HD DIGITAL VIDEOCASSETTE RECORDER SRW-5000 SRW-5500 INSTALLATION MANUAL 1st Edition (Revised 3) Serial No. 10101 and Higher: SRW-5000 (SY) Serial No.
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.
For the customers in the Netherlands Voor de klanten in Nederland Hoe u de batterijen moet verwijderen, leest u in de Onderhoudshandleiding. Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA). Für Kunden in Deutschland Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen.
Table of Contents Manual Structure Purpose of this manual .............................................................................................. 2 Related manuals ......................................................................................................... 2 Trademark .................................................................................................................. 2 1. Installation 1-1. 1-2. 1-3. 1-4. 1-5. 1-6. 1-7. 1-8. 1-9. 1-10. 1-11. 1-12. 1-13. 1-14. 1-15.
Manual Structure Purpose of this manual This manual is the installation manual of the HD Digital Videocassette Recorder SRW-5000/5500. This manual is intended for use by trained system and service engineers, and provides the information that is required to install (environment, connection information, initial setting, etc.) and the setting check sheet. Related manuals Besides this “installation manual”, the following manuals are available for this unit.
Section 1 Installation 1-1. Installation Procedure 1-2. Supplied Accessories Installation procedure of this unit is shown on the following flowchart. Refer to each section about detail of each flow. The operation manual is also required to do *-marked flow. Operation manual Japanese ......................................................................... 1 English ........................................................................... 1 Operation manual CD-ROM (PDF) .................................
1-4. Power Supply 1-4-1. Voltage and Power Requirements This unit’s power line has a switching regulator. c Be sure to operate the unit within the range of following power voltage. Power voltage: AC 100 to 240 V ± 10 % Power frequency: 50 Hz or 60 Hz Power consumption: Maximum 320 W (With all of the presumed optional kits.) n The power consumption becomes the maximum at record-starting. Rush current: For customers in the U.S.A. and Canada: 1 Power cord 125 V 10 A (2.
1-5. Installation Space When installing, the installation space must be secured in consideration of the ventilation and service operation. . Do not block the ventilation slots at the left side and right side panels, and vents of the fans. . Leave a space around the unit for ventilation. . Leave more than 40 centimeters of space in the rear of the unit to secure the operation area. When the unit is installed on the desk or the like, leave at least four centimeters of space in the left and right sides.
1-6. Rack Mounting Explains how to mount this unit into a 19-inch standard rack. Be sure to mount this unit (*) into a rack accurately following the procedure and notes mentioned below. w . To prevent toppling over the rack, fix it on the horizontal and firm floor securely with bolts, etc. . When installing the unit in an Outside Broadcasting van, be sure to fix the unit to the rack using the screws and ornamental washers supplied with the rack mount kit. c . Use the specified rack mount rail.
Rack Mounting Procedure . Removing the feet 1. Set the unit its side panel down. 2. Remove the two screws and remove the lock plates. . Attaching the inner rails 5. Pull each inner rail from the two intermediate rails. 6. Pull each inner rail out of the intermediate rails while pressing each stopper. Intermediate rail Lock plate Inner rail Outer rail Press B3 x 6 Stopper Pull out Lock plate 3. Unscrew the four screws to remove the feet and spacers from the bottom plate of the unit. 4.
. Attaching the rack angles (handles) 9. Remove the four screws from both sides (left and right) of the unit. B4 x 6 . Loosely attaching the rail brackets 11. Slide the intermediate rail as shown in the figure, and then loosely attach the rear rail bracket to the outer rail with a plate nut (large) and the two screws. Plate nut (large) Rail bracket Outer rail Slide B4 x 8 Intermediate rail B4 x 6 n Keep these screws (B4 x 6).
. Attaching the outer rails 13. Loosely attach the two outer rails to the middle of the 5U space in the rack for mounting this unit, with the eight hexagon socket head cap screws, eight flat washers, and four plate nuts (small). 14. Check that the two intermediate rails attached to the rack are parallel.
. Mounting in rack c Be sure to carry the unit by the two persons or more. 18. Set each ball retainer to the position as shown in the figure in the direction of the arrow. Front side Intermediate rail Slide Ball retainer 19. Pull equal length of each rail on both sides out. 20. Lift the unit holding the gripes on both sides, slowly insert the inner rails into the intermediate rails. 21. While pressing each stopper of inner rails on both sides, slowly push the unit into the rack.
