Model :RFBW12304 Model :RFBE 12304 Model :RFBG 12304 Wall Cabinet Operators’ Manual Manual de Operadora del Gabinete de pared Inspect product prior to installation. Contact info@runfinegroups.com prior to returning product to retailer. Inspeccione el producto antes de su instalación. Póngase en contacto con info@runfinegroups.com antes de devolver el producto al vendedor.
PARTS LIST A. LEFT SIDE PANEL / PANEL LATERAL IZQUIERDA B. RIGHT SIDE PANEL / PANEL LATERAL DERECHO C. TOP PANEL / PANEL SUPERIOR D. BOTTOM PANEL / PANEL INDERIOR E. BACK DOWN CROSS BAR / BARRA TRANSCERSAL INFERIOR POSTERIOR F. BACK TOP CROSS BAR / BARRA TRANSCERSAL SUPERIOR POSTERIOR G. ADJUSTABLE SHELF PANEL / PANEL DEL ESTANTE AJUSTABLE H. UPPER BACK PANEL / PANEL SUPERIOR POSTERIOR I. LOWER BACK PANEL / PANEL INFERIOR POSTERIOR J1. LEFT DOOR PANEL / PANEL IZQUIERDA PUERTA J2.
HARDWARE 1. DOOR KNOB / PERILLA DE LA PUERTA 2. DOOR KNOB SCREW (18MM L) / TORNILLO PARA LA PUERTA PERILLA (18MM L) 3. CAM LOCK NUT & BOLT / TUERCA & PERNO CAM 4. WOOD DOWEL / TACO DE MADERA 5. SHELF SUPPORTS / SOPORTA DE ESTANTE 6. DOOR MAGNET AND SCREW / IMÁN Y TORNILLO DE LA PUERTA BLANCA 7. WOOD SCREW (12MM L) / TORNILLO DE MADERA (12MM L) 8. DOOR HINGES & SCREW / BISAGRAS & TORNILLO 9.
TOOLS REQUIRED (NOT INCLUDED) FLAT HEAD SCREWDRIVER PHILLIPS SCREWDRIVER Por favor, lea las instrucciones antes del montaje. Please read instructions before assembly. Perform assembly on a carpeted surface to prevent scratching. Realizar el montaje sobre una superficie enmoquetada para evitar que se raye. This assembly process require at least two people. Este proceso de montaje requiere al menos dos personas.
ASSEMBLY OF THE SIDE PANELS,BACK TOP CROSS BAR, BACK DOWN CROSS BAR, BOTTOM PANEL & TOWEL BAR（STEP 1)- #B ASAMBLEA DE LOS PANELES LATERALES, BARRA TRANSCERSAL INFERIOR POSTERIOR, BARRA TRANSCERSAL SUPERIOR POSTERIOR, PANEL INFERIOR Y EL TOALLERO (PASO 1)- #B Attach the side panels (A) &(B) to the back top cross bar (F), the bottom panel (D) and the back down cross bar (E) by inserting camlock bolts(3) and wood dowels (4), Insert towel bar (K) into the pre-drilled hole of left & right side panel (A,B) as sho
ASSEMBLY OF THE TOP PANEL（STEP 2) ASAMBLEA DEL PANEL SUPERIOR (PASO 2) Insert the cam lock bolts (3) into the pre-drilled hole of the top panel (C). Attach the top panel (C) to the side panels (A) & (B) as shown (Figure 4). Inserte los pernos de bloqueo de leva (3) en el agujero previamente taladrado del panel superior (C). Fije el panel superior (C) a los paneles laterales (A) y (B) como se muestra (Figura 4). Figure 4 Insert the camlock nut (3) into the pre-drilled hole of the side panels (A) & (B).
ASSEMBLY OF THE BACK PANEL（STEP 3) ASAMBLEA DEL PANEL POSTERIOR (PASO 3) Attached the back panel (H)& (I) to the cabinet using the wood screws (7) as shown (Figure 6). Se adjunta el panel trasero (H) (I) al gabinete con los tornillos de madera (7) como se muestra (Figura 6). Figure 6 ASSEMBLY OF THE DOOR PANEL & DOOR KNOB（STEP 4) ASAMBLEA DE LA PUERTA DEL PANEL DE PUERTA Y MANDO (PASO 4) Screw the door hinges (8) to the door panel(J) using the hinge screw (8).
WALL MOUNT INSTALLATION（STEP 5) INSTALACIÓN MONTAJE EN PARED (STEP 5) Locate a desired position on the wall on which to mount the cabinet. If wall studs are located at the exact screw positions of the cabinet cross bars, then mount the cabinet to the wall using mounting screws (9). If the wall behind the cross bars is hollow, then drill through all mounting holes to mark hole positions on the wall. Remove the cabinet from the wall.
