GPS Watch with Heart Rate Measurement Operating instructions Edition 11/2013
Table of Contents 1 2 3 4 5 6 Application range................................................................................ 4 Safety and maintenance ..................................................................... 5 2.1 Safety instructions ........................................................................... 5 2.2 Repairing .......................................................................................... 6 2.3 Water impermeability ..................................................
7 8 9 10 11 12 13 14 15 6.3.3 Training ................................................................................. 37 6.3.4 After training ......................................................................... 41 6.4 GPS-Navigation-mode.................................................................... 43 6.4.1 Navigation-display ................................................................ 43 6.4.2 Go-to-display......................................................................... 48 6.
1 Application range The GPS-watch RUNGPS1 is equipped with a navigation system. The User’s location can be determined by using the satellite network that surrounds the earth. This is possible at any moment and everywhere in the world. The GPS-watch is destined for the use as a global system for determining the location.
2 2.1 Safety and maintenance Safety instructions Please read this chapter carefully and follow all the specified indications. This way you ensure the adequate functioning and a long period of operation for your GPS-watch. Keep the wrapping and operating instructions well, so that, in case of alienation, you can hand them on to the new owner. For safety reasons, do not operate the GPS-watch while driving a car. Stop or let a co-passenger carry on the settings.
latter as to how the device should be used. Children should be supervised in order to ensure that they do not play with the device. Important: Always consult your doctor, before starting a regular training program. The RUNGPS1 watch is not a medical device; it is a helping training gadget for the measurement and display of your cardiac frequency. Wearers of cardiac pacemakers may use devices for cardiac frequency measurement only after consulting with their doctor.
Be careful not to touch the buttons, when the watch is still moist. The water only can enter in the case through these buttons and this can affect the watch. Please note that salty and thermal water can lead to the corrosion of the metallic elements. Note that, in case of extreme temperature differences (e.g. from sauna to the swimming-pool, from the beach to cold sea) water resistance can not be guaranteed.
2.6 Environmental temperature The GPS-watch can be operated durably at an environmental temperature from 0 °C up to 50 °C, and stored at an environmental temperature of -10 °C up to 60 °C. Avoid high temperatures (e.g. in stopped vehicles or under direct sun influence) and permanent environmental humidity. Indication: Display problems at temperatures of -10° C up to 0° C will not be attributed to the GPS-watch, but on the impairment of accumulators due to coldness.
Charge the accumulator of the GPS watch only with a USB cable delivered together with it. If the accumulator is charged otherwise, this can lead to overheating, explosion or fire. Do not charge the accumulator of the GPS watch near heat sources or in a car, under the powerful action of sunbeams. Powerful temperature leads to the destruction of the accumulator and may lead to overheating, explosion or fire.
Information regarding the replacement of the battery of chest strap can also be found at point 9.2 "Replacement of the battery of chest strap ". 2.8 Disposal Batteries are special waste. For the adequate disposal of the batteries, there are special containers in the shops where batteries are commercialized, as well as in the communal collection places.If you want to throw the GPS watch and its accessories away, eliminate them in conformity with current dispositions.
Clean the GPS watch and chest strap only with a soft, moist towel without naps. Do not use diluent, corrosive cleaning agent or under the form of gas. Be careful not to leave water drops on the display of the GPS watch. Water may cause permanent stains. Do not expose the display to sunlight, or to direct action of ultraviolet beams. 2.
Elastic strap: 1 USB cable 1 bike support incl. 2 cable clamps and 1 installing plate 3.2 Functional press keys „ST./STP.
Contact points for USB cable 4 Start-up We recommend you to read the operating instructions carefully before starting-up the GPS watch. On the screen of the GPS watch there is a protection film. Eliminate it before the first use. Caution! This protection film for the screen must be kept out of reach of babies and young children! It presents asphyxiation danger! The watch will be delivered in off-line mode. Press and keep the “LAP/RESET”-button pressed for approx.
The GPS watch can be worn as a watch or can be fixed on the slide bar of your bike by means of the delivered support. Fixation by bike support. Put the bike support on the slide bar of your bike. Use the delivered installing plates, if the support is too weak. Additionally, you can fix the support with a cable binder. Fix the watch on the bike support.
