SaphIR™ K2 Keypad Instruction Manual
SAFETY PRECAUTIONS For your safety, please read and follow these precautions before installing or using this product: ➤ Ground device properly. Make sure the device’s means of ➤ Read instructions. Read and understand all the applicable ➤ Keep device clean. From time to time, wipe off the device instructions before installing or operating the device. ➤ Retain documents. Keep this manual in a convenient place for reference. ➤ Heed warnings.
TABLE OF CONTENTS USER SECTION Introduction Features and Key Guide Optional SRC1 Basic Remote Control Optional SRC2 Advanced Learning Remote Control Keypad Operation INSTALLER SECTION Getting Started Installation Overview Terms You Need to Know Typical System Configuration Keypad Installation Keypad Connections EZB-1SC Connection Details Multiple 857 Connections Programming Port Programming Overview Programming Instructions PROGRAMMING MENU Navigation Programming Menu Top Level AMP/RECEIVER SETUP MENU Amp/
USER Introduction Product Overview Features Thank you for choosing the Russound SaphIR™ K2 keypad. The K2 is an in-wall programmable IR keypad that works like a universal remote to provide complete control of your audio and video components. It contains an extensive library of IR codes to select discs, tracks, channels, volume, and other settings for most audio and video components. It can also learn IR commands for components and other devices not in the library.
USER Features and Key Guide 1 7 2 6 3 5 4 1 DISPLAY – 12-character backlit LCD panel shows source name and other information 2 SOURCE SELECT KEY – Selects the desired source connected to the amp/receiver 3 VOLUME UP/DOWN KEYS – Control the volume of the amp/receiver 4 IR SENSOR – Receives IR signals from a remote control for operating the K2 Keypad and the source equipment 5 COMMAND KEYS – Control the source equipment 6 POWER KEY – Turns keypad on or off when pressed once; turns all keypads
USER Optional SRC1 Basic Remote Control 1 1 POWER KEY – Turns the keypad on and off. Press and hold for All On or All Off function. 2 NUMERIC KEYS – For direct selection of channels or tracks. 3 VOLUME UP/DOWN KEY – Raises and lowers the amp/receiver volume. 4 COMMAND KEYS – Control the source equipment. 5 DIRECT SOURCE SELECT KEYS – Directly select sources 1– 6 controlled by the keypad. 6 F1 AND F2 KEYS – Set and select Favorite 1 and Favorite 2 presets.
USER Optional SRC2 Advanced Learning Remote Control 1 1 POWER KEY – Turns the keypad on and off while in System mode. Press and hold for All On or All Off function. 2 SYSTEM MODE KEY – Selects System mode to control the SaphIR K2 keypad and connected sources. The remote must be in System mode to work with the SaphIR K2 keypad. 3 NUMERIC KEYS – For direct selection of channels or tracks. 4 VOLUME UP/DOWN KEY – Raises and lowers the amp/receiver volume. 5 COMMAND KEYS – Control the source equipment.
USER Keypad Operation On/Off Press and release turn off. If power management is set up on your keypad, to turn on the K2 keypad. This will also activate any speakers wired through the speak- source components. er relay on the back of the K2. If power management is System On Indicator set up on your keypad, turning on the keypad will also When a keypad is off but the connected audio system is turn on your amp/receiver and source components.
USER Keypad Operation F1 and F2 Keys The and source at the K2 Keypad. The command keys are actipreset keys are for saving and recall- vated with a press and release, or with a press and hold ing a source selection and favorite disk or channel. to access secondary functions. To save a preset, first select a source. Next, press and User Menu hold the The User Menu allows you to adjust the keypad back- or key until SAVED appears on the dis- play. This saves the source selection.
INSTALLER Getting Started About this Section Terms You Need to Know The rest of this manual provides technical information for installing and programming the SaphIR K2 keypad. This section is intended mostly for installers, but users may find the information useful as well. Amp/Receiver – The central receiver, preamplifier, or amplifier to which the source components in the audio system are connected.