1-7. Matching Connectors and Cables When external cables are connected to the connector of this unit, the hardware listed below (or equivalents) must be used. Panel indication Matching connector (cable) Sony part No. TIME CODE IN CUE IN XLR 3P, MALE 1-508-084-00 AUDIO OUTPUT CUE OUT MONITOR OUTPUT TIME CODE OUT XLR 3P, FEMALE 1-508-083-00 REF. INPUT HD REF.
1-8. Signal Inputs and Outputs Reduced drawing of rear panel 1 2 3 5 4 Input connectors 1 TIME CODE IN XLR 3-pin x 1 Time code 0.5 to 18 V p-p, 10 kZ, balanced 1 CUE IN (SRW-5500 only) XLR 3-pin x 1 Analog audio +4 dBm (Standard) 600 Z termination, balanced (when ON) +4 dBu (Standard), high impedance, balanced (when OFF) 2 REF. INPUT 1 REF. INPUT 2 (OPTION) BNC x 4 (Loop through output x 2) External reference video signal HD : 0.6 V p-p, 75 Z, sync negative (HD analog tri-level sync) SD : 0.
Output connectors 1 AUDIO OUTPUT XLR 3-pin x 4 (1 set : CH1, CH2, CH3, and CH4) Analog audio +4 dBm (Standard) (600 Z load), low impedance, balanced 1 CUE OUT XLR 3-pin x 1 Analog audio +4 dBm (Standard) (600 Z load), low impedance, balanced 1 TIME CODE OUT XLR 3-pin x 1 Time code 2.2 V p-p, low impedance, balanced 1 MONITOR OUTPUT XLR 3-pin x 2 (1 set : L and R) Analog audio +4 dBm (Standard) (600 Z load), low impedance, balanced 2 HD REF. OUT BNC x 2 0.
REMOTE 2 PARALLEL I/O: 50-pin (female) External view 17 1 33 18 50 34 Pin No.
(Continued) Pin No.
VIDEO CONTROL: 9-pin (female) External view 5 USB: USB series B Standard : USB standard Ver1.1 1 9 External view 6 2 1 3 4 Pin No. Signal Pin No. I/O Signal 1 GND 1 – Vcc (+5 V) 2 RM TX (_) 2 I/O DATA (_) 3 RM RX (+) 3 I/O DATA (+) 4 GND 4 – GND 5 —— 6 GND 7 RM TX (+) 8 RM RX (_) 9 GND 1-9. Switch Settings on Connector Panel ETHERNET: RJ-45 modular jack Standard : Complied with IEEE 802.3u (100BASE-TX) and IEEE 802.
1-10. Switch Settings on Circuit Boards 1-10-1. APR-62 Board If necessary, perform the following audio-related settings using the switches on the APR-62 board. . Analog audio output level/output headroom . Monitor output level/output headroom m . Refer to Section 1-15 for removing and reattaching the plug-in boards. . The switches S400, S701, S6100 are Factory use. Never change the setting. A B C D E F G S701 1 S6100 (Board No.
1-10-2. CUE-13 Board If necessary, perform the following audio-related settings using the switches on the CUE-13 board. .
1-11. System Setting 1-11-1. Setting the System for SRW-5000 1. Activating the system menu (1) Turn on the power. (2) Press the DIAG button while pressing the [SFT] (SHIFT) key. (3) Press the [F8] (MAINTE EXEC) key while pressing the [SFT] (SHIFT) key. (4) Press the [F9] (OTHERS CHECK) key. (5) Press the [F9] (SYSTEM MENU) key to display the system menu. 2. Setting the system Set the system referring to the table “1-11-3. Compatibility of REC and PB”.
(3) Press the [F2] (SYSTEM SCAN) key several times for setting to the Interlace, Progressive or PsF (Progressive Segmented Frame). F1 F2 F3 F4 SYSTEM LINE 1080/59.94i 422 YPbPr LINE 1080 SYSTEM [F1]SYSTEM Interlace [F2]SYSTEM SCAN MODE Interlace SCAN [F3]SYSTEM FRAME 29.97Hz PsF Progressive SIGNAL MODE 422 SYSTEM [F4]SYSTEM FRAME [F6]FRAME CONVERT 1080/59.
