I NSTALLATION/ O PERATION M ANUAL CX-70DHD 1080p, High-Definition Flat Panel LCD and Digital High Definition (DHD) Controller with
RuncoCare™ Standard Two Year Limited Warranty Congratulations on your purchase of a Runco® product! With proper installation, setup and care, you should enjoy many years of unparalleled video performance. This RuncoCare Standard Limited Warranty is provided free of charge by Runco International with the purchase of a covered Runco product.
RuncoCare Claim Procedure In the event of a product defect, please follow the warranty claim procedure provided below: 1. The Customer is required to contact a Runco dealer or Runco Technical Support via email at support@runco.com or via phone at (toll free) 800-23RUNCO (800-237-8626). If the customer is located outside North America, call +3589 4200 554 in Europe for product service. 2.
j Failure to follow maintenance procedures as outlined in the product’s user guide where a schedule is specified for regular cleaning of the product k Opening the product and/or tampering with internal circuitry l Products lost, stolen or discarded m Any damage or dissatisfaction associated with latent images, “burnin,” or any other damage determined by Runco to be the result of customer use patterns n Any other cause, which does not relate to a product defect in material or workmanship 5.
Exclusion of Damages RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. 1. RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Important Safety Instructions Thank you for your purchase of this quality Runco video product! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions.
Compliance Information DECLARATION OF CONFORMITY: Manufacturer’s Name: Runco International, LLC Manufacturer’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992 hereby declares that the Products’ Model Numbers: EL IM IN A R conform with the provisions of: Y CX-70DHD Council Directive 2004/108/EC on Electromagnetic Compatibility; EN 55022 “Limits and methods of measurements of radio interference characteristics of information technology equipment” 1998; EN 55024 “Limits and methods of measuremen
FCC PART 15: NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. INDUSTRY CANADA (ICES-003): EL IM IN A R This Class A digital apparatus complies with Canadian ICES-003.
PR EL IM IN A R Y Notes: x CX-70DHD Installation/Operation Manual
1 Table of Contents RuncoCare™ Standard Two Year Limited Warranty ................................................... iii Important Safety Instructions ....................................................................................... vii Compliance Information .............................................................................................. viii 1. Introduction ...............................................................................................................
Connections to the CX-70DHD and DHD Controller ...................................................21 Connecting the CX-70DHD to the DHD Controller ................................................21 Connecting Source Components to the DHD Controller .......................................23 RS-232 Controller Connection ..............................................................................28 Connecting 12-Volt Trigger Outputs to External Equipment ..................................
1 List of Figures 2-1. CX-70DHD Controls and Indicators ..............................................................................5 2-2. CX-70DHD Connector Locations..................................................................................6 2-3. DHD Controller Front Panel ..........................................................................................7 2-4. DHD Controller Rear Panel ...........................................................................................9 Y 2-5.
List of Figures PR EL IM IN A R Y Notes: xiv CX-70DHD Installation/Operation Manual
1. Introduction This Owner’s Manual describes how to install, set up and operate a Runco CX-70DHD Flat-Panel LCD and DHD Controller. 1.1 About This Manual Y Throughout this manual, the Runco CX-70DHD Flat-Panel LCD and DHD Controller are referred to collectively as the “CX-70DHD.” EL IM IN A R Runco has prepared this manual to help installers and end users get the most out of the CX-70DHD.
Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: Note NOTES emphasize text with unusual importance or special significance. They also provide supplemental information. Caution CAUTIONS alert users that a given action or omitted action can degrade performance or cause a malfunction.
Introduction Following the longstanding tradition of providing the finest custom theater products, Runco proudly unveils its 70-inch Crystal Series™ LCD, the CX-70DHD. Runco’s largest LCD flat panel joins the esteemed Crystal Series, which represents the finest Runco has to offer and is a testament to Runco’s commitment to deliver the most exquisite flat-panel displays for an unsurpassed large-screen experience.
Introduction Parts List ➤ Your CX-70DHD is shipped with the following items. If any items are missing or damaged, please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.
2. Controls and Functions 2.1 CX-70DHD at a Glance Controls and Indicators PR EL IM IN A R Y Figure 2-1 shows the CX-70DHD controls and indicators. 1 IN OUT RS-232 IN ANALOG IN DVI OUT 4 3 2 Figure 2-1.
Controls and Functions 1. DISPLAY STAND Included with the CX-70DHD for table-top installations. 2. POWER SWITCH Connects or disconnects the display panel from the AC power source. 3. STANDBