CAM6.
IMPORTANT SAFEGUARDS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. 10.Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 11.Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12.
TABLE OF CONTENTS USER SECTION Product Introduction ............................................................................................................6 Component Guide CAM6.6 Controller...............................................................................................................7 UNO-S1 Keypad ..................................................................................................................8 UNO-S2 Keypad ...........................................................
TABLE OF CONTENTS Making Connections UNO Keypad Port Connections...........................................................................................36 Source Audio Input Connections .........................................................................................37 Source IR Input Connections ..............................................................................................37 Common IR Input Connection ..............................................................................
USER SECTION Component Guides Explains front panel features of the CAM6.6 controller, UNO-S1 keypad, UNO-S2 keypad and UNO-LRC1 remote control. Operation Step-by-step outline of the system's normal operation, plus a look at adjustable features available through the User Menu.
PRODUCT INTRODUCTION Thank you for choosing the Russound® CAM6.6X-S1/S2 System to enhance your home with distributed audio. It combines the CAM6.6 Controller Amplifier and UNO keypads into a state-of-the-art home audio system that blends seamlessly with your unique lifestyle and preferences. Besides distributing and controlling six audio sources to six rooms (zones), your CAM6.6X-S1/S2 System offers many features that increase your enjoyment of living.
USER COMPONENT GUIDE CAM6.6 Controller-Front Panel 1 2 1 MAIN POWER SWITCH - Supplies power to the CAM6.6 2 ROOM LED ON/OFF INDICATORS - Indicates when a room is on (green) or off (red) Main Power and Zone Status The power switch for the CAM6.6 controller is "on" in the up position. Any active room is indicated on the front of the controller by a green LED, which shows red when the room is inactive.
USER COMPONENT GUIDE UNO-S1 Keypad-Front Panel 1 Blues 2 6 3 5 4 1 LCD PANEL - 5-character backlit display shows status of the room, source, volume, and more 2 SOURCE SELECT BUTTON - Scrolls through the sources directly connected to the CAM6.6. Press and hold brings up the USER MENU for loudness, bass, treble, etc. 3 VOLUME UP/DOWN BUTTONS - Raises and lowers the volume for the room 4 IR RECEIVER - Receives IR signals and passes them to the controller and source equipment.
USER COMPONENT GUIDE UNO-S2 Keypad-Front Panel 1 7 CD PLAYER 1 2 6 3 5 4 1 LCD PANEL - 12-character backlit display shows status of the room, source, volume, and more 2 SOURCE SELECT BUTTON - Scrolls through the sources directly connected to the CAM6.6. Press and hold brings up the USER MENU for loudness, bass, treble, etc. 3 VOLUME UP/DOWN BUTTONS - Raises and lowers the volume for the room 4 IR RECEIVER - Receives IR signals and passes them to the controller and source equipment.
USER COMPONENT GUIDE UNO-LRC1 Remote Control 2 3 4 1 LOCAL DEVICE BUTTONS - Select local source to be controlled by UNO-LRC1. 2 SETUP - Use for programming UNO-LRC1 using the built-in library or by learning-in codes. 3 UNO SOURCE BUTTON - Selects UNO Keypad for control by UNO-LRC1. 4 ROOM ON/OFF - Turns room on and off while in the UNO mode. 5 NUMBER BUTTONS - Buttons (0-9) for direct selection of channels or tracks. 6 INPUT - Scrolls through sources connected to the CAM6.
USER OPERATION UNO-S1 Keypad Zone On/Off Press and release to turn on the UNO System Keypad. This also turns on the corresponding CAM6.6’s room, and any presets previously assigned will be activated, including settings for bass, volume, last source selected, etc. Press and release to turn off the UNO System Keypad. This will also put the corresponding CAM6.6’s room into a standby state. User Menu with a press and hold action.
USER USER MENU SETTINGS UNO-S1 User Menu Operation The User Menu allows the user to adjust the audio properties and control functions of a particular room. To enter or exit the User Menu, press and hold during normal operation. The following keys are used to navigate and make changes while using the User Menu: Press and hold to adjust feature setting (increment) Press and hold to adjust feature setting (decrement) Go to next feature. Go to previous feature. View current feature setting.
USER OPERATION UNO-S2 Keypad Zone On/Off Press and release is also used to enter the User Menu with a to turn on the UNO System Keypad. This also turns on the corre- press and hold action. (See next page for User sponding CAM6.6’s room, and any presets previ- Menu) ously assigned will be activated, including settings for bass, volume, last source selected, etc. Press and release Volume Up/Down Buttons The room’s audio output is adjusted using . to turn off the UNO System Keypad.
USER USER MENU SETTINGS UNO-S2 User Menu Operation The User Menu allows the user to adjust the audio properties and control functions of a particular room. The following keys are used to navigate and make changes while using the User Menu: To enter the User Menu, press and hold during normal operation. To exit the User Menu, press and release . Adjust feature setting (decrement). Go to next feature. Go to previous feature. View current feature setting.
USER INTERNAL SOURCE - XM TUNER XM Radio Overview XM Radio Activation XM Radio is over 100 channels of radio broadcasts with the signal delivered by satellite and (depending on location) transferred by terrestrial antennas. The radio is a subscription-based service with a monthly provider fee and an activation charge. XM radio broadcasts several channels for preview but will not broadcast the full range of channels without activation. Activation and billing are handled solely through XM Radio.
USER INTERNAL SOURCE - XM TUNER XM Radio Modes XM Radio Modes There are four user “modes” for selecting music on the XM Tuner: Preset (default or normal) Category Search Now Playing Display Preferences. These modes are accessed through certain button and key presses from the tuner panel, remote controls and keypads. When choosing modes, if no choice is made after 20 seconds, the tuner will time out by showing EXIT and return to tuner display and Preset mode.
USER INTERNAL SOURCE - XM TUNER XM Radio Modes Preset (default) Mode This is the normal operating mode of the XM tuner for channel up and down, bank selection and memory presets. Next Preset This button press accesses the next saved preset (6 presets for each bank) in the chosen bank. Previous Preset This button press accesses the previous saved preset in the chosen bank Next Bank This button press accesses the next bank (total of 6 banks). Previous Bank This button press accesses the previous bank.