3. Check the setting Check that the content of system setting performed after saving is displayed with white characters in the first line of the system menu. Check further that the items to be updated from the current system setting are displayed with yellow characters to the right of respective setting items. n The faint white characters in the first line of the system menu mean that a combination of unsettable system items is selected.
1-11-2. Setting the System for SRW-5500 1. Activating the system menu (1) Turn on the power. (2) Press the DIAG button while pressing the [SFT] (SHIFT) key. (3) Press the [F8] (MAINTE EXEC) key while pressing the [SFT] (SHIFT) key. (4) Press the [F9] (OTHERS CHECK) key. (5) Press the [F9] (SYSTEM MENU) key to display the system menu. 2. Setting the system Set the system referring to the table “1-11-3. Compatibility of REC and PB”.
(3) Press the [F2] (SYSTEM SCAN) key several times for setting to the Interlace, Progressive or PsF (Progressive Segmented Frame). F1 F2 F3 F4 DIAG ALT SYSTEM LINE SYSTEM MENU 1080/59.94i 422 YPbPr HDCAM-SR LINE 1080 SYSTEM [F1]SYSTEM Interlace [F2]SYSTEM SCAN MODE Interlace SCAN [F3]SYSTEM FRAME 29.97Hz PsF Progressive SIGNAL MODE 422 SYSTEM [F4]SYSTEM FRAME [F6]FRAME CONVERT 1080/59.
3. Check the setting Check that the content of system setting performed after saving is displayed with white characters in the first line of the system menu. Check further that the items to be updated from the current system setting are displayed with yellow characters to the right of respective setting items. n The faint white characters in the first line of the system menu mean that a combination of unsettable system items is selected.
1-11-3. Compatibility of REC and PB The selectable systems differ according to the VTR settings (operation mode) or option boards. System setting (Operation mode) SYSTEM SYSTEM SYSTEM SYSTEM (FRAME) SIGNAL LINE SCAN FREQ [Hz] 23.98 PsF 4:2:2 1080 24 (YPbPr) 25 29.97 30 Interlace 25 29.97 30 Progressive 50*1 720 59.94*1 23.98, PsF 4:4:4 1080 24, 25, (RGB) 29.97, 30 (HKSRInterlace 25, 5003) 29.97, 30 System setting (Operation mode) SYSTEM SYSTEM SYSTEM SYSTEM (FRAME) SCAN SIGNAL LINE FREQ [Hz] 23.
1-11-4. Setting to Store Meta Data Perform the setting to store meta data. 1. Activating the meta data setup menu (1) Turn on the power switch. (2) Press the DIAG button while pressing the [SFT] (SHIFT) key. (3) Press the [F8] (MAINT EXEC) key while pressing the [SFT] (SHIFT) key. (4) Press the [F9] (OTHERS CHECK) key. (5) Press the [ALT] key. (6) Press the [F1] (META DATA) key. The format selection menu appears.
In selecting [F2] (HDCAM-SR) on SRW-5000, or SRW-5500 3. Setting the meta data line (1) Move the cursor to the item to be set using the [(]/[)] keys. (2) Perform the line setting using the [F8] (PLUS)/[F9] (MINUS) keys, MULTI CONTROL knob, or the [&]/ [*] keys.
In selecting [F3] (HDCAM) on SRW-5500 5. Setting the meta data 3 packet (1) Move the cursor to the item to be set using the [(]/[)]/ [&]/[*] keys. (2) Perform the line setting using the [F8] (PLUS)/[F9] (MINUS) keys or the MULTI CONTROL knob.
In selecting [F4] (DOWN CONV.) on SRW5000, or SRW-5500 7. Setting the meta data line of down convert output (1) Move the cursor to the item to be set using the [(]/[)] keys. (2) Perform the line setting using the [F8] (PLUS)/[F9] (MINUS) keys, MULTI CONTROL knob, or the [&]/ [*] keys. F1 NVRAM CTL DC OUTPUT META DATA LINE SELECT Meta Line1(HDCAM-SR) : OFF Meta Line2(HDCAM-SR) : DC Line 18 Meta Line3(HDCAM-SR) : DC Line 19 F2 m .