INSTALLER Getting Started web site and uploaded into the keypad by using the Firmware Update procedure in the System Menu. This requires connecting a computer to the keypad with a Programming Cable, part number 2500-121036. Input Order – The order in which the amp/receiver selects its source inputs. By default, the K2 keypad selects Input 1 for Source 1, Input 2 for Source 2, etc. You can change this order through the Amp/Receiver Key Configuration Procedure.
INSTALLER Getting Started The Russound 1201A power supply for the 857 supports a maximum of four K2 keypads. If the installation includes more than one K2 keypad, you can tie them together with a Russound EZB-1SC connecting block. The EZB-1SC is a parallel wiring device for speakers or IR data and power. This makes it a convenient point for connecting more than one K2 keypad. Multiple arrangements can be linked together with successive 857s for increased capacity.
INSTALLER Keypad Installation Tools Needed for Installation Considerations • Drill with a 1⁄2-inch drill bit • For best infrared remote performance, locate the keypad away from direct sunlight, plasma TVs, lighting controls, and high- and low-voltage wiring. Also consider convenience when choosing a location. • Keyhole saw • Flat-head screwdriver (medium size) • Stud finder • When running cables, avoid locations concealing pipes, heating ducts and AC wiring in the general vicinity.
INSTALLER Keypad Connections IR and Power Connections 1 The K2 keypad can be connected using either CAT-5 or shielded 4conductor, 22-gauge 2-twisted-pair cable. The maximum recommended cable length is 250 feet for either type of cable. See page 15 for the wiring color codes for both cables. 2 +12VDC 200mA 4 IN Shielded 22/4 Connection at K2 Stand Alone IR Keypad • When using CAT-5 cable, do not connect the Orange/White and Green/White to GND (ground) at the K2 keypad.
INSTALLER EZB-1SC Connections EZB-1SC Connection Details Top View EZB-1SC Shielded 22/4 Cable Wire Color Red Black Green White Bare Shielded 22/4 Connection to EZB-1SC Snap Connector Side View Function +12V Ground IR Signal Status Drain (Gnd) Note: To ensure proper operation, it’s important to maintain similar wiring schemes at all termination points of the EZB-1SC.
INSTALLER Multiple 857 Connections To SaphIR K2 keypads Multiple 857 Connections Multiple groups of up to four K2 keypads can be linked together by using successive Russound 857 IR connecting blocks as shown in the diagram to the left. Each IR connecting block must have its own 1201A power supply. Each Russound 1201A power supply supports a maximum of four K2 keypads. When using shielded 22/4 cable, use one twisted pair for power and ground, and the other twisted pair for status and IR signal.
INSTALLER Multiple 857 Connections Note: Do not connect the +12VDC wire between the 857 connecting blocks. Each 857 requires its own 1201A power supply. Only GND, SIGNAL and STATUS need to be connected between multiple connecting blocks. Source IR emitters can be connected to any connecting block in this arrangement.
INSTALLER Programming Port Programming Port 1 DATA Keypad Programming DATA The SaphIR K2 can be programmed by using Russound’s free EZpro software on a computer. You can download EZpro from the Infrared Products page in the Document Center at www.russound.com. GND +12VDC 3 2 The Programming Port is used for programming the SaphIR K2, backing up the keypad configuration, and updating the keypad firmware with a Windows-based computer.
INSTALLER Programming Overview Programming Methods There are two ways to program the SaphIR K2 keypad. The easier method is to use EZpro software on a connected Windows-based computer, but you can also program the keypad manually using the programming menu described in this section. The menu is organized in a file tree structure similar to that found on a computer. At each subsequent level, options become more specific.
INSTALLER Programming Overview Recommended Process It will be much easier to program the SaphIR K2 if you follow the steps in a particular order, especially if you’re programming it manually. Here’s the order we recommend for initial setup: 1. 2. 3. 4. 5. 20 Component Control – First learn how the amp/receiver and source components work with their remote controls, especially how source inputs are numbered on the amp/ receiver.