USER INTERNAL SOURCE - XM TUNER XM Radio Modes 1.CAT SEARCH) Category Search Mode (1 XM Radio is organized by Channel Category (e.g., Rock, Country, News). Within each category is a series of channels (e.g., Top Tracks, Bluegrass Junction, XM Classics). Channel selection in this mode is refined to scrolling only those channels in the selected category. Next Category This button press accesses the next category from the current category.
USER INTERNAL SOURCE - XM TUNER XM Radio Modes 2.NOW PLAYNG) Now Playing Mode (2 This mode displays information about the current XM selection. Appropriate button presses access the next or previous information item. NAME: Displays the artist’s name, feature name or program name (news, talk, sports). TITLE : Displays the song title or program title. CATEGORY : Displays the current category. UNO-S1 UNO-S2 UNO-LRC1 Now Playing Mode Next Info Item Previous Info Item 3.
USER INTERNAL SOURCE - XM TUNER UNO-S1 Keypad Control UNO-S1 Keypad Control of Tuner channel selection. Once active, press Selecting the tuner to scroll through channels. The channel will On the UNO-S2 keypad, press to select the XM Tuner by choosing the tuner’s preassigned source number (1). Selecting the desired channel Press and hold and to activate manual scroll twice on the keypad then stop and display the channel display format’s first five characters.
USER INTERNAL SOURCE - XM TUNER UNO-S2 Keypad Control UNO-S2 Keypad Control of Tuner Selecting the tuner On the UNO-S2 keypad, press then release. The display shows the signal to select the XM Tuner by choosing the tuner’s preassigned source number (1). strength rating. To exit, press again. Selecting a Bank To select a bank, press and hold for bank Selecting a Mode up or Push be temporarily displayed on the UNO-S2. to toggle between XM modes. for bank down.
USER INTERNAL SOURCE - XM TUNER UNO-S2 Keypad Control 1 6 XM Classics 5 2 4 3 1 TUNER SELECTION - Select source number assigned to XM TUNER (1) 2 TUNE UP/DOWN - Used for manual channel selection 22 3 SELECT - XM operating mode toggle 4 SEEK - (press) Exit current XM mode 4 SCAN - (press and hold) XM Signal Strength mode toggle 5 MUTE - Mutes/unmutes tuner audio output 6 BANK SELECT - Used for bank selection (press and hold) 6 MEM UP/DOWN - Scrolls through memory preset stations (press)
USER INTERNAL SOURCE - XM TUNER UNO-LRC1 Remote Control UNO-LRC1 Remote Control of Tuner Selecting a Bank Selecting the tuner To select a bank, press and hold To select the XM tuner, push and choose the source number preassigned to the XM Tuner (1), or use the UNO numeric source inputs at the bottom of the UNO-LRC1. , for bank down.
USER INTERNAL SOURCE - XM TUNER UNO-LRC1 Remote Control UNO SELECTION - UNO must be the selected source for control of the CAM6.6 and any connected components. Select UNO before sending UNO-LRC1 remote commands. 1 POWER - Power managed by CAM6.6 2 NUMERIC INPUT - Number buttons for direct input of channel, preset, bank (press).
INSTALLER SECTION Getting Started Includes an installation overview, including tools needed and wiring instructions. Component Guides Reviews front and back panel features of the CAM6.6 controller and the UNO-S1 and UNO-S2 keypads. Keypad Installation Explains UNO-S1 and UNO-S2 keypad installation and wiring. Making Connections Details front and back panel connections of the controller and the keypad.
INSTALLER GETTING STARTED Unpacking the System Components • Keep the original carton and packing materials for future shipment or storage. • Check for any visible signs of damage. If you encounter any concealed damage, consult your Russound dealer before proceeding to install the unit. • Retain the sales receipt as it establishes the duration of the limited warranty and provides information for insurance purposes. CAM6.6X-S1/S2 System Components: • 1 (one) CAM6.
INSTALLER WIRING INSTRUCTIONS CAUTION Do not connect the controller's main power feed until all other connections have been made and verified. Live connection or removal of the keypad wiring or other wiring when the system is powered can cause communication problems in the network. Double-check terminations during each phase of the installation to prevent accidental damage. Incorrect wiring is the number one cause for non-warranty product damage.
INSTALLER COMPONENT GUIDE CAM6.6 Controller-Rear Panel 1 2 3 4 5 6 7 8 9 10 ANTENNA 19 20 28 18 17 16 15 14 11 CAM6.6 13 12 1 RNET LINK IN AND LINK OUT - Links multiple CAM6.6’s, also links future Russound components that are RNET compatible 2 RS-232 INTERFACE - The RS-232 Interface allows the zones to be controlled by PC or other devices that have an RS-232 Interface. The RS-232 Interface also allows for firmware updates and programming.
INSTALLER COMPONENT GUIDE CAM6.6 Controller-Rear Panel 10 OPTIONAL INTERNAL SOURCE - Factory installed optional internal source, XM radio module 11 AC 240V-AC 110V Switch - Switches A/C input voltage between 110VAC and 240VAC 12 AC 120/240 INPUT - Grounded 3-terminal plug detachable power cord connection for the CAM6.6 13 FUSE HOLDER - Holds a replaceable fuse for A/C input connection 110VAC operation-F 3A H 250V, 240VAC operation-F 1.
INSTALLER COMPONENT GUIDE UNO-S1 Keypad-Update Port 1 3 2 Data Rx TTL Level Data Tx TTL Level GND +12VDC Note: Do not put RS-232-level signals into the pins. Must use Advanced Programming Cable P/N 2500-521065. 30 1 OS Update/Run Jumper -The pins are jumpered when performing an OS update on the keypad, and removed during normal operation. (Typically needed only on a keypad that has never been updated) 2 Setup Button - Activates information and update menus for the keypad.
INSTALLER COMPONENT GUIDE UNO-S1 Keypad-CAT-5 Connection NEWMARKET, NH U.S.A. 1 GR GND +12V BR/W +12V BR OR GND STATUS IN GR/W COM B BL/W 1 COM A BL IR OUT OR/W DESIGNED IN USA MADE IN KOREA UNO-S1 System Control Keypad 110 PUNCHDOWN CONNECTOR - Termination for CAT-5 connection between the UNO-S1 Keypad and the CAM6.6 controller. CAT-5 Connection Caution: The UNO-S1 Keypad uses a 110-punchdown terminal to provide a simple installation and strong connection for CAT-5 cable’s eight conductors.
INSTALLER COMPONENT GUIDE UNO-S2 Keypad-Update Port 1 DATA Rx (RS-232) DATA Tx (RS-232) GND N/C +12VDC 2 32 1 SETUP BUTTON - Activates Installer Setup Mode for the UNO-S2 keypad 2 OS UPDATE PORT - The OS Update Port is used to update the UNO-S2 Keypad operating system software in the future. If an update is released, it will be available online through the Document Center on www.russound.com. Look for it in the “Firmware and Downloads” section under Multi-Zone product type.
INSTALLER COMPONENT GUIDE UNO-S2 Keypad-CAT-5 Connection 2 3 1 KOREA 4 1 EXTERNAL IR RECEIVER IN CONNECTOR - Connection for an external IR Receiver. 2 OS UPDATE JUMPER - Selects “Run” or “OS Update” mode. 3 RESET BUTTON - Reset whenever changing from RUN to OS update 4 110 PUNCHDOWN CONNECTOR - Termination for CAT-5 connection between the UNO-S2 Keypad and the CAM6.6 controller.
INSTALLER UNO-S1 KEYPAD-INSTALLATION Keypad Location The best infrared remote performance is achieved with the keypad away from any direct sunlight, plasma TV, and low voltage lighting controls. Also consider convenience when choosing a location. Choose a place that is easily seen from the position where a person is most likely to be located. Check whether or not you can route the wire to the location you have chosen.
INSTALLER UNO-S2 KEYPAD-INSTALLATION Keypad Location Keypad Installation To install a double-gang keypad, you will need to use a UL/CSA approved plastic double-gang electrical box. Route CAT-5 wire to the junction box from the CAM6.6. Ensure jumper settings on keypads are in the run positions. Mount the keypad in the electrical box and attach the cover plate. Repeat the steps until all keypads are installed.
INSTALLER MAKING CONNECTIONS UNO Keypad Port Connection The UNO System Keypad Ports are located on the back of the CAM6.6 in the top left of center. Connections made at the UNO Keypad Ports are made using CAT-5 T568A RJ-45 wire configuration. CAT-5 is color-coded for ease of installation. For a clean installation when wiring from an UNO System Keypad Port use an RJ-45 CAT-5 patch cable to connect from the keypad port to an RJ-45 Wall Plate (optional).
INSTALLER MAKING CONNECTIONS Source Audio and IR Input Connections Source Audio Connections The CAM6.6 supports up to six audio sources. The Source Inputs are located at the back panel. The Source 1 input serves a dual purpose. If the CAM6.6 optional internal source is used, the Source 1 inputs are not available, and the switch next to it is set to “Internal Source Output.
INSTALLER MAKING CONNECTIONS Common IR Connection Common IR Connections The Common IR jack on the rear of the CAM6.6 allows control of any source equipment without that source being selected on the keypad. The connection for the COM IR jack is made using an IR emitter with a 1/8’’ plug. The Russound 845.1 single IR emitter is recommended, or use an IR connecting block such as the Russound 857 which allows multiple units to be controlled through the COM IR Port.
INSTALLER MAKING CONNECTIONS Speaker Connections The speakers are connected to the CAM6.6 using modular snap connectors. Each of these color-coded connectors is designated for the speaker set of a particular amplified zone. To avoid confusion, connect one zone speaker set at a time starting with Zone 1, taking care to keep zone and speaker wire identities straight. Note: An 8 Ohm minimum speaker is required for each amplified output.
INSTALLER MAKING CONNECTIONS Zone Fixed/Variable Audio Outputs The CAM6.6 has two Zone Audio outputs, on Zone 1 and Zone 2. Each of these zone audio output connections features a stereo line out RCA connection plus a switch to allow for either a fixed or a variable line level output. When set to Variable, the keypad volume level affects this output. In the Fixed position, keypad volume level will not change the output level.
INSTALLER MAKING CONNECTIONS 12VDC Home Theater Trigger In/Out 12VDC Home Theater Trigger In This 12VDC Trigger input is used to control Power Management of the audio sources possibly being shared with a home theater system. When the last zone on the CAM6.6 is turned off, 12VDC presence to the trigger input will prevent the sources that are on from being turned off. The connections for the trigger are made using a twoconductor cable with 1/8” male mini-plug.
INSTALLER MAKING CONNECTIONS 12VDC Mute Trigger In/Out 12VDC Mute Trigger In When 12VDC is applied to the Mute Trigger In, the system will fully mute any source connected to the Source Audio Input. The connections for the trigger are made using a two-conductor cable with 1/8” male mini-plug jacks. The tip is positive (+) and sleeve is negative (-). This allows for the connection of an external or muting device. The CAM6.
INSTALLER MAKING CONNECTIONS RNET Link In and Link Out The RNET Link In and Link Out is used to connect two or more CAM6.6 or CAV6.6 controllers. The connection is made using a CAT-5 patch cable from the Link Out of the master CAM6.6 and into the Link In of the next controller. Along with RNET data signals, the RNET Link In and Link Out jack passes the six source IR signals. These are only for source-specific IR remote repeating, not codes initiated from the controller’s internal IR library.
INSTALLER MAKING CONNECTIONS RS-232 Interface The CAM6.6 supports RS-232 communication with various third party automation systems or PC for programming of the controller. The RS232 com port is located on the back of the CAM6.6 and uses a DB-9 cable connection. For RS-232 protocol and the backup PC application, see the Document Center at www.russound.com. Look for the Technical Documents under Multi-source/Multi-room products. ANTENNA INTERFACE DB-9 Cable 44 CAM6.
INSTALLER MAKING CONNECTIONS Optional Internal Source - XM Tuner Antennas XM Antenna XM Signal Strength Mode Connect the included XM antenna for XM reception to the back panel of the XM module. The antenna comes with 20 feet of cable. If this length is not sufficient, there are aftermarket antenna kits available for custom lengths. Position the antenna near a south-facing window to receive the best signal from a satellite or terrestrial signal. To test the XM reception, turn the unit on.