4.1 Keypad Lock By pressing the "Light" and "View" buttons at the same time, you can activate or disable the keypad lock. When the keypad lock is activated before your training, you can avoid accidentally pressing keys during your workout. When the keypad lock is on you can change, with the "View" button in workout mode, between three display options. Keypad lock activated 4.2 Keypad lock disabled Charging the accumulator of the GPS watch The GPS watch has a lithium-polymer accumulator.
Fix the clip of the USB cable on the GPS watch according to the following image and put the USB cable to a USB port of your computer coupled to the power. The installation of a driver for charging the accumulator is not necessary. During the charging process, the following symbol appears on the screen: if the accumulator is fully charged, the display "battery full" appears. 4.
Join the elastic strap with the sensor. Put the elastic strap so that the sensor stays on the chest, under the pectoral muscles. In order to make an optimum transfer of the cardiac frequency possible, wear the belt with the battery compartment on the right side (from the wearer’s point of view). To ensure a good contact with the skin, you must moist the contacts of the sensor or use an ECG gel (available in medical shops).
The reception of the signal, without problems, from a satellite can only be guaranteed under calm weather conditions (clear sky) and an adequate reception area – open area with clear view to the sky. Because satellite signals react very sensitively to external influences, bad weather (e.g.
Additionally, there is an adjustment mode, for which the following apply: Call of adjustment mode: Press the „MODE“-button and hold down Settings of adjustment mode: Press the „ST./STP.
By Dist LapWP Alert o View Scan o Track Log o Delete Del Last Del All • Navigation (Point 6.4) o Sel Path o Del Path o Nav Mode o WP Radius • GPS (Points 6.3 and 6.4) o On/Off o Timeout o A-GPS • HRM (Point 6.
o Max.HR o Pairing Setting of maximum cardiac frequency Junction of the chest belt with the GPS watch • Settings o Timer (Point 6.2) Timer adjustment o Alarm (Point 6.2) Alarm adjustment o Time Date (Point 6.2) Home Time GPS Upd Setting of GPS updating time Time Zone Time zone adjustment Manual Manual adjustment of time Dual Time Dual time adjustment Format Adjustment of 12/24 hour format o User (Point 6.1.
Calibrate Language Sys Reset • Memory (Point 6.1.3) Compass calibration Language adjustment Operation of system reset Call of memory status Some general settings (user’s settings, system setting operation and call of memory status), which are not presented directly in the chapters Time mode, GPS-Workout-mode, GPS-Navigations-mode and Compass-mode, are described here: 6.1.1 User’s settings These data are necessary for calculating the calorie consumption, the maximum cardiac frequency respectively.
6.1.2 System settings Activation/deactivation of key tones In the setting mode select „Settings“ point from the menu „System“ „Sound“ „Key Tones“. Then select "On" in order to activate key tones or "Off" to deactivate them. Activation/deactivation of fixed time alarm In the setting mode select „Settings“ point from the menu „System“ „Sound“ „Chime“. Then select "On" in order to activate fixed time alarm or "Off" to deactivate it.
Then select „0’00’00.00 N” for the indication in Degrees-MinutesSeconds or „0.000000 N” for the indication in decimal degrees Adjustment of the unit of measure for body weight In the setting mode select „Settings“ point from the menu „System“ „Units“ „Weight“. Then select „kg” for the indication in kg or „lb” for the indication in Pfund Language adjustment In the setting mode select „Settings” point from the menu „System“ „Language“.
The memory use level of the GPS watch will be indicated in %. 1% of the memory corresponds to approximately 480 in memorized reference points for the GPS watch. CAUTION: Keep in mind that the watch does not delete automatically the memory with your data. To this effect, when transferring the data from the watch in your computer, you must activate automatic memory deletion at a data transfer from Runtastic Connect, in settings/options.
• Alarm • Dual Time 6.2.1 Time and date In Time-mode press the „VIEW” button until the following display appears on the display: Day of the week Time Month Date Update GPS for time: In the setting mode select „Settings” point from the menu „Time Date“ „Home Time“ „GPS-Upd“. Then select "ON" or "OFF". "ON" is pre-set, this means that when the satellite signal is received, time and date will be automatically set.
calculate the time zone based on the established longitudinal degree. If this does not work properly, set the time one in hours (e.g.: + 1:00). Adjustment of 12/24 hour format In the setting mode select „Settings” point from the menu „Time Date“ select „Format“. Then select between the format of 12 or 24 hours.
