PORTABLE BRUSH CUTTER RURIS 425/435
PORTABLE BRUSH CUTTER RURIS 425/435 Table of Contents Introduction 2 Essential Checks before Commissioning and During Operation 3 Labor Protection 5 Composition of the Ruris Portable Brush Cutter 6 Technical Characteristics 7 Installation of the Brush Cutter425/435 8 Commissioning 13 Necessary Checks In Case the Ruris Portable Brush Cutter Is Unresponsive 16 Operation of the Brush Cutter 16 Types of Knives 20 Maintenance After Running In 20 Maintenance Table 21 Movement 22 Packing
Introduction Thank you for choosing the RURIS product andwelcome to our client group. We are confident that you will be satisfied with our product for its performance and easy operating mode. Our experience in the field and the use of high quality materials led to the manufacture of efficient products that will meet your demands for many years if you follow the recommendations for use and maintenance.
1.0 Essential Checks before Commissioning and During Operation Make sure that: 1. The circuit of the emergency stop lever is properly assembled. 2. Oil quantity from the engine bath for the brush cutter 425: 100ml 3. Oil quantity from the engine bath for the brush cutter 435: 120ml 4. The oil used is Ruris brand: Ruris 4T/ 10W30-APISJ/CH 5. Running in must be made at idle and not under load. Three tanks of gas at idle, no-load. 6.
Attention! When you mount the cutter disc, use the lock to unfasten the clamp nut and the retainer clockwise. After mounting the cutting disc make sure that the nut is properly tightened and the cutting disc is securely attached and there is not any warping or cracking on the surface of the cutting disc. Fig. 1.2 9. Operating the mowing head is made by operating the throttle lever at maximum. 10. Fill with graphite grease the mowing head, with around 20 grams. 11.
1.
1.2 Composition of the Ruris Portable Brush Cutter The portable brush cutter Ruris 425/435 consists of the following elements: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. engine handle protection case starter roll cutting disc throttle handle switch on/off command mowing head electrical wiring air filter cover exhaust muffler set point of the handles handlebar chassis dual balance harness Fig.
1.3 Technical Characteristics Brush cutter 425 Brush cutter 435 Engine manufacturer Product Honda Honda Country of origin of the engine Japan Japan Engine horsepower (HP) 1 1.3 Cubic capacity (cm³) 25 35.8 Engine duty cycle (stroke) Ignition coil Startup 4 4 electronic electronic manual manual Unleaded gasoline Unleaded gasoline Engine oil bath capacity (ml) 100 120 Fuel tank capacity (ml) 530 630 Fuel consumption (l/h) 0.54 0.
1.4 Installing the Ruris 425/435 brush cutter Before installing and commissioning, you should make sure that the Ruris Brush Cutter is properly assembled according to the plan of composition of point 1.2 and respect the instructions from this manual. Only then can you proceed to the actual commissioning. Installation 1.4.1 Throttle lever Install the throttle lever on the right handle, according to fig.
Perform 2-3 operation maneuvers of the throttle lever and check if the cable slides from the minimum to the maximum race of the throttle lever fixed on the engine fig 4. Fig. 4 Also check the on off switch NOTE: Do not attempt at cancelling or blocking the emergency stop lever because you risk injuring the people located near you or putting your life in danger. 1.4.2. Handle assembly Loosen the screw located on the chassis guide by unfastening it until it is free from the thread, according to fig. 5 Fig.
Bring closer the two handles and place them face to face oriented ahead according to fig 6. Fig. 6 Gently tighten the fixing screw of the handles and orient them on a neutral position, fig 7. Fig.
1.4.3 Cutting disc installation In order to install the cutting disc you will first need to unfasten the safety nut. To do this properly you will need the following tools: the lock and the lever key supplied with the brush cutter. Use the lock supplied with the Ruris brush cutter and place it in the locking hole from fig 8. Fig. 8 Use the key supplied with the Ruris brush cutter, secure the safety nut and rotate clockwise to unfasten according to fig 9 Fig.