INSTALLER Programming Overview 11. Amp/Receiver Key Configuration (page 24) – By default, the Source key selects sources and the Volume keys adjust the output volume of the amp/receiver. You may wish to reconfigure these keys to perform alternate functions. The Amp/Receiver Key Configuration procedure allows you to do this. 12. Source Command Key Configuration (page 30) – This procedure allows you to assign additional or alternate functions to the seven command keys on the SaphIR K2 keypad for any source.
INSTALLER Programming Menu Instructions PROGRAMMING MENU The Programming Menu has various levels and consists of submenus, procedures, and features. A procedure is a guided sequence of steps to set feature parameters, such as selecting source names. Once you begin a procedure, the system prompts for the information needed at each step. A feature is a setting for which you must choose a parameter. Together, the feature parameters make up the system configuration.
INSTALLER Programming Menu Instructions The following sections describe the menus, procedures, and features. They are presented in the order we recommend for manually programming the keypad (when not using SaphIR EZpro software). The flow charts on pages 43–53 are shown in the same order. Programming Menu Top Level Press the Setup SOURCE SETUP button to enter the Programming Menu.
INSTALLER Programming Menu Instructions Amp/Receiver Basic Setup Procedure (continued) and the amp/receiver and turn it and all sources on. Also make sure you can control the amp/receiver with its remote control aimed at the SaphIR K2 keypad in normal operating mode. See Amp/Receiver Basic Setup Procedure flow chart on page 43. To begin the Amp/Receiver Basic Setup Procedure, select BASIC SETUP from the Amp/Receiver Setup Menu and press Play 1.
INSTALLER Programming Menu Instructions To begin the Amp/Receiver Key Configuration Procedure, select KEY CONFIG from the Amp/Receiver Setup Menu and press 1. 2. SELECT A KEY – Press to select a key to be configured. Press to enter your selection. COMMAND TYPE – Select and enter the type of command. Choose one of the following options: a. Select and enter Default to use the same command type previously selected in BASIC SETUP. i. b. c. d.
INSTALLER Programming Menu Instructions Learn IR Procedure (continued) These locations are called Learned Sources. Learned commands can be assigned in other procedures by selecting Learned IR as a command type and then selecting the corresponding Learned Source label. See Learn IR Procedure flow chart on page 45. To begin the Learn IR Procedure, select LEARN IR from the top level of the Programming Menu and press Play .
INSTALLER Programming Menu Instructions 4. TEST IR? – Select and enter Yes or No. Entering Yes sends the learned command to the device to test the IR. If the device responds, the IR learning was a success. If the device does not respond, either the keypad did not properly learn the command or the command is inappropriate for the device. Entering No returns the procedure to LEARNED SRC (step 1). 5. SUCCESS? – Select and enter Yes if the IR learning was successful.
INSTALLER Programming Menu Instructions Number of Sources Feature (continued) To enter the Number of Sources Feature, select SOURCE SETUP from the top level of the Programming Menu and press Play At BASIC SETUP, press Previous once. At # OF SOURCES, press Play Using the Plus or Minus Press the Setup button to return to the top level of the Programming Menu. . . key, scroll through the numbers (1–8) to select the number of sources and then press Play .
INSTALLER Programming Menu Instructions a. Select and enter a specific device (e.g., DVD, Video Acc, Tuner/Amp) to use an IR device code from the built-in library. i. DEVICE CODE – Select and enter the source’s IR device code number from the Reference section of this manual. ii. TEST IR? – Select and enter Yes to send a power command to the source to test IR operation. Select and enter No to skip the test. A. b. c. 4.
INSTALLER Programming Menu Instructions Source Command Key Configuration Procedure (Optional) This procedure allows you to redefine command key functions for each source. Each of the seven command keys can be customized for two functions: a “press” function and a “press-and-hold” function. For example, since there is no Eject key on the keypad, you can assign an eject function to a press-and-hold operation of the Stop key for a CD player.
INSTALLER Programming Menu Instructions c. Select and enter Macro to configure the key with a macro. (To build macros, see Macro Editor Procedure on page 38.) i. d. 6. MACRO ID – Select and enter the macro ID number. Select and enter Unassigned to clear the key configuration. Any custom settings for that key will be erased. SAVE CHANGES? – Select and enter Yes to save changes. Procedure returns to SOURCE NUM (step 1). Press the Setup button to back out of the procedure.