1-11-5. Input/Output Phase Settings Perform phase settings for various inputs and outputs. n The phase setting procedure of SRW-5500 is the same as that of SRW-5000. 1. Activating the phase set menu When OTHERS CHECK menu is displayed: (1) Press the [F2] (PHASE SET) key to display the PHASE SET menu. When a menu is not displayed: (1) Turn on the power switch. (2) Press the DIAG button while pressing the [SFT] (SHIFT) key. (3) Press the [F8] (MAINT EXEC) key while pressing the [SFT] (SHIFT) key.
(3) Press the [F4] (AU PB OUT) key several times to set the playback audio output phase (OFF or _1FRAME). OFF: Outputs in the same phase as reference signal. _1FRAME: Outputs one-frame ahead of reference signal. F1 NVRAM CTL OTHERS CHECK (5) Press the [F6] (TC INPUT) key several times to set the record time code input phase (OFF or +1FRAME). OFF Records in the same phase as reference signal. +1FRAME: Records with one-frame delay of reference signal.
(7) Press the [F8] (LTC OUT) key several times to set the LTC output phase (LINE or FC). LINE: Outputs in the same phase as the main line. FC: Outputs in the same phase as FC output. F1 NVRAM CTL F2 HD SDI OUT F3 SD SDI OUT OTHERS CHECK PHASE SETTING F4 AU PB OUT DIAG AUDIO INPUT ALT F5 HD SDI OUTPUT ADV. SD SDI OUTPUT ADV. AUDIO PB OUTPUT ADV.
2. Displaying SYSTEM BANK menu (1) Press the DIAG button while pressing the [SFT] (SHIFT) key with the HOME menu. (2) Press the [F8] (MAINTE EXEC) key while pressing the [SFT] (SHIFT) key. (3) Press the [F9] (OTHERS CHECK) key. (4) Press the [ALT] key. (5) Press the [F5] (SYSTEM BANK) key to display the SYSTEM BANK menu. Window Description The left item [C] shows the current settings, the right items 1 to 8 show system bank data, and [F] shows factory settings.
4. Reading the settings from the system bank n No data can be read from the system bank in the standby mode or while a tape is loaded in the unit. Eject the tape and confirm that the standby mode is set to off before reading data. (1) Press the [F8] (DIRECTION) key with the SYSTEM BANK menu, and choose direction. The left cursor bar blinks. (2) Position the lighting cursor bar at a bank number (1 to 8) for reading with the [(]/[)] keys. (3) Press the [F9] (COPY) key. A confirmation message appears.
2. Displaying SYSTEM CARD BANK menu (1) Press the DIAG button while pressing the [SFT] (SHIFT) key with the HOME menu. (2) Press the [F8] (MAINTE EXEC) key while pressing the [SFT] (SHIFT) key. (3) Press the [F9] (OTHERS CHECK) key. (4) Press the [ALT] key. (5) Press the [F6] (SYSTEM CARD) key to display the SYSTEM CARD BANK menu. Window Description The right item shows the data of the unit, [C] shows current settings, 1 to 8 show system bank data, and [F] shows factory settings.
3. Memory Stick format m . No Memory Stick can be used unless it is formatted by the unit. Format a Memory Stick to be used before storing the system settings. . When a Memory Stick is formatted, its data is cleared completely. (1) Press the [F1] (FORMAT CARD) key with the SYSTEM CARD BANK menu. A confirmation message appears. To cancel formatting Press the [CLR] (CLEAR) key while the confirmation message is displayed. (2) Press the [F1] (FORMAT CARD) key while pressing the [SFT] (SHIFT) key.
To collectively read eight pieces of system bank data stored in a Memory Stick Press the [F7] (SELECT ALL) key. n If any protected bank number exists in the system bank, the [F7] (SELECT ALL) key cannot be selected. (4) Press the [*] key to move to the right (unit data side), and position the blinking cursor bar at the bank number of the save origin (unit system bank) using the [(]/[)] keys. To update the current system settings Position the blinking cursor bar at the item [C].
1-11-9. Checking Saved System Bank Data in Detail The data stored in the system bank is the settings of the SYSTEM menu, META DATA SETUP menu, and PHASE SET menu. Details of the settings and the current system settings of the unit can be checked in the following procedure. n Refer to the following for the setting of each menu. . SYSTEM menu: Section 1-11-1 (SRW-5000) Section 1-11-2 (SRW-5500) . META DATA SETUP menu: Section 1-11-4 .