Fig. 10 Check that all the assembly is correctly assembled and that the disc is tightly fastened without axial or transversal play. If you fail to do this, you must immediately go to the nearest authorized Ruris Service point to remedy this problem. 1.4.4 Assembling the mowing head protection Assemble the mowing head protection in the attachment points indicated on the chassis guide. Attention! Do not use the Ruris brush cutter without this protection.
To balance the brush cutter in relation to the harness and the user‟s height, you will need to perform the following maneuvers: make sure that the mounting strap is located at a hand breadth under the user‟s hip Place the brush cutter in the harness‟ safety and release it If the brush cutter does not stay balanced and touch with the cutting disc the ground surface or if the brush cutter tends to be inclined from the engine, you will need to reposition the securing system placed on the brush cutter guide tow
Fig. 13 2.1 Engine startup Place the brush cutter horizontally on the ground Prime the carburetor with petrol by 3 successive presses of the petrol pump The throttle handle and the switch are correctly placed for startup Place the air flap in the “open” position according to fig. 13 Fully push the throttle lever (Fig. 14.1) Push the block button (Fig. 14.2) Fig. 14.1 14 Fig. 14.2 Switch the switcher on “Start” position Fig. 14.
Secure tightly the guide of the brush cutter with your left hand and boldly pull the starter rope with your right hand. Pulling the rope must be made in two steps. The first step will be made by an easy pull of the starter until the rope has come out of the starter roll about 150-200mm and you can fill the engine compression. The second step will be pulling powerfully and greatly without interruption (pull the starter rope until the level of your shoulders) according to fig.
3.0 Necessary checks if the Ruris brush cutter does not answer to commands When the engine does not start: 1. Check if the ignition is ON. 2. Check if there is enough fuel. 3. Check if there is enough petrol in the tank. 4. Check if the petrol reaches the carburetor. 5. Check if the sparkle plug gives any sparks. 6. Check if the fuel is older than 2 weeks because it risks losses of octane.
After you have started the brush cutter and have placed it in the harness‟ safety lock, you can proceed to operation. For your safety avoid contact between the cutting disc and stones or hard objects. For a correct operation you can apply various mowing methods: 1. Spiral mowing method or number 9 Start mowing from the most outward points of the surface, at the same time choose your mowing mode; you can cut from the right or from the left.
3. The method of mowing on slopes or ramps Avoid mowing directed to slope or ramp. In order to mow safely place yourselves perpendicularly on the axis of the slope and always lean yourself on the foot from the ramp, according to fig.18 Fig. 18 4. The mowing method used for clearing (fig. 19) Clearing is always made with a perfectly chosen disc, depending on the shrubs that need to be cleared.
5. The mowing method using the AutoCut mowing head To use the AutoCut mowing head you must perfectly choose the type of thread for the surface that needs to be ventilated or mowed. The thread that equips the AutoCut will finely mince the grass. The AutoCut can be successfully used in areas with obstacles to ventilate trees, in the areas of joints with borders. To handle the thread you will need to operate the AutoCut by pressing it on the ground or by gently tapping it of the ground, according to fig.
5.0 Types of knives Autocut Cutting head with 2 threads whose length can be set depending on the cutting length that you wish to achieve.It is especially used at mowing and organization works, in places with obstacles. Knife with 3 teeth Made out of steel, intended for the mowing works of rough and dry grass, on large areas. Knife with 4 teeth Made out of steel, intended for removing the rough grass and thorn bushes, on large areas. 6.
7.
8.0 Movement When you wish to move the Ruris brush cutter on short or long distances, always dismount the cutting blade to avoid possible accidents or damages to it. 9.0 Packing Packing is made in closed cardboard boxes. Packing dimensions 425 435 length (cm) 184 184 width (cm) 28 28 height (cm) 32+13 32+13 weight (kg) 7,0 7,5 10.0 Storing 22 The brush cutters should be stored in dry places, roofed and protected against moisture, in rooms with windows and adequate ventilation.
11.0 Warnings The engine should be turned off when performing supply and lubrication. After stopping for refill, wait 15 minutes before starting again. Continuous usage is forbidden. People younger than 18 years old are not allowed to use this brush cutter. Any person that does not know and has never used the multifunctional equipment should read the user manual before working with the product.
DECLARATIONS OF CONFORMITY 24
25