INSTALLER INITIAL INSTALL TEST Before proceeding to the system programming section, it’s important to conduct an initial test to determine that the hardware components are working properly. 1. Connect the speaker wires from Zone #3 to the CAM6.6 Zone #3 speaker output connectors. 2. Connect an UNO-S1 or UNO-S2 keypad to Keypad Port #3 on the rear of the CAM6.6. 3. Connect a source to the Source #3 Input on the CAM6.6 using RCA Audio patch cables. 4. Plug a supplied 845.
INSTALLER SYSTEM PROGRAMMING OVERVIEW This manual includes items that are designed to assist in the programming process. Forms (Pages 49-51) Three blank reproducible forms are included as planning tools when determining sources, settings and zone preferences. The Source and Zone Information forms and the Macro Editor form should be completed before programming, and referred to during the Installation Menu process. This speeds up programming time and reduces missed or incorrect entries.
INSTALLER SYSTEM PROGRAMMING OVERVIEW 3. Basic Setup (SOURCE SETUP) (Pages 55-56) This procedure is mandatory to set up each source for keypad source control and is the cornerstone of the programming process. 4. Peripheral Setup (Pages 53-55) (FOR OPTIONAL INTERNAL SOURCE) This procedure provides setup and naming procedures for the XM tuner. It includes assigning a custom name to a memory preset or bank. 5.
N/A N/A N N/A N N/A Peripheral N/A Russound INSTALLER SETUP FORMS 49
INSTALLER Mute SETUP FORMS 50
INSTALLER SETUP FORMS 51
INSTALLER INSTALLATION MENU OVERVIEW There are three item types in the installation menu: Menu Item (m) – Acts as a folder that holds procedures and/or feature parameters. Procedure (p) – A sequence of feature parameters to perform a guided operation, such as configuring an UNO key. Once you begin a procedure, the system will prompt for the needed information to complete the task. Feature (f) – The actual parameters (settings) that will change the system configuration.
INSTALLER INSTALLATION MENU The following items make up the Installation Menu: PERIPH SETUP (PerSu) CTRLR SETUP (CtlSu) SOURCE SETUP (SrcSu) POWER MGT (PwMgt) MACRO EDITOR (MacEd) ZONE SETUP (ZonSu) LEARN IR (LrnIR) SYSTEM INFO (SInfo) PERIPH SETUP (PerSu) Peripheral Setup allows the CAM6.6’s optional internal source to be configured.
INSTALLER INSTALLATION MENU 2. BANK NAME – (BnkNm) Use the up/down keys to select a character and left/right keys to change a character position. A blinking cursor indicates the placement of the character being entered. Names can be from 1 to 12 characters in length. CONTROLLR ID (CtlId) This procedure is used to identify the controller(s) that the tuner will respond to. See Periph Setup - Flow Chart page 68 1. Controller:# – (CtlId) Select controller ID of controller that will control tuner. 2.
INSTALLER INSTALLATION MENU 1. BUILD TIME (BTime) Displays the firmware Build Time of the tuner. 2. BUILD DATE (BDate) Displays the firmware Build Date of the tuner. 3. VERSION (Ver) Displays the firmware version of the tuner. SOURCE SETUP (SrcSu) Source Setup allows the system’s sources to be configured.
INSTALLER INSTALLATION MENU 56 a. Selected: Learned IR (LrnIR) Choose Learned IR if the pre-programmed IR code library does not support the source component. i. LEARNED SRC – (LnSrc) Select the learned source bank to be assigned to the source component. (See Learning IR procedure for instructions on how to learn IR codes.) ii. TEMPLATE TYP – (TType) Select the template type to define what type of source component is being used. (This will tell the CAM6.
INSTALLER INSTALLATION MENU KEY CONFIG (KeyCf) Key Configuration defines zone-specific key functions for each source. See Key Config. - Flow Chart page 70 1. ZONE NUM – (Zone#) Select the zone the key will be configured for. Changes are made for that zone only; default setting is “All Zones.” 2. SOURCE NUM – (Src #) Select the source the key will be configured for. 3. SELECT A KEY – (SelKy) Using 4. KEY TYPE – (KeyTp) Either “Key Press,” “Key Hold” or “Both” will activate the command. 5.
INSTALLER INSTALLATION MENU 9. SAVE CHANGES? – (Save?) Select “yes” to save changes. Procedure advances to ZONE NUM (step 1) SOURCE NAMES (SrcNm) This procedure allows the installer to customize the source names for the sources attached to the CAM6.6. See Source Names/Vol Trim - Flow Chart page 71 1. SOURCE NUM – (Src #) Select the source number this name will be assigned to. 2. SOURCE NAME – (Name) Select the name.
INSTALLER INSTALLATION MENU 4. NUMERIC TEXT – (NmTxt) Select Numeric descriptive text. 5. PREFIX CMD – (Prefx) Tells the system whether a command will be issued prior to the selection of the numerical value (e.g., Disc 1,2). If “no,” procedure advances to SUFFIX CMD (step 9) 6. COMMAND TYPE – (CmdTp) Select the type of command (e.g., CD, TV, etc.). a. Selected: Learned IR (LrnIR) i. LEARNED SRC – (LnSrc) Choose Learned IR if the pre-programmed IR code library does not support the source component.
INSTALLER INSTALLATION MENU i. LEARNED SRC – (LnSrc) Select the learned source bank to be assigned to the source component. Procedure advances to KEY FUNCTION (step 12) b. Selected: Unassigned (Unasg) The numeric IR Suffix command is cleared. Procedure advances to SOURCE NUM (step 1) c. Selected: Default (Deflt) Default selects the same device type and device code previously setup in BASIC SETUP. Procedure advances to KEY FUNCTION (step 12) d. Selected: Macro: i.
INSTALLER INSTALLATION MENU c. Selected: Default (Deflt) Default selects the same device type and device code previously setup in BASIC SETUP. Procedure advances to KEY FUNCTION (step 4) d. Selected: Macro: i. MACRO (Macro) (To build macros, see Macro Editor page 65) Macro loads a series of commands which are processed when activated. ii. MACRO ID – (MacID) Enter the macro ID number. Menu advances to SAVE CHANGES (step 5) e. All Other Selections: Procedure advances to DEVICE CODE (step 3) 3.
