SDS

Date Printed: 8/25/2016
8. Exposure Controls/Personal Protection
Chemical Name CAS-No.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-TWA
OSHA PEL-
CEILING
Hydrochloric Acid 7647-01-0 30.0 N.E. N.E. N.E. 5 ppm
Phosphoric Acid 7664-38-2 10.0 1 mg/m3 3 mg/m3 1 mg/m3 N.E.
Amines, Tallow Alkyl,
Ethoxylated
61791-26-2 10.0 N.E. N.E. N.E. N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Provide general dilution of local exhaust ventilation in volume and pattern to keep TLV of
hazardous ingredients below acceptable limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use. This material does not have established exposure limits. Wear a
positive pressure air-supplied respirator in situations where there may be potential for airborne exposure.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Use impervious gloves to prevent skin contact and absorption of
this material through the skin. Where contact is likely, wear chemical resistant gloves, a chemical suit, rubber boots and chemical
safety goggles plus a face shield. Nitrile or Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Where splashing is possible, full chemically resistant protective clothing (e.g acid suit) and
boots are required. Refer to safety supervisor or industrial hygienist for further guidance regarding types of personal protective
equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
9. Physical and Chemical Properties
Appearance:
Liquid
Physical State:
Liquid
Odor:
Solvent Like
Odor Threshold:
N.E.
Relative Density:
1.179
pH:
<1
Freeze Point, °C:
N.D.
Viscosity:
N.D.
Solubility in Water:
Miscible
Partition Coefficient, n-octanol/
water:
N.D.
Decompostion Temp., °C:
N.D.
Boiling Range, °C:
45 - 177
Explosive Limits, vol%:
N.A. - N.A.
Flammability:
Does not Support Combustion
Flash Point, °C:
94
Evaporation Rate:
Slower than Ether
Auto-ignition Temp., °C:
N.D.
Vapor Density:
Heavier than Air
Vapor Pressure:
N.D.
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid contact with strong acid and strong bases. Avoid contact with metals.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies. Avoid contact with water. Product
slowly corrodes copper, aluminum, zinc, and galvanized surfaces.
HAZARDOUS DECOMPOSITION: Decomposition produces hydrogen chloride, chlorine and hydrogen gases.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions.
11. Toxicological information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Substance causes severe eye irritation. Injury may be permanent. Corrosive.
Will cause eye burns and permanent tissue damage, including blindness.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Contact causes severe skin irritation and possible burns. Substance is
corrosive. Causes severe skin burns. Severely irritating; may cause permanent skin damage. Corrosive; causes skin burning.
EFFECTS OF OVEREXPOSURE - INHALATION: Harmful if inhaled. High gas, vapor, mist or dust concentrations may be harmful if
inhaled. Avoid breathing fumes, spray, vapors, or mist. High vapor concentrations are irritating to the eyes, nose, throat and lungs.
EFFECTS OF OVEREXPOSURE - INGESTION: Corrosive and may cause severe and permanent damage to mouth, throat and
Page 3 / 5