6.2.3 Timer In Time-mode press the „VIEW” button until the following display appears on the display: Timer Current time Timer adjustment In the setting mode select „Settings” point from the menu select „Timer“. Then adjust the hours, minutes and seconds for the timer. Timer use: In the display mode Timer press the „ST./STP" button to start or stop the timer. If the timer is stopped, press the "LAP/RESET" button, to reset the timer at the time set previously.
6.2.4 Alarm In Time-mode press the „VIEW” button until the following display appears on the display: Alarm 1-5 Alarm time Alarm „ON” „OFF” Alarm format Press the „ST./STP.” button, to select the alarm 1-5. Press the „LAP/RESET” button to set the alarm "ON" (enabled) or "OFF" (disabled). Setting of alarm time and alarm format: In the setting mode select „Settings” point from the menu select „Alarms“. Then select from alarms 1-5 and adjust alarm hours and minutes, "ON/OFF" will blink.
Then select the desired alarm format. Alarm stop: When the alarm rings, you can stop it by pressing any key. 6.2.5 Dual Time By this function you can choose a dual time. In Time-mode press the „VIEW“button until the following display appears on the display: Dual time Current time Dual time adjustment: „Time In the setting mode select „Settings” point from the menu Then adjust the desired difference (from the current time to dual time) in 30-minute steps. Date” „Dual Time”. 6.
Training data row 1 Training data row 2 Training data row 3 Within the GPS-Workout-mode the speed, distance, training time, cardiac frequency and other interesting data are indicated; these can be subsequently seen on the computer by Runtastic Connect. GPS-Workout-mode works in tight connection with GPS-Navigation-mode. The functions start and stop training and lap time taking can be achieved in both modes. 6.3.
% of the maximum cardiac frequency Above the training zone Upper limit Within the training zone Lower limit Under the training zone Selection of training zone In the setting mode select „HRM” point from the menu „HR Zone“ Then select one of the three preset training zones of the training zone defined by the user (User). „Select“.
Reset of upper and lower limits to basic setting In the setting mode select „HRM” point from the menu „HR Zone“ „Reset“. Setting of maximum cardiac frequency In the setting mode select „HRM” point from the menu „Max.HR” and adjust the specific maximum frequency. Alarm activation for training zone In the setting mode select „HRM” point from the menu „HR Zone“ „Alert“ „On“.
6.3.2 Profiles and training data The GPS watch has 5 different training profiles: Running, Cycling, Hiking, Sailing and „User“ The parameters of the respective profile (3 values per workout) may be set both via Runtastic Connect and directly on the GPS watch. The profile, however, can only be changed on your watch. Selection of training profile In the setting mode select „Workout“ point from the menu „Profiles“ „Select“. Then select one of the five training profiles.
Possible training data rows 1 and 3 Altitude Calories Distance Heading HR-Avg HR-Max HR-Min HR HRZ-Abv HRZ-Blw HRZ-In LapDist LapNo LapTime Pace Avg Pace Max Pace Speed Avg Speed Max Speed TimeOfDay Wkout Time Altitude Calories Distance Heading (degree indication) Average cardiac frequency Maximum cardiac frequency Minimum cardiac frequency Current cardiac frequency Time above training area Time below training area Time in training area Lap distance Number of laps Time of laps Medium Pace (time/km) Maximum
Possible training data row 2 Distance HR LapDist LatLong PaceAvg SpeedAvg Speed TimeOfDay Wkout Time Distance Current cardiac frequency Lap distance Longitudinal and latitude degree Average pace (time/ km) Average speed Current speed Time Training time Training data Basic data setting In the setting mode select „Workout“ point from the menu „Profiles“ „Reset“.
6.3.3 Training A-GPS The watch has a function called “A-GPS” (Assisted global Positioning System). A-GPS is a method, which fastens the search for a good GPS-reception under bad weather conditions. The A-GPS data will be saved on a server and transferred to the watch via the Runtastic Connect. The validity period of this data is 7 days. In order to use this function you require internet access. Download the A-GPS data Connect the watch with the USB cable and then plug in the cable to your computer.
Then the GPS watch does not know what satellite constellation it should wait and has to gather the data again. Then there is warm start, in the best case it takes approximately 10 seconds. A warm start can function only when the GPS watch did not go a long distance away from the last determination of the position and there was not too much time since then.