INSTALLER INSTALLATION MENU disabled zone. If enabled, an All On command activated from another zone will turn on the enabled zone. 3. PARTY ENABLE (PtyEn) This feature is either disabled or enabled. If disabled, Party Mode activation from another zone will not affect the disabled zone. If enabled (default), the zone will participate with Party Mode. 4. MASTER ENABLE (MstEn) This feature is either disabled or enabled. If disabled, the zone cannot host a master keypad during Party Mode.
INSTALLER INSTALLATION MENU All sources that have power management enabled are initialized by a “POWER ON” command/ macro. Power management is initialized when the first keypad is turned on or when the home theater trigger input has 12VDC present. The 12VDC trigger output is turned on when the first zone is turned on. All sources that have power management enabled are turned off by the “POWER OFF” command after all zones have been turned off, with a timeout of five minutes.
INSTALLER INSTALLATION MENU 6. POWER OFF CMD – (OfCmd) Tells the controller to turn off the selected source equipment (by SOURCE NUMBER) when the last of the UNO System Keypads is turned off. If “no,” procedure advances to SAVE CHANGES (step 10) 7. COMMAND TYPE – (CmdTp) Select the type of source command (e.g., CD, TV, etc.). a. Selected: Learned IR (LrnIR) Choose Learned IR if the pre-programmed IR code library does not support the source component. i.
INSTALLER INSTALLATION MENU 2. KEY FUNCTION – (KeyFn) Select the function to be learned or deleted. 3. LEARN/DELETE – (Ln/Dl) Select Learn IR Now or Delete IR. If Learn IR Now, a “USE REMOTE” prompt appears. Point the learning remote at the controller’s IR window. If Delete IR, procedure returns to LEARNED SRC (step 1) 4. TEST IR? – (TstIR) If “yes,” sends the learned command to the source component to test the IR. If the component responds, the IR test was a success.
INSTALLER INSTALLATION MENU b. Selected: Unassigned (Unasg) Selected command and subsequent commands are cleared. Procedure advances to COMMAND NUM (step 3) c. Selected: Default (Deflt) Default selects the same device type and device code previously setup in BASIC SETUP. Procedure advances to KEY FUNCTION (step 6) d. Selected: Macro: i. MACRO (Macro) A macro can “call” another macro if a sequence of more than 10 commands is needed. ii. MACRO ID – (MacID) Enter the macro ID number.
BANK # MEM NAME Procedure PERIPH SETUP Menu MEMORY # SAVE CHANGES? Repeat for each character in name Selects character position Selects character MEMORY NAME BANK # BANK NAME Procedure Repeat for each character in name Selects character position Selects character BANK NAME CONTROLLR ID Procedure SAVE CHANGES? Procedure DIAGNOSTICS FACTORY INIT Procedure Peripheral Setup: Memory Name, Bank Name SYSTEM INFO Procedure Peripheral Menu INSTALLER SETUP MENU FLOW CHARTS 67
MEM NAME Procedure PERIPH SETUP Menu BANK NAME Procedure All Contrlrs Controller:# CONTROLLR ID Procedure This Procedure is for Factory use ONLY Procedure DIAGNOSTICS NO Cycle Power Please wait YES Are you sure This Procedure returns the Tuner to its Factory settings FACTORY INIT Procedure SYSTEM INFO Procedure Peripheral Menu Peripheral Setup: Controller ID, Diagnostics, Factory Init, System Info INSTALLER SETUP MENU FLOW CHARTS
INSTALLER PERIPH SETUP Menu Peripheral SETUP MENU FLOW CHARTS 69
INSTALLER PERIPH SETUP Menu SETUP MENU FLOW CHARTS 70
INSTALLER PERIPH SETUP Menu SETUP MENU FLOW CHARTS 71
INSTALLER PERIPH SETUP Menu SETUP MENU FLOW CHARTS 72
INSTALLER PERIPH SETUP Menu SETUP MENU FLOW CHARTS 73
INSTALLER PERIPH SETUP Menu MUTE SETUP MENU FLOW CHARTS 74
INSTALLER PERIPH SETUP Menu SETUP MENU FLOW CHARTS 75
INSTALLER PERIPH SETUP Menu SETUP MENU FLOW CHARTS 76
PERIPH SETUP Menu LED on rear CAM Panel blinks fast INSTALLER SETUP MENU FLOW CHARTS 77
INSTALLER PERIPH SETUP Menu SETUP MENU FLOW CHARTS 78
INSTALLER PERIPH SETUP Menu SETUP MENU FLOW CHARTS 79
INSTALLER IR CODES Device Codes for TVs: AOC Admiral Advent Aiko Aiwa Akai Alaron America Action Ampro Anam Apex Digital Audiovox Baysonic Belcor Bell & Howell Bradford Brockwood Broksonic CXC Candle Carnivale Carver Celebrity Changhong Cineral Citizen Concerto Contec Craig Crosley Crown Curtis Mathes Daewoo Daytron Denon Dumont Dwin Electroband Emerson Envision Fisher Fujitsu Funai Futuretech GE Gibralter GoldStar Gradiente Grunpy Hallmark Harley Davidson Harman/Kardon Harvard Havermy Hitachi Infinity In
INSTALLER IR CODES Philips Pioneer Princeton Samsung Sensory Science Sharp Sony 1818, 1061 1010 0113, 0295 1190, 1204 1126 1010 0850 Device Codes for SAT/DSS: AlphaStar Chaparral Crossdigital Echostar Expressvu GE GOI General Instrument HTS Hitachi Hughes Net. Sys.