INSTALLER Programming Menu Instructions Numeric IR Procedure (Optional) This procedure allows you to program source-specific numeric control functions (e.g., Channel 12, Disk 89) by enabling the Plus and Minus keys to scroll through channel or disk numbers. The procedure also allows the programming of prefix and suffix commands. Some source numeric commands require a prefix command such as Channel for a tuner or Disc for a CD changer, or a suffix command such as Enter or Play.
INSTALLER Programming Menu Instructions B. iii. iv. Select and enter a specific device (e.g., CD, TV) to use an IR device code from the built-in library. A. DEVICE CODE – Select and enter the IR device code number from the Reference section of this manual. B. KEY FUNCTION – Select and enter the function you want the prefix command to perform (e.g., Disc, Channel, Preset). Select and enter Macro to configure the prefix command with a macro. (To build macros, see Macro Editor Procedure on page 38.) A.
INSTALLER Programming Menu Instructions Numeric IR Procedure (continued) iv. A. DEVICE CODE – Select and enter the IR device code number from the Reference section of this manual. B. KEY FUNCTION – Select and enter the function you want the suffix command to perform (e.g., Enter, Play). Select and enter Macro to configure the suffix command with a macro. (To build macros, see Macro Editor Procedure on page 38.) Procedure advances to MACRO ID. A. v. 7. MACRO ID – Select and enter the macro ID number.
INSTALLER Programming Menu Instructions a. Select and enter Default to use the same command type previously selected for the source in BASIC SETUP. b. Select and enter Learned IR to use a particular learned IR command not included in the default command type. (See Learn IR Procedure on page 25.) c. d. i. LEARNED SRC – Select and enter the Learned Source location assigned to the device. ii. KEY FUNCTION – Select and enter the function you want the source select command to perform (e.g.
INSTALLER Programming Menu Instructions Power Management Procedure (continued) You can also verify the power state of the amp/receiver by obtaining a status voltage from a 12 VDC trigger output on the device or from a 12 VDC power supply plugged into its switched AC receptacle (see system diagram on page 12). This is useful when the amp/receiver doesn’t use discrete On and Off commands but toggles on and off with the same Power command.
INSTALLER Programming Menu Instructions A. v. 3. Select and enter Unassigned to clear the Power On command. POWER OFF CMD – Select and enter Yes to program a Power Off command or macro. Select and enter No to disable the Power Off command or macro and skip to SAVE CHANGES (step 4). a. COMMAND TYPE – Select and enter a command type for the amp/receiver or other device you want to power manage. Choose one of the following options: i.
INSTALLER Programming Menu Instructions Macro Editor Procedure (Optional) This procedure allows you to create a sequence of commands that are launched with one key touch or other event. For example, you can create a macro to lower a motorized screen and set the receiver in surround mode when you press the Play key when a DVD player is selected as the source.
INSTALLER Programming Menu Instructions d. i. DEVICE CODE – Select and enter the IR device code number from the Reference section of this manual. ii. KEY FUNCTION – Select and enter the function you want the command to perform (e.g., Play). Procedure returns to COMMAND NUM (step 3). Select and enter Macro if you want this command to run a separate macro. i. e. Select and enter Delay to postpone delivery of the next command in the macro. i. f. MACRO ID – Select and enter the macro ID number.
INSTALLER Programming Menu Instructions SYSTEM MENU The System Menu contains items that allow you to obtain information about the keypad and perform various utilities. To enter the System Menu, select SYSTEM from the top level of the Programming Menu and press Play following procedures: KEYPAD ID COPY CONFIG SYS INFO UPDATE FIRMW FACTORY INIT .
INSTALLER Programming Menu Instructions 3. LOOKING FOR... – The sending keypad looks for the keypad(s) to copy to. When the sending keypad locates the receiving keypad(s), RDY TO RECEIVE appears on the receiving keypad(s). If a receiving keypad is not located, NOT FOUND appears on the sending keypad. 4. SENDING DATA – Once the sending keypad has located the receiving keypad(s), SENDING DATA appears on its display along with a receiving keypad’s ID.
INSTALLER Programming Menu Instructions Update Firmware Procedure (Optional) This procedure allows you to update the SaphIR K2’s firmware from a computer using a Russound Programming Cable (part number 2500-121036) connected to the programming port on the side of the keypad (see diagram on page 18). Updates and instructions are made available in the Document Center at www.russound.com. See System Menu flow chart on page 53.
INSTALLER Programming Flow Charts AMP/RCVR Setup - Basic Setup Procedure Press and Release Setup Button For instructions, see page 23 Setup button on right side of keypad under cover plate SOURCE SETUP Menu AMP/RCVR SETUP Menu POWER MGT Procedure LEARN IR Procedure BASIC SETUP Procedure KEY CONFIG Procedure AMP/RCVR Setup Enter menu/Up one level Next item MACRO EDITOR Procedure Previous item SYSTEM Menu Installation Menu Select parameter Enter 43
INSTALLER Programming Flow Charts AMP/RCVR Setup - Key Configuration Procedure Press and Release Setup Button For instructions, see page 24 Setup button on right side of keypad under cover plate 44 SOURCE SETUP Menu AMP/RCVR SETUP Menu POWER MGT Procedure BASIC SETUP Procedure KEY CONFIG Procedure AMP/RCVR Setup Enter menu/Up one level LEARN IR Procedure Next item MACRO EDITOR Procedure Previous item SYSTEM Menu Select parameter Installation Menu Enter
INSTALLER Programming Flow Charts Learn IR Procedure Press and Release Setup Button For instructions, see page 25 Setup button on right side of keypad under cover plate SOURCE SETUP Menu AMP/RCVR SETUP Menu POWER MGT Procedure LEARN IR Procedure MACRO EDITOR Procedure SYSTEM Menu Learn IR Menu Red LED on right side of UNO-IR2 blinks rapidly Transmit IR remote into UNO-IR2 receiver diode Enter menu/Up one level Next item Previous item Select parameter Enter 45
INSTALLER Programming Flow Charts Press and Release Setup Button Source Setup - Basic Setup Procedure For instructions, see page 28 Setup button on right side of keypad under cover plate SOURCE SETUP Menu AMP/RCVR SETUP Menu BASIC SETUP Procedure KEY CONFIG Procedure POWER MGT Procedure SOURCE NAMES Procedure LEARN IR Procedure NUMERIC IR Procedure Enter menu/Up one level 46 MACRO EDITOR Procedure SRC SEL CMD Procedure Next item SYSTEM Menu # OF SOURCES Feature Previous item Installation
INSTALLER Programming Flow Charts Source Setup - Key Configuration Procedure Press and Release Setup Button For instructions, see page 30 Setup button on right side of keypad under cover plate SOURCE SETUP Menu AMP/RCVR SETUP Menu BASIC SETUP Procedure KEY CONFIG Procedure POWER MGT Procedure SOURCE NAMES Procedure LEARN IR Procedure MACRO EDITOR Procedure SYSTEM Menu NUMERIC IR Procedure SRC SEL CMD Procedure # OF SOURCES Feature Enter menu/Up one level Next item Previous item Installati