When this symbol appears, enough satellites were found in order for the GPS watch to determine a 3D position (with altitude). If the satellites are lost and no position is determined, "GPS Lost" appears on the screen, until a button is pressed. GPS manual stop In order to stop the search for satellites, the following options exist: 1) In the setting mode select „GPS” point from the menu „On/Off“, set 2) „GPS Off!“ Press and hold down the "VIEW" from the GPS-Workout-mode.
Recording of lap times During the training, press the "LAP/RESET” button to record the time of a lap. For each workout, the maximum number of lap times is 99. Automatic recording of lap times „Lap-By-Distance” By this function, laps can be automatically generated. Then the "LAP/RESET” button no longer needs to be pressed to record the time of a lap. In the setting mode select „Workout” point from the menu „SmartLap“ „By Dist“. Set the desired distance, after which a lap will always be marked (e.g.
Then press "On", to activate „Lap-To-Waypoint” function. Then select one of the paths. This path will be erased and replaced with a new reference point Setting of measurement interval The GPS watch records the path continuously. You can set manually how often the measurements are performed, from 1 second up to 10 minutes. The basic setting is 4 seconds: In the setting mode select „Workout” point „Tracklog“. Then adjust the interval desired for measurements 6.3.
(Part 1) First row: Number of recording (Training) Press the „ST./STP.“- or the „LAP/RESET” buttons, to switch between recordings (trainings) Second row: Date Third row: Time Fourth row: Integral number of the laps from this recording (2nd Part) Training time Distance Average pace (time per km) (3rd Part) Calories Average cardiac frequency Average speed Press the „VIEW“-button, to view the History of laps.
6.4 GPS-Navigation-mode Press the „MODE“-button multiple times until you get to the “GPS Navigation-mode”, as you can see on the display. Current Speed Distance to the activated checkpoint Directional arrow Navigation Data Paths and Waypoints You can save up to 10 routes on this GPS-watch, but you can only work with one path. A path can consist of up to 99 waypoints. Waypoints within a path can be linked with each other and form a path, but they also can be single waypoints.
First choose the path, the navigation-mode and the waypoint-radius, like described as follows: Choose path Choose “Settings” “Navigation” “SelPath” Now you can choose from path 1 to path 10 Delete path Choose “Settings” “Navigation” “DelPath” Now you can choose from path 1 to path 10 Navigation types There are three different types of navigation: Waypoint-navigation: The activated waypoint is the goal. Choose this navigation type, to go to an individual waypoint on the activated path.
Waypoint-radius Here you can adjust when exactly a waypoint is reached. Basic setting is 30 meters (98,43 feet). So when you enter this radius, the waypoint is reached. You can also adjust the radius manually (from 10 to 200 meters/ 32,81 to 656,17 feet). To adjust the waypoint-radius manually, hold the “MODE”-button to get to the menu, choose “Navigation” “WP Radius”.
To start the search for satellites, there are following options: 1) Hold the “MODE”-button to get to the menu, choose GPS “On/Off”, and activate “on”. 2) Press and hold the “VIEW”-button in the GPS-navigation-mode. Once you received the GPS-signal, the display shows a directional arrow, which will show you the way to the next waypoint.
heart rate measurement are activated automatically (if this has not been done yet manually). Recording Lap Times During the workout press the “LAP/RESET”-button to record a lap time. The maximum number of lap times for each workout is 99. Current Speed Directional arrow Distance to the activated waypoint Navigation Data The current speed and the distance to the activated waypoint are displayed.
6.4.2 Go-to-display Enter the GPS-Navigation mode and press the “VIEW”-button several times, until you see the following display: Waypoint number Path name Navigation data You can choose a waypoint from the previous path by either pressing the “ST./STP.” or the “LAP/RESET”-button.
Direction 6.5.
watch parallel to the floor and rotate clockwise, until "Done" appears on the screen. 6.5.2 Entry of declination The GPS watch, as most of the magnetic compasses, shows toward the magnetic North Pole. Any departure on a map however refers to the geographical North Pole. An angle arises from here. This is called deviation or declination. Geographical North Pole Magnetic North Pole Magnetic declination Magnetic declination To correct this declination, the deviation degree can be introduced.
degrees). Also, the internet page www.magnetic-declination.com is useful, to find the declination of a place. To enter the declination, in the adjustment mode select “Settings” “System” “Compass” “Declinate” 7 Then adjust the declination. Economic functioning The GPS watch has an economic functioning mode. Thus, the light turns off, in order to extend the economic life of the accumulators. To activate the economic functioning, in Time mode press the “LAP/RESET” button for approx. 5 seconds.
approximately 5 seconds. Press the "LIGHT" button shortly to exit the night mode. Display brightness disappears after approximately 5 seconds. However, note that more power is consumed for display brightness; therefore the accumulator will be discharged faster. 9 9.1 Charging the accumulator, replacement of batteries respectively Charging the accumulator of the GPS watch The GPS watch has a lithium-polymer accumulator.
