UNO-S2 Keypad Installation Manual
SAFETY INFORMATION UNO-S2 Keypad 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to. Follow Instructions - All operating and user instructions should be followed.
TABLE OF CONTENTS UNO-S2 Keypad Front Panel ..............................................................................................4-5 Operation ....................................................................................................6 User Menu ................................................................................................7-8 Settings ......................................................................................................9 Update Port .......................
USER GUIDE UNO-S2 Keypad Front Panel 1 7 2 6 3 5 4 4
USER GUIDE UNO-S2 Keypad Front Panel 1 LCD PANEL - 12-character backlit display shows status of the room, source, volume, and more 2 SOURCE SELECT BUTTON - Scrolls through the sources directly connected to the CAV6.6/CAM6.6. Press and hold brings up the USER MENU for Loudness, Bass, Treble, etc. 3 VOLUME UP/DOWN BUTTONS - Raises and lowers the volume for the room 4 IR RECEIVER - Receives IR signals and passes them to the controller and source equipment.
USER GUIDE UNO-S2 Keypad Operation 1 2 3 4 1 MODE: “DND”- Do Not Disturb “SHARED”- Same source selected in multiple rooms “SYS ON”- Indicates system on “PARTY”- Party Mode enabled “MASTER”- Master Keypad in Party Mode 6 2 12-character display 3 Volume Indicator 4 Indicates the middle of setting range / /
USER GUIDE UNO-S2 Keypad User Menu Zone On/Off Press and release to turn on the UNO System Keypad. This also turns on the corresponding CAV6.6/CAM6.6’s room, and any presets previously assigned will be activated, including settings for bass, volume, last source selected, etc. Press and release to turn off the UNO System Keypad. This will also put the corresponding CAV6.6/CAM6.6’s room into a standby state.
USER GUIDE UNO-S2 Keypad User Menu Next, press and hold the desired or button until SAVED is displayed on the LCD panel. Now a press and release of the button will recall the favorite preset. To set a favorite numbered disc or channel, use or to select a disc or channel (e.g., channel 45). Wait for the keypad to show the source name, then press and hold the F1 or F2 within 15 seconds of setting the numeric selection to save the setting.
USER GUIDE UNO-S2 Keypad Settings Feature and Setting: 1. BASS -10 < Bass:Flat > +10 2. TREBLE -10 < Treble:Flat > +10 3. LOUDNESS (more bass, fuller sound) On or Off 4. BALANCE Left -10 < Center > Right +10 5. TURN ON VOL (default room volume level) 0 to 100 room. Any keypad in the system can become a Master Keypad (if enabled) but only one Master Keypad may exist at a time in Party Mode.
INSTALLER GUIDE UNO-S2 Keypad Update Port 1 DATA RS-232 DATA RS-232 GND N/C +12VDC 2 10 1 SETUP BUTTON - Activates Installer Setup Mode for the UNO-S2 keypad 2 OS UPDATE PORT - Port used for UNO keypad OS software updates
INSTALLER GUIDE UNO-S2 Keypad Rear Panel 2 3 1 4 1 EXTERNAL IR RECEIVER IN CONNECTOR - Connection for external IR Receiver 2 OS UPDATE JUMPER - Selects “Run” or “OS Update” mode 3 RESET BUTTON - Reset whenever changing from RUN to OS update 4 110 PUNCHDOWN CONNECTOR - Termination for CAT-5 connection between the UNO-S2 Keypad and the CAV6.6/CAM6.
INSTALLER GUIDE UNO-S2 Keypad Connections Punchdown Tool Jumper Setting (back of keypad) Punchdown Tool CAT-5 Connections (back of keypad) OS Update Port (front of keypad) 12
INSTALLER GUIDE UNO-S2 Keypad Connections CAT-5 Connection The UNO-S2 Keypad uses a 110-punchdown terminal to provide a simple installation and strong connection for CAT-5 cable’s eight conductors. Punchdown terminals require the use of a punchdown tool which has been provided with the keypad kit. Attach the CAT-5 cable to the 110-punchdown terminal on the UNO-S2 Keypad as shown, matching the conductor colors to the connection color guide.