INSTALLER Programming Flow Charts Press and Release Setup Button Source Setup - Source Names Procedure For instructions, see page 31 Setup button on right side of keypad under cover plate SOURCE SETUP Menu AMP/RCVR SETUP Menu BASIC SETUP Procedure KEY CONFIG Procedure Enter menu/Up one level 48 POWER MGT Procedure SOURCE NAMES Procedure Next item LEARN IR Procedure NUMERIC IR Procedure Previous item MACRO EDITOR Procedure SRC SEL CMD Procedure SYSTEM Menu # OF SOURCES Feature Select parame
INSTALLER Programming Flow Charts Press and Release Setup Button Source Setup - Numeric IR Procedure For instructions, see page 32 Setup button on right side of keypad under cover plate SOURCE SETUP Menu AMP/RCVR SETUP Menu BASIC SETUP Procedure KEY CONFIG Procedure POWER MGT Procedure SOURCE NAMES Procedure MACRO Enter menu/Up one level LEARN IR Procedure MACRO EDITOR Procedure SYSTEM Menu NUMERIC IR Procedure SRC SEL CMD Procedure # OF SOURCES Feature Installation Menu Source Setup Menu
INSTALLER Programming Flow Charts Source Setup - Source Select Command and # of Sources Procedures Press and Release Setup Button For instructions, see pages 34 and 27 Setup button on right side of keypad under cover plate 50 POWER MGT Procedure SOURCE SETUP Menu AMP/RCVR SETUP Menu BASIC SETUP Procedure KEY CONFIG Procedure SOURCE NAMES Procedure Enter menu/Up one level Next item LEARN IR Procedure MACRO EDITOR Procedure SYSTEM Menu Installation Menu Source Setup Menu NUMERIC IR Procedur
INSTALLER Programming Flow Charts Power Management Procedure Press and Release Setup Button For instructions, see page 35 Setup button on right side of keypad under cover plate SOURCE SETUP Menu USE STATUS AMP/RCVR SETUP Menu POWER MGT Procedure LEARN IR Procedure MACRO EDITOR Procedure SYSTEM Menu Power MGT Menu ON Enter menu/Up one level Next item Previous item Select parameter Enter 51
INSTALLER Programming Flow Charts Macro Editor Procedure Press and Release Setup Button For instructions, see page 38 Setup button on right side of keypad under cover plate SOURCE SETUP Menu AMP/RCVR SETUP Menu POWER MGT Procedure Enter menu/Up one level 52 LEARN IR Procedure Next item MACRO EDITOR Procedure Previous item SYSTEM Menu Select parameter Macro Editor Menu Enter
INSTALLER Programming Flow Charts System Menu Press and Release Setup Button For instructions, see page 40 Setup button on right side of keypad under cover plate SOURCE SETUP Menu AMP/RCVR SETUP Menu POWER MGT Procedure LEARN IR Procedure MACRO EDITOR Procedure KEYPAD ID Procedure COPY CONFIG Procedure SYSTEM INFO Procedure UPDATE FIRMWARE Procedure FACTORY INIT Procedure COPY TO...
REFERENCE Source Information Form Sample Source Information Form AMP/RCVR K2 Amp/Rcvr Source Input # 2 1 N/A Enter which Amp/Rcvr input connection the source is plugged into. This info is used when performing the Amp/Rcvr Setup procedure. Select the name for the Source from the Source Names List Page 48. Source Name CD Player 1 Tuner N/A Manufacturer Pioneer Sony Sony Model # PD-F908 STR-DE985 STR-DE985 Enter the model # of the source component here.
