Use and Care Manual

ManualsBrandsRust-Oleum Automotive ManualsAutomotive Paint11 oz. Peel Coat Rugged Coat Silver Peelable Rubber Coating Spray Paint (6-Pack)

TECHNICAL DATA

PCG-08

PEEL COAT

RUGGED COAT

Form: GDH-1226

Rev.: 020519

DESCRIPTION AND USES

Rust-Oleum

Peel Coat

Rugged Coat is a textured,

removable coating that creates a rugged, exterior look and

protection from scratches and road debris. This premium

formula is easy to peel, safe to wash and can be applied to

metal, plastic, chrome, glass and other surfaces. Peel Coat is a

temporary coating that's designed to last for 6 months.

PRODUCTS

SKU

DESCRIPTION (Aerosol)

311281

Rugged Coat Black

311282

Rugged Coat Sand

311283

Rugged Coat Red

311284

Rugged Coat Blue

340541

Rugged Metallic Silver

PRODUCT APPLICATION

PAINTING CONDITIONS

Use outdoors or in a well ventilated area. Use when

temperature is between 50-90°F (10-32°C) and humidity is

below 65% to ensure proper drying. Do not apply to galvanized

metal. Avoid spraying in very windy and dusty conditions.

Cover surrounding area to protect from spray mist.

SURFACE PREPARATION

Wash the surface with a commercial detergent or soap and

water prior to the application

PRODUCT APPLICATION (cont.)

APPLICATION

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT STRIKE

CAN. Contact Rust-Oleum. Shake often during use. Hold can

14-20" from surface and spray in a steady back-and-forth

motion, slightly overlapping each stroke. Keep the can the

same distance from the surface and in motion while spraying.

Target 50% coverage on the first coat. Apply 4 or more light

coats to build desired coating thickness and ensure coats are

sufficiently dried before moving to the next maximize texture.

For best results, apply 1 more final coat using short burst

sprays. Allow coating to dry for about 10 minutes between

coats. More coats will result in a thicker coating which is easier

to remove when desired. Allow the coating to cure for 24 hours

before washing. Do not use near open flame.

DRY & RECOAT

Dry and recoat times are based on 70°F (21°C) and 50%

relative humidity. Allow more time at cooler temperatures. Lens

Tint dries to the touch in 20 minutes, to handle in 1 hour.

REMOVAL

The film can be peeled off once the coating has fully cured.

This coating has been formulated for temporary use and is

recommended to be removed within 6 months or less. A

microfiber cloth or mineral spirits may assist in the removal of

coating in intricate areas.

CLEAN-UP

When finished spraying, clear the spray valve by turning can

upside down and pushing the button for 5 seconds. Allow wet

paint to dry. Once dry, peel away or clean up with mineral

spirits. Properly discard empty container. Do not burn or place

in home trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object into

can valve opening.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA PCG-08 PEEL COAT® RUGGED COAT DESCRIPTION AND USES ® ® Rust-Oleum Peel Coat Rugged Coat is a textured, removable coating that creates a rugged, exterior look and protection from scratches and road debris. This premium formula is easy to peel, safe to wash and can be applied to metal, plastic, chrome, glass and other surfaces. Peel Coat is a temporary coating that's designed to last for 6 months.
PAGE 2
TECHNICAL DATA PCG-08 PEEL COAT® RUGGED COAT PHYSICAL PROPERTIES PEEL COAT RUGGED COAT Resin Type Synthetic Rubber Pigment Type Varies with color Solvents Blend of Acetates, Aliphatic and Aromatic Hydrocarbons MIR 1.60 Max Fill Weight 10 ounces Recommended Dry Film Thickness (DFT) Per Coat 0.5-1.0 mils (12.5-25µ) Practical Coverage at Recommended DFT Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity 8.0 sq.ft./can 2 (0.