SDS

Date Printed: 11/15/2018
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Contain spilled liquid with sand or earth. DO NOT use
combustible materials such as sawdust. Eliminate all ignition sources; use explosion-proof equipment. Place material in a container
and dispose of according to local, provincial, state and federal regulations. Remove all sources of ignition, ventilate area and remove
with inert absorbent and non-sparking tools. Dispose of according to local, state (provincial) and federal regulations. Do not
incinerate closed containers. Ventilate area, isolate spilled material, and remove with inert absorbent. Dispose of contaminated
absorbent, container, and unused contents in accordance with local, state, and federal regulations. Isolate the hazard area and deny
entry to unnecessary and unprotected personnel.
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Wash hands before eating. Use only with adequate ventilation. Follow all SDS and
label precautions even after container is emptied because it may retain product residues. Remove contaminated clothing and launder
before reuse. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.
STORAGE: Keep containers tightly closed. Isolate from heat, electrical equipment, sparks and open flame. Keep away from heat,
sparks, flame and sources of ignition. Keep container closed when not in use. Product should be stored in tightly sealed containers
and protected from heat, moisture, and foreign materials. Store in a dry, well ventilated place. Keep container tightly closed when not
in use. Avoid excess heat. Do not store above 120 ° F. Store large quantities in buildings designed and protected for storage of
NFPA Class II combustible liquids.
Advice on Safe Handling of Combustible Dust: No Information
8. Exposure Controls / Personal Protection
Chemical Name CAS-No.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-TWA
OSHA PEL-
CEILING
Acetone 67-64-1 90.0 250 ppm 500 ppm 1000 ppm N.E.
Octamethylcyclotetrasiloxane 556-67-2 10.0 N.E. N.E. N.E. N.E.
1-Chloro-4-(Trifluoromethyl)
Benzene
98-56-6 5.0 N.E. N.E. N.E. N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation. Use explosion-proof ventilation equipment. Provide general dilution of local exhaust ventilation in volume and pattern to
keep TLV of hazardous ingredients below acceptable limits.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use. A NIOSH/MSHA approved air purifying respirator with organic
vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed
exposure limits.
SKIN PROTECTION: Use impervious gloves to prevent skin contact and absorption of this material through the skin. Nitrile or
Neoprene gloves may afford adequate skin protection. Use gloves to prevent prolonged skin contact.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further information regarding personal
protective equipment and its application. Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
Engineering Measures for Combustible Dust: No Information
Page 3 / 6