INSTALLER GUIDE UNO-S2 Keypad Diagnostics Menu 14 The Diagnostics Menu allows the installer to run a diagnostic check on the keypad and to verify the firmware version. The Diagnostics Menu also contains the update firmware procedure for updating the UNO-S2’s firmware. the display. The menus are outlined in the diagram on the next page.
INSTALLER GUIDE UNO-S2 Keypad Diagnostics Menu Press and Hold Setup Button DIAGNOSTICS CONTROLLR ID PORT ID KEYPAD ID Displays Controller ID number Displays Port ID number Displays Keypad ID number VERSION UPDATE FIRMW Displays current firmware version Hold PLAY After update cycle Power Start Update Cycle Power BUTTON TEST DISP CHAR DISP BLOCK DISP ROW Press button to be tested Press button to display character Press button to display blocks Press button to display rows BG COLOR Sele
INSTALLER GUIDE UNO-S2 Keypad Firmware Update Note: When a firmware update is released, it is available online at the Document Center on www.russound.com, in Technical Documents under Multi-zone products. The firmware update procedure may be modified, so always check for the latest version. Requirements: 1. PC computer running Windows 95, 98, ME, NT, 2000, XP operating system 2. Available DB-9 serial RS-232 data port (baud rate= 38400, data bits = 8, no parity, 1 stop bit, no flow control) 3.
INSTALLER GUIDE UNO-S2 Keypad Firmware Update Then press and hold the “Play” key for approximately 2 seconds until “Start Update” is displayed. Now the keypad is ready for update. Method B: Move the OS Update jumper on the rear panel of the keypad to the Update position (on both pins). Press the Reset button located next to the OS update jumper. At this point, the display will be backlit and blank but the buttons will be dark. Method A and B: Start the Flash Magic application.
INSTALLER GUIDE UNO-S2 Keypad Location Plastic Double-Gang Electrical Box (36 ci) UNO-S2 Back Plate Screw Screw Screwless Cover Plate 18
INSTALLER GUIDE UNO-S2 Keypad Location Installation Location The best infrared remote performance is achieved with the keypad installed away from any direct sunlight, plasma TV, and low voltage lighting controls. Also consider convenience when choosing a location. Choose a place that is easily seen from the position where a person is most likely to be located. Check whether or not you can route the wire to the location you have chosen. Keypad Installation Route CAT-5 wire to the junction box from the CAV6.
INSTALLER GUIDE IR Receiver Connection Back of UNO-S2 Back of Russound 858 DO NOT CONNECT SHIELD 20 The UNO-S2 keypad has an EXTERNAL IR RECEIVER IN terminal for connecting an external IR Receiver such as the Russound 858, SaphIR 862 Eye, or SaphIR 860 Phantom. Use 2 twisted pair wire with one pair connecting GND (GROUND) and IR (SIGNAL) and the other pair connecting ST (STATUS) and V+ (+12VDC). Connect the shield or drain to ground at the UNO-S2 only.
TECHNICAL SPECIFICATIONS UNO-S2 Keypad Specifications Dimensions: Weight: 3.65"W x 1.125"D x 4.3"H (9.2 x 10.9 x 2.8 cm) Fits 2-Gang UL/CSA Approved Work Box 9 oz. (255 g) Power Requirements: 12 VDC 180mA CAT-5 Connection: 110 punchdown All trademarks are the property of their respective owners.
WARRANTY Warranty Repair The Russound UNO-S2 is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. For this warranty to apply, the unit must be installed and used according to its written instructions. If service is necessary, it must be performed by Russound.
WARRANTY Russound sells products only through authorized Dealers and Distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void the warranty on the applicable product.
Russound 5 Forbes Road, Newmarket, NH 03857 tel 603.659.5170 • fax 603.659.5388 e-mail: tech@russound.com www.russound.com 28-1141 Rev.