INSTALLER IR CODES Realistic Sony Technics 0203 0201, 0193 0204 Device Codes for DVD Players: Aiwa Apex Digital Blue Parade Broksonic Daewoo Denon Emerson Enterprise Fisher GE Go Video Gradiente Harman/Kardon Hitachi Hiteker JBL JVC Kenwood Konka Koss Lasonic Magnavox Malata Marantz Microsoft Mitsubishi Onkyo Oritron Panasonic Philips Pioneer Princeton Proscan RCA Rowa Sampo Samsung Sansui Sanyo Sharp Sherwood Sony Sylvania Technics Techwood Theta Digital Toshiba Urban Concepts Yamaha Zenith 0641 0672,
INSTALLER KEY CODES TV (HDTV) KEY FUNCTION UNO-S1 TV (HDTV) KEY FUNCTION UNO-S1 TV (HDTV) 1 1 Digit 1 Pause Pause Learned Only 2 2 Digit 2 Record Recrd Learned Only 3 3 Digit 3 Menu Menu Menu (Picture) 4 4 Digit 4 Menu Up MenuU Menu Up, Adjust Up 5 5 Digit 5 Menu Dn MenuD Menu Dn, Adjust Dn 6 6 Digit 6 Menu Left MenuL Menu Left 7 7 Digit 7 Menu Right MenuR Menu Right 8 8 Digit 8 Select Sel Menu Select 9 9 Digit 9 Exit Exit Exit, Cancel 0 0 Digit 0
INSTALLER KEY CODES TV (HDTV) 84 KEY FUNCTION UNO-S1 TV (HDTV) KEY FUNCTION UNO-S1 TV (HDTV) Off Off Off, Power On/Off PIP Chan Up PIPCU PIP Channel Up 11 11 Learned Only PIP Chan Dn PIPCD PIP Channel Down 12 12 Learned Only Input 1 In 1 VID1,Video,TVp1 13 13 Learned Only Input 2 In 2 VID2,TVp2 14 14 Learned Only Input 3 In 3 VID3,TVp3 15 15 Learned Only Input 4 In 4 VID4,TVp4 16 16 Learned Only Input 5 In 5 VID5,AV1,VCR,BNC Bright Brght Learned Only Input 6
INSTALLER KEY CODES CABLE KEY FUNCTION UNO-S1 CABLE KEY FUNCTION UNO-S1 CABLE 1 1 Digit 1 Pause Pause Pause 2 2 Digit 2 Record Recrd Record 3 3 Digit 3 Menu Menu Menu, Settings 4 4 Digit 4 Menu Up MenuU Menu Up 5 5 Digit 5 Menu Dn MenuD Menu Down 6 6 Digit 6 Menu Left MenuL Menu Left 7 7 Digit 7 Menu Right MenuR Menu Right 8 8 Digit 8 Select Sel Menu Select 9 9 Digit 9 Exit Exit Exit, Cancel 0 0 Digit 0 Display Displ Info, Display, OSD Volume Up
INSTALLER KEY CODES CABLE 86 KEY FUNCTION UNO-S1 CABLE KEY FUNCTION UNO-S1 CABLE Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 A,VID1,Video,TVp1 13 13 Learned Only Input 2 In 2 B,VID2,TVp2 14 14 Learned Only Input 3 In 3 C,VID3,TVp3 15 15 Learned Only Input 4 In 4 VID4,TVp4 16 16 Learned Only Input 5 In 5 VID5,AV1,VCR,BNC Bright Brght Learned Only Input 6 In 6 VID6,
INSTALLER KEY CODES VIDEO ACC KEY FUNCTION UNO-S1 VIDEO ACC KEY FUNCTION UNO-S1 VIDEO ACC 1 1 Digit 1 Pause Pause Pause 2 2 Digit 2 Record Recrd Record 3 3 Digit 3 Menu Menu Menu, Home 4 4 Digit 4 Menu Up MenuU Menu Up 5 5 Digit 5 Menu Dn MenuD Menu Dn 6 6 Digit 6 Menu Left MenuL Menu Left 7 7 Digit 7 Menu Right MenuR Menu right 8 8 Digit 8 Select Sel Menu Select 9 9 Digit 9 Exit Exit Exit, Cancel, Go 0 0 Digit 0 Display Displ Info, Display, OSD
INSTALLER KEY CODES VIDEO ACC 88 KEY FUNCTION UNO-S1 VIDEO ACC KEY FUNCTION UNO-S1 VIDEO ACC Off Off Off, Power On/Off PIP Chan Up PIPCU PIP Channel Up 11 11 Learned Only PIP Chan Dn PIPCD PIP Channel Down 12 12 Learned Only Input 1 In 1 VID1,Video,TVp1 13 13 Learned Only Input 2 In 2 VID2,TVp2 14 14 Learned Only Input 3 In 3 VID3,TVp3 15 15 Learned Only Input 4 In 4 VID4,TVp4 16 16 Learned Only Input 5 In 5 VID5,AV1,VCR,BNC Bright Brght Learned Only Input 6
INSTALLER KEY CODES SAT/DSS KEY FUNCTION UNO-S1 SAT/DSS KEY FUNCTION UNO-S1 SAT/DSS 1 1 Digit 1 Pause Pause Pause 2 2 Digit 2 Record Recrd Record 3 3 Digit 3 Menu Menu Menu (PVR, Tivo) 4 4 Digit 4 Menu Up MenuU Menu Up 5 5 Digit 5 Menu Dn MenuD Menu Down 6 6 Digit 6 Menu Left MenuL Menu Left 7 7 Digit 7 Menu Right MenuR Menu Right 8 8 Digit 8 Select Sel Menu Select 9 9 Digit 9 Exit Exit Exit, Cancel 0 0 Digit 0 Display Displ Info, Display, OSD
INSTALLER KEY CODES SAT/DSS 90 KEY FUNCTION UNO-S1 SAT/DSS KEY FUNCTION UNO-S1 SAT/DSS Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 VID1,Video,TVp1 13 13 Learned Only Input 2 In 2 VID2,TVp2 14 14 Learned Only Input 3 In 3 VID3,TVp3 15 15 Learned Only Input 4 In 4 VID4,TVp4 16 16 Learned Only Input 5 In 5 VID5,AV1,VCR,BNC Bright Brght Learned Only Input 6 In 6 VID6,
INSTALLER KEY CODES VCR KEY FUNCTION UNO-S1 VCR KEY FUNCTION UNO-S1 VCR 1 1 Digit 1 Pause Pause Pause 2 2 Digit 2 Record Recrd Record 3 3 Digit 3 Menu Menu Menu (PVR,Tivo) 4 4 Digit 4 Menu Up MenuU Menu Up 5 5 Digit 5 Menu Dn MenuD Menu Down 6 6 Digit 6 Menu Left MenuL Menu Left 7 7 Digit 7 Menu Right MenuR Menu Right 8 8 Digit 8 Select Sel Menu Select 9 9 Digit 9 Exit Exit Exit, Cancel 0 0 Digit 0 Display Displ Display, OSD, Info Volume Up Vol