To charge the accumulator, proceed as follows: Fix the clip of USB cable on the GPS watch according to the following image and insert the USB cable in a USB connected to power from your computer. The installation of a driver for charging the accumulator is not necessary. During the charging process the following symbol appears on the screen: The charging of an empty accumulator takes approximately 2 hours. When the accumulator is fully charged, the display "battery full" appears. 9.
so that moisture does not infiltrate in the chest strap 10 Data download Runtastic Connect is a software to upload the training data from the watch to your Runtastic profile, where you can then analyse the data.. 10.1 Download the installation files You can download the installation file for the program and the drivers for the USB cable from following homepage: http://www.runtastic.com/connect 10.2 1. 2. 3. 10.3 How to install Runtastic Connect Do not yet connect the USB cable with your computer.
10.4 Using Runtastic Connect See below the most important facts how you can use Runtastic Connect: 1. Connect the watch with the USB cable and then plug in the cable to your computer. Runtastic Connect will open automatically once linked to the watch with following window: Click to this arrow to open up the window completely: To sign up with your Runtastic account, click on “Connect account”. Automatically you will be linked to the homepage of Runtastic were you can log in with your Username.
You can switch between the following windows: “User” “Customize” 56
“System” In each window you can make adjustments in the settings which will be transferred to the watch once you press the “Save” button. 11 Technical data GPS watch Power supply: GPS accuracy: Lithium-polymer accumulator, 380 mAH, 3,7V 3 meters CEP (50%) under clear sky conditions The indication of the accuracy is based on the so-called CEP 50% (Circular Error Probability).
Accuracy of position determination Chest strap Power supply: 1 Lithium battery (3V, CR2032) Transmission frequency from the chest strap to the GPS watch: 2,4 GHz 12 Declaration of compliance R&TTE Directive 1999/5/EG: Shortened text of the declaration of compliance: By this, Krippl-Watches, declares that the GPS watch (Art.-No. RUNGPS1, Type: D02I280), as well as the chest strap (Art.-No. RUNGPS1, Type: T00018D) comply with the applicable basic conditions and dispositions of 1999/5/EG directive.
13 IC Statement (For Canada) - This equipment is portable device. The output power of this device is less than 20mW. The SAR test is not required. - This device complies with Industry Canada licence - exempt RSS standard(s). Operation is subjectto the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
14 FAQ/Correction of errors Before claiming the GPS watch, verify if the accumulators are charged and charge them if need be. Also, check the batteries from the chest strap and replace them if need be. I’d like to start training, why doesn’t the GPS watch show speed? It is important for GPS fast reception that the watch be at rest and not to be on the move. Before starting running, before starting the path respectively, start your GPS watch, in open space, with clear view to the sky (e.g.
How long does the accumulator of the GPS watch last? The service life of the accumulator is of 14 hours, when using the GPS, and of approx. 1 year in time mode. It doesn’t show my current speed, why? Check if you receive enough GPS signal. Why does the GPS watch show a certain speed, if I do not walk/I am not on the move? This depends on the exactness of position determination, measurement intervals of the GPS respectively. See next paragraph, the exactness of the GPS watch respectively.
Why when riding the bike, a different speed in comparison to the computer without bike cable is shown? Do not use the computer without bike cable and the GPS watch simultaneously. The signals of the sensor from the bike computer may disturb the GPS watch. Thus, false displays can be shown. Can the cell phone and the GPS watch be mounted together on the handle bar of the bike? It is not recommended because disturbances (radio) may appear.
15 Warranty We provide a 24 months warranty for this product. The warranty period begins on the date of purchase (till receipt, purchase voucher). During this period you will receive free of charge a new or repaired product. The warranty does not include batteries, improper handling, dropping, shock or the like. In case of a claim you have the following possibilities: a) contact your point of sale or b) write us an e-mail: service@runtastic.
Runtastic.