REFERENCE Source Information Form Source Information Form 7 K2 8 AMP/RCVR Amp/Rcvr Source Input # N/A Source Name N/A Manufacturer Model # IR Command Type IR Device Code (4-digit or Learned Source #) Numeric IR Y or N Y or N Y or N Y or N Y or N Y or N Y or N Y or N Highest # Auto Play N/A N/A Y or N Y or N Y or N Y or N Y or N Y or N Y or N Y or N N/A 55
REFERENCE Source Names 56 Aux 1 Dance Music Mini Disk Tuner 1 CustomName4 Aux 2 Digtl Cable Mood Music Tuner 2 CustomName5 Aux DSS Receiver MorningMusic Tuner 3 CustomName6 Blues DSS 1 MP3 Tuner CustomName7 Cable 1 DSS 2 Oldies TV CustomName8 Cable 2 DSS 3 Pop VCR CustomName9 Cable 3 DVD Changer Rear Door VCR 1 CustomName10 Cable DVD Changr 1 Religious VCR 2 Sat Radio CD Changer DVD Changr 2 ReplayTV Source 1 (()) CD Changer 1 DVD Changr 3 Rock Source 2
REFERENCE IR Device Codes Device Codes for TVs: AOC Admiral Advent Aiko Aiwa Akai Alaron America Action Ampro Anam Apex Digital Audiovox Baysonic Belcor Bell & Howell Bradford Brockwood Broksonic CXC Candle Carnivale Carver Celebrity Changhong Cineral Citizen Concerto Contec Craig Crosley Crown Curtis Mathes Daewoo Daytron Denon Dumont Dwin 0030, 0019 0093, 0463 0761 0092 0701 0030 0179 0180 0751 0180 0748, 0765, 0767 0451, 0180, 0092, 0623 0180 0019 0154, 0016 0180 0019 0236, 0463 0180 0030, 0056 0030 00
REFERENCE IR Device Codes Sansui Sanyo Scimitsu Scotch Scott Sears 0463 0154 0019 0178 0236, 0180, 0178, 0179, 0019 0047, 0747, 0054, 0154, 0156, 0178, 0179, 0056, 0171 Semivox 0180 Semp 0156 Sharp 0093, 0688, 0689 Shogun 0019 Signature 0016 Sony 0000, 1100 Soundesign 0180, 0178, 0179 Squareview 0171 Starlite 0180 Supreme 0000 Sylvania 0054, 0030, 0171 Symphonic 0171, 0180 TMK 0178, 0056 TNCi 0017 Tandy 0093 Technics 0051, 0250 Technol Ace 0179 Techwood 0051, 0056 Teknika 0054, 0180, 0150, 0060, 0179, 0056
REFERENCE IR Device Codes Device Codes for VCRs: Admiral Adventura Aiko Aiwa Akai America Action American High Asha Audiovox Beaumark Bell & Howell Broksonic CCE Calix Canon Carver Cineral Citizen Colt Craig Curtis Mathes Cybernex Daewoo Denon Dynatech Electrohome Electrophonic Emerex Emerson Fisher Fuji Funai GE Garrard Go Video GoldStar Gradiente 0048, 0209 0000 0278 0037, 0000 0041 0278 0035 0240 0037 0240 0104 0184, 0121, 0209, 0002, 0479 0072, 0278 0037 0035 0081 0278 0037, 0278, 1278 0072 0037, 0047,
REFERENCE IR Device Codes Teac Technics Teknika Thomas Tivo Toshiba Totevision Unitech Vector Vector Research Video Concepts Videomagic Videosonic Villain Wards 0000, 0041 0035, 0162 0035, 0037, 0000 0000 0618, 0636 0045, 0043, 0845 0037, 0240 0240 0045 0038 0045 0037 0240 0000 0035, 0060, 0760, 0048, 0047, 0081, 0000, 0042, 0240, 0072, 0149 White Westinghouse 0209, 0072, 0278, 1278 XR-1000 0035, 0000, 0072 Yamaha 0038 Zenith 0039, 0000, 0209, 0479, 1479 Device Codes for Laser Disc Players: Aiwa Denon Fun
REFERENCE IR Device Codes Quasar RCA Samsung Sansui Sherwood Sony Stereophonics Sunfire Technics Thorens Venturer Victor Wards Yamaha 0039 1023, 1254, 0531, 1390, 1609 1295 1089 1653 1058, 1158, 1258, 0158 1023 1313 1308, 1309, 1518, 0039 1189 1390 0074 0014, 0158 0176, 1176 Device Codes for Amp and Misc.