INSTALLER KEY CODES VCR 92 KEY FUNCTION UNO-S1 VCR KEY FUNCTION UNO-S1 VCR Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 VID1,Video,TVp1 13 13 Learned Only Input 2 In 2 VID2,TVp2 14 14 Learned Only Input 3 In 3 VID3,TVp3 15 15 Learned Only Input 4 In 4 VID4,TVp4 16 16 Learned Only Input 5 In 5 VID5,AV1,VCR,BNC Bright Brght Learned Only Input 6 In 6 VID6,AV2,VDP,DVD,
INSTALLER KEY CODES LASER DISC KEY FUNCTION UNO-S1 LASER DISC KEY FUNCTION UNO-S1 LASER DISC 1 1 Digit 1 Pause Pause Pause 2 2 Digit 2 Record Recrd Learned Only 3 3 Digit 3 Menu Menu Menu, Program 4 4 Digit 4 Menu Up MenuU Menu Up 5 5 5Digit 5 Menu Dn MenuD Menu Down 6 6 6Digit 6 Menu Left MenuL 7 7 Digit 7 Menu Right MenuR Menu Right 8 8 Digit 8 Select Sel Menu Select 9 9 Digit 9 Exit Exit Exit, Cancel 0 0 Digit 0 Display Displ Display, OSD, Info Vo
INSTALLER KEY CODES LASER DISC 94 KEY FUNCTION UNO-S1 LASER DISC KEY FUNCTION UNO-S1 LASER DISC Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 VID1,Video,TVp1 13 13 Learned Only Input 2 In 2 VID2,TVp2 14 14 Learned Only Input 3 In 3 VID3,TVp3 15 15 Learned Only Input 4 In 4 VID4,TVp4 16 16 Learned Only Input 5 In 5 VID5,AV1,VCR,BNC Bright Brght Learned Only Input 6 In
INSTALLER KEY CODES DVD KEY FUNCTION UNO-S1 DVD KEY FUNCTION UNO-S1 DVD 1 1 Digit 1, Traack 1 Pause Pause Pause 2 2 Digit 2, Track 2 Record Recrd Record 3 3 Digit 3, Track 3 Menu Menu Disk Menu 4 4 Digit 4, Track 4 Menu Up MenuU Menu Up 5 5 Digit 5, Track 5 Menu Dn MenuD Menu Dn 6 6 Digit 6, Track 6 Menu Left MenuL 7 7 Digit 7, Track 7 Menu Right MenuR Menu right 8 8 Digit 8,Track 8 Select Sel Menu Select 9 9 Digit 9, Track 9 Exit Exit Exit, Cancel, Return
INSTALLER KEY CODES DVD 96 KEY FUNCTION UNO-S1 DVD KEY FUNCTION UNO-S1 DVD Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 VID1,Video,TVp1 13 13 Learned Only Input 2 In 2 VID2,TVp2 14 14 Learned Only Input 3 In 3 VID3,TVp3 15 15 Learned Only Input 4 In 4 VID4,TVp4 16 16 Learned Only Input 5 In 5 VID5,AV1,VCR,BNC Bright Brght Learned Only Input 6 In 6 VID6,AV2,VDP,DVD,
INSTALLER KEY CODES RECEIVER KEY FUNCTION UNO-S1 RECEIVER KEY FUNCTION UNO-S1 RECEIVER 1 1 Digit 1 Pause Pause Pause 2 2 Digit 2 Record Recrd Record 3 3 Digit 3 Menu Menu Disk menu, Menu 4 4 Digit 4 Menu Up MenuU Menu Up, Adjust Up 5 5 Digit 5 Menu Dn MenuD Menu Dn, Adjust Dn 6 6 Digit 6 Menu Left MenuL Menu Left 7 7 Digit 7 Menu Right MenuR Menu Right 8 8 Digit 8 Select Sel MenuS elect, Continue 9 9 Digit 9 Exit Exit Exit, Cancel 0 0 Digit 0 Displa
INSTALLER KEY CODES RECEIVER 98 KEY FUNCTION UNO-S1 RECEIVER KEY FUNCTION UNO-S1 RECEIVER Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 CD 13 13 Learned Only Input 2 In 2 Tuner 14 14 Learned Only Input 3 In 3 DVD, LD 15 15 Learned Only Input 4 In 4 VCR, VID1 16 16 Learned Only Input 5 In 5 VID5,AV1,VCR,BNC Bright Brght Learned Only Input 6 In 6 TV, VID2 Dim Dim L
INSTALLER KEY CODES AMP/MISC AUDIO KEY FUNCTION UNO-S1 AMP/MISC AUDIO KEY FUNCTION UNO-S1 AMP/MISC AUDIO 1 1 Digit 1 Pause Pause Pause 2 2 Digit 2 Record Recrd Record 3 3 Digit 3 Menu Menu Menu, Program 4 4 Digit 4 Menu Up MenuU Menu Up, Adjust Up 5 5 Digit 5 Menu Dn MenuD Menu Dn, Adjust Dn 6 6 Digit 6 Menu Left MenuL Menu Left 7 7 Digit 7 Menu Right MenuR Menu Right 8 8 Digit 8 Select Sel Menu Select, Cont 9 9 Digit 9 Exit Exit Exit, Cancel 0 0 Digit
INSTALLER KEY CODES AMP/MISC AUDIO 100 KEY FUNCTION UNO-S1 AMP/MISC AUDIO KEY FUNCTION UNO-S1 AMP/MISC AUDIO Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 CD 13 13 Learned Only Input 2 In 2 Tuner 14 14 Learned Only Input 3 In 3 DVD, LD 15 15 Learned Only Input 4 In 4 TAPE, MD 16 16 Learned Only Input 5 In 5 VCR, VID1 Bright Brght Learned Only Input 6 In 6 TV, VID2
INSTALLER KEY CODES CD KEY FUNCTION UNO-S1 CD KEY FUNCTION UNO-S1 CD 1 1 Digit 1, Track 1,Dsc1 Pause Pause Pause 2 2 Digit 2, Track 2,Dsc2 Record Recrd Record 3 3 Digit 3, Track 3,Dsc3 Menu Menu Disk, Edit 4 4 Digit 4, Track 4,Dsc4 Menu Up MenuU Menu Up 5 5 Digit 5, Track 5,Dsc5 Menu Dn MenuD Menu Down 6 6 Digit 6, Track 6,Dsc6 Menu Left MenuL 7 7 Digit 7, Track 7,Dsc7 Menu Right MenuR Menu Right 8 8 Digit 8,Track 8,Dsc8 Select Sel Menu Select, Cont 9 9 Digit
INSTALLER KEY CODES CD 102 KEY FUNCTION UNO-S1 CD KEY FUNCTION UNO-S1 CD Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 CD 13 13 Learned Only Input 2 In 2 Tuner 14 14 Learned Only Input 3 In 3 DVD, LD 15 15 Learned Only Input 4 In 4 Tape, MD 16 16 Learned Only Input 5 In 5 VCR, VID1 Bright Brght Learned Only Input 6 In 6 TV, VID2 Dim Dim Learned Only Input 7 I