1-12. Opening/Closing the Lower Control Panel Close the Lower Control Panel Open the Lower Control Panel 1. While lifting the outer stays by the forefinger, close the lower control panel as shown in the figure. 2. Reinstall the lock plates removed in step 1 of the opening procedure. 1. If the lock plates are attached, remove the two screws and remove the lock plates. n When no lock plate is attached at the start, this operation is not necessary. Lock plate B3 x 6 Lock plate Outer stay 2.
1-13. Reference System For each reference signal of this unit, either of an external reference video signal from the REF. INPUT 1 connector or input video signal from the HD SDI INPUT A connector is automatically selected according to the setting of setup menu ITEM-005, and the operation mode (PB/EDIT/REC) of this unit. (Refer to the table 1-13-1 below.) n When the setup menu ITEM-005 is set to “external”, be sure to input the external reference video signal to the REF. INPUT 1 connector.
1-14. Settings when Editor is Connected 1-14-1. Settings for Time Code To set the TIME CODE, use the TC menu in the function menu. Set the TIME CODE as follows when the editor or the VTR with edit function is connected. Button Item Setting F6 REGENE SOURCE int-L F7 TCG MODE preset F8 RUN MODE free 1-14-2. VTR Constant Values Settings of Editor Set the VTR constant values according to the table 1-14-2 below when the editor which needs the setting of VTR constant values is connected. Table 1-14-2.
1-15. Removing/Reattaching Plug-in Board m . Turn off the power and unplug the power cord before removing/reattaching the board. . When the plug-in board is replaced, refer to the maintenance manual, volume 1. 4. Fully loosen the two fixing screws. 5. Remove the upper lid (rear) assembly by moving in the direction indicated by the arrow. Fixing screw Fixing screw Upper lid (rear) assembly Portion Removing Square hole 1. Fully loosen the fixing screw. 2.
Reattaching When reattaching the board, install in the reverse order of removal. m . After inserting the board, push in the two folded eject levers simultaneously to firmly connect the plug-in board to the connector on the motherboard. . When reattaching the upper lid (rear) assembly, be sure to insert the protrusions in the square holes on the chassis, and then secure the lid. . Tighten the fixing screws as following torque. Tightening torque: 120 x 10 _2 N.m {12.2 kgf.cm} 1-16.
4. Release the lock of the board holder and open the AE31 board in the arrow direction. 5. Check by eye that the unit is in the state to be able to take up manually the tape. 6. Pull the ME wire for a few times with short steps to take up the tape inside the cassette. m . Be careful for the tape not to catch in parts such as a flange of a tape guide. . Don’t take the ME wire off the wire holder. . The ME wire links with the T real table.
Appendix A Setting Check Sheet It is recommended to copy these check sheets and write down the setup conditions (switch and so on) under the application. If the setting is changed temporarily by changing operating condition, the setting can be reset easily. For the setup menu, store the setting values to the Memory Stick (Memory Card) before check, maintenace and repair. (Refer to the operation manual.) It is recommended to attach the sheets to the unit when check, maintenance and repair.
Setting Check Sheet Connector panel Switch Factory setting Setting Reference video input 1 75 Z ON [||] ON [||] OFF Reference video input 2 75 Z ON [||] ON [||] OFF CUE input 600 Z ON [||] ON [||] OFF Switch Factory setting Setting REMOTE 1 (9P) LOCAL [||] Lighting (REMOTE) [||] OFF (LOCAL) REMOTE 2 (50P) LOCAL [||] Lighting (REMOTE) [||] OFF (LOCAL) SRW-5500 only Upper control panel Switches on the board n Never change the setting of Factory use switches.
Setting Check Sheet CUE-13 CUE audio output level — S100 (SRW-5500 only) — S101 Factory setting Setting O N Switch No. dBm/600 Z) +4 dBm/600 Z 1 2 3 4 1 2 3 4 O N ( O N +4 dBm/600 Z 1 2 3 4 Channel O N Name 1 2 3 4 Board ( dBm/600 Z) n The following switches are Factory use. Never change the setting.
Switch No.
The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation.
SRW-5000 (SY) SRW-5500 (SY) E 3-791-086-04 Sony Corporation Printed in Japan 2005.
