20-7 5.0 100 ppm 150 ppm 100 ppm N.E.
Hydrotreated Light Distillate 64742-47-8 5.0 N.E. N.E. N.E. N.E.
Aluminum Flake 7429-90-5 5.0 1 mg/m3 N.E. 15 mg/m3 N.E.
Page 3 / 7