REFERENCE Key Functions KEY FUNCTION TV CABLE VIDEO ACCESSORY SAT/DSS POWER ON OFF CHANNEL UP CHANNEL DOWN VOLUME UP VOLUME DOWN MUTE 1 2 3 4 5 6 7 8 9 0 ENTER +10/100 PREVIOUS CHANNEL INPUT EXTERNAL SOURCE PLAY STOP PAUSE SEARCH REVERSE SEARCH FORWARD RECORD TRACK FWD TRACK REVERSE LIVE/INTRO MENU SETUP MENU GUIDE EXIT Power On/Off On, Power On/Off Off, Power On/Off Channel Up Channel Down Volume Up Volume Down Mute Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Digit 7 Digit 8 Digit 9 Digit 0 Channe
REFERENCE Key Functions KEY FUNCTION TV CABLE VIDEO ACCESSORY SAT/DSS BACK MENU UP MENU DOWN MENU LEFT MENU RIGHT SELECT DISK UP DISK DOWN FAVORITE CHANNEL DISPLAY DISPLAY FORMAT SAP SURROUND ON/OFF SLOW OPEN/CLOSE RANDOM PIP ON PIP OFF PIP FREEZE PIP SWAP PIP MOVE PIP INPUT PIP CHANNEL UP PIP CHANNEL DOWN PIP MULTI INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT 6 INPUT 7 INPUT 8 INPUT 9 INPUT 10 SLEEP Back Menu Up, Adjust Up Menu Down, Adjust Dn Menu Left Menu Right Menu Select Adjust Up Adjust Down Fa
REFERENCE Key Functions KEY FUNCTION VCR LASER DISK DVD TUNER/AMP POWER ON OFF CHANNEL UP CHANNEL DOWN VOLUME UP VOLUME DOWN MUTE 1 2 3 4 5 6 7 8 9 0 ENTER +10/100 PREVIOUS CHANNEL INPUT EXTERNAL SOURCE PLAY STOP PAUSE SEARCH REVERSE SEARCH FORWARD RECORD TRACK FWD TRACK REVERSE LIVE/INTRO MENU SETUP MENU GUIDE EXIT Power On/Off On, Power On/Off Off, Power On/Off Channel Up Channel Down Volume Up Volume Down Mute Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Digit 7 Digit 8 Digit 9 Digit 0 Channel E
REFERENCE Key Functions KEY FUNCTION VCR LASER DISK DVD TUNER/AMP BACK MENU UP MENU DOWN MENU LEFT MENU RIGHT SELECT DISK UP DISK DOWN FAVORITE CHANNEL DISPLAY DISPLAY FORMAT SAP SURROUND ON/OFF SLOW OPEN/CLOSE RANDOM PIP ON PIP OFF PIP FREEZE PIP SWAP PIP MOVE PIP INPUT PIP CHANNEL UP PIP CHANNEL DOWN PIP MULTI INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT 6 INPUT 7 INPUT 8 INPUT 9 INPUT 10 SLEEP Clear Menu Up Menu Down Menu Left Menu Right Menu Select Thumbs Up Thumbs Down Replay Zones, Index Mark D
REFERENCE Key Functions KEY FUNCTION AMP/MISC. AUDIO CD HOME CONTROL POWER ON OFF CHANNEL UP CHANNEL DOWN VOLUME UP VOLUME DOWN MUTE 1 2 3 4 5 6 7 8 9 0 ENTER +10/100 PREVIOUS CHANNEL INPUT EXTERNAL SOURCE PLAY STOP PAUSE SEARCH REVERSE SEARCH FORWARD RECORD TRACK FWD TRACK REVERSE LIVE/INTRO MENU SETUP MENU GUIDE EXIT Power On/Off On, Power On/Off Off, Power On/Off Preset Up Preset Down Volume Up Volume Down Mute Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Digit 7 Digit 8 Digit 9 Digit 0 5.
REFERENCE Key Functions KEY FUNCTION AMP/MISC.
REFERENCE Technical Specifications and Certifications Technical Specifications Display: Backlight: A-V device control: IR control: Macro capability: Speaker relay capacity: Power requirement: System cabling: Maximum cable run: Wall plate dimensions: In-wall dimensions: Weight: 68 12-character LCD Selectable amber or green 8 sources plus receiver or amplifier Preprogrammed library of device codes Built-in IR sensor with pass-through Up to 132 10-step macros 30 watts per channel RMS continuous, 100 watts p
REFERENCE Warranty Warranty The Russound SaphIR K2 is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. For this warranty to apply, the unit must be installed and used according to its written instructions. If service is necessary, it must be performed by Russound.
NOTES 70
NOTES 71
SaphIR™ K2 Keypad Programmable Infrared Control Instruction Manual Russound 5 Forbes Road, Newmarket NH 03857 USA Voice: 603.659.5170 • Fax: 603.659.5388 www.russound.com Technical Support: tech@russound.