INSTALLER KEY CODES HOME CONTROL KEY FUNCTION UNO-S1 HOME CONTROL KEY FUNCTION UNO-S1 HOME CONTROL 1 1 Digit 1 Pause Pause Pause 2 2 Digit 2 Record Recrd Record 3 3 Digit 3 Menu Menu Menu 4 4 Digit 4 Menu Up MenuU Menu Up, Mode 5 5 Digit 5 Menu Dn MenuD Menu Dn, Timer 6 6 Digit 6 Menu Left MenuL Menu Left,Oscillate 7 7 Digit 7 Menu Right MenuR Menu Right,Speed 8 8 Digit 8 Select Sel Menu Select, Light 9 9 Digit 9 Exit Exit Exit, Cancel 0 0 Digit 0 D
INSTALLER KEY CODES HOME CONTROL 104 KEY FUNCTION UNO-S1 HOME CONTROL KEY FUNCTION UNO-S1 HOME CONTROL Off Off Off, Power On/Off PIP Chan Up PIPCU Learned Only 11 11 Learned Only PIP Chan Dn PIPCD Learned Only 12 12 Learned Only Input 1 In 1 Source/Scene 1 13 13 Learned Only Input 2 In 2 Source/Scene 2 14 14 Learned Only Input 3 In 3 Source/Scene 3 15 15 Learned Only Input 4 In 4 Source/Scene 4 16 16 Learned Only Input 5 In 5 Source/Scene 5 Bright Brght Learne
INSTALLER SOURCE NAMES UNO-S2 UNO-S1 UNO-S2 AUX CustomName3 DVD 3 DVD Player 3 Aux 1 AUX 1 CustomName4 FDoor Front Door Aux 2 AUX 2 CustomName5 Hers Her Music Blues Blues CustomName6 His His Music Cable Cable CustomName7 www.
INSTALLER SOURCE NAMES 106 UNO-S1 UNO-S2 UNO-S1 UNO-S2 RepTV Replay TV Tun 1 Tuner 1 Rock Rock Tun 2 Tuner 2 Sat Satellite Tun 3 Tuner 3 Sat 1 Satellite 1 TV TV Sat 2 Satellite 2 VCR VCR Sat 3 Satellite 3 VCR 1 VCR 1 SatRd Sat Radio VCR 2 VCR 2 Src 1 Source 1 <<>> Src 2 Source 2 XM 1 XM 1 Src 3 Source 3 XM 2 XM 2 Src 4 Source 4 XM 3 XM 3 Src 5 Source 5 XM XM Radio Src 6 Source 6 Src 7 Source 7 Src 8 Source 8 Spcl Special Tape Tape Tape
SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH ONE TUNER Sharing a single CAM6.6X (internal tuner) with multiple controllers Peripheral Setup Menu: Controller ID = All Controllers Output/Input Switch = Internal Source Output RCA cable connected to Source 1 This arrangement can support up to six CAM6.6 units for up to 36 zones/6 sources. Each additional CAM6.6 must have an incremental Controller ID # and RNET link. Audio from the source tuner can be split if used for all controllers. CAM6.
SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH TWO TUNERS System with two CAM6.6X (internal tuner) controllers The configuration below is suitable for 7-12 zones that will have access to the tuner in the controller to which its keypad is connected only. Built-in tuners are always Source 1 and cannot be changed. If you have more than one internal tuner, you must set each tuner to its specific Controller ID number.
SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH THREE TUNERS Sharing an ST2 Dual Tuner with multiple CAM6.6 controllers (with and without tuners) to Source 2 input on CAM6.6X (1) RCA cable connected from ST2 Tuner 2 audio output to Source 3 input on CAM6.6X (1) The configuration below is suitable for 7 to 12 zones that can access the ST2 Dual Tuner and the CAM6.6X tuner. This configuration uses RCA “Y” cables from the ST2 Tuner source outputs to connect to both CAM6.6 source inputs. CAM6.
SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH ST2 DUAL TUNER Sharing an ST2 Dual Tuner with multiple CAM6.6 controllers (no built-in tuners) to Source 1 input on CAM6.6 (1) RCA cable connected from ST2 Tuner 2 audio output to Source 2 input on CAM6.6 (1) This configuration is suitable for 7 to 12 zones that can all access the ST2 Dual Tuner. This configuration uses RCA “Y” cables from the ST2 Tuner source outputs to connect to both CAM6.6 source inputs. CAM6.
TECHNICAL SPECIFICATIONS Dimensions: Weight: Power Supply: Fuse Rating: 17"W x 12"D x 3.5"H (43 x 30.5 x 9 cm) 18 lbs. (8.1 kg) 110 or 240 VAC 110V input; F3A H 250V US and Canada 240V input; T1.25A H 250V Europe Frequency Response: Watts per channel: THD+N: Signal to Noise Ratio: Audio Source Inputs: Input Impedance: Audio Zone Outputs: 20Hz-20kHz +/- 1dB 20 Watts RMS into 8 Ohms <0.05% >88dB 6 (including internal tuner) 50 kohm 6 Speaker Level (8 ohms) (2 Line level) Max Source Audio Input: 2.
WARRANTY & REPAIR The Russound CAM6.6 is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. For this warranty to apply, the unit must be installed and used according to its written instructions. If service is necessary, it must be performed by Russound.
NOTES 113
NOTES 114
NOTES 115
Russound 5 Forbes Road, Newmarket, NH 03857 tel 603.659.5170 • fax 603.659.5388 e-mail: tech@russound.com www.russound.com 28-0112 10/07/04 Copyright © 2004 Russound®. All rights reserved.
