User Manual

TheSetupFailures menu openstheSetupFailuresmenu,which  lets youselectfrom arangeofdifferent problems
thatcanoccur onyourmodelduring flight. Youcanthenpracticerecovering fromtheseincase they wereever to
happeninareal‐lifesituation.
The main section of this menu is a table displayin g the available failures, when they should  happen, and some
furthersettingscontrollingtheirbehaviourwhentheydooccur.
TheavailableFrequencysettingsareasfollows:
• Never(Default)–Disablesthisfailure,thefailurewillnotoccur.
• Randomly–Thefailurewilloccurrandomlyinsideafewminutes.
• Aftertake‐off–Thefailurewilloccurshortlyafteryourmodelleavestheground.
• After10s–Thefailurewilloccurapprox.10secondsafteryourmodelleavestheground.
• After30s–Thefailurewilloccurapprox.30secondsafteryourmodelleavestheground.
• After1min–Thefailurewill occurapprox.1minuteafteryourmodelleavestheground.
• After5mins–Thefailurewilloccurapprox.5minutesafteryourmodelleavestheground.
Theavailablefailuresareasfollows:
• Engine – This option lets you setup an engine failure. Choose from one of the frequency options to set
if/when the failure will occur, and choose either Random Engine to make a s ingle engine fail on a multi‐
engined model (on a single engine model this is the same aschoosingAllEngines), orselectAllEnginesto
makeallpresentenginesfail.
• Elevator/Cyclic‐pitch– Thisoptionletsyousetupa  failureoneithertheelevatorservo(fixed‐wingmodels)
orthecyclic‐pitchservo(helicopter  models). Choosefromone of the frequency options to set if/whenthe
failurewilloccur, andchooseeitherStick atMinto maketheservo move andstayattheminimumtravel,
Stick at Max to make the servo move and stay at the maximum travel, Stick at centre to make the servo
move and stay at the central position, or Stick at last input to make the servo stay at the position it is in
whenthefailureoccurs.
• Aileron/Cyclic‐roll – This option lets you setup a failure on either the aileron servo (fixed‐wing models) or
thecyclic‐rollservo(helicoptermodels).Choosefromoneofthefrequencyoptionstosetif/whenthefailure
willoccur,andchooseeitherStickatMintomaketheservomoveandstayattheminimumtravel,Stickat
Maxtomaketheservomoveandstayatthemaximumtravel,Stickatcentretomaketheservomoveand
stay at the central position, or Stick at last input to make the servo stay at the position it is in when the
failureoccurs.
• Rudder/Tail‐rotor–Thisoptionletsyousetupafailureoneithertherudderservo(fixed‐wingmodels)orthe
tail‐rotorservo(helicoptermodels).Choosefromoneofthefrequencyoptionstosetif/whenthefailurewill
occur,andchooseeitherStickatMintomaketheservomoveandstayattheminimumtravel,StickatMax
tomaketheservomoveandstayatthemaximumtravel,Stickatcentretomaketheservomoveandstayat 
the central position, or Stick at last input to make the servo stay at the position it is in when the failure
occurs.
ClicktheResetbuttontoresetallfailurestothe“Never”frequencystate,disablingthem.

Onceyou havesetupyourfailuresto yoursatisfaction,click theAccept buttonto setthemand returntothe Main
View.Alternatively,clickCanceltoreturnwithoutchanginganysettings.


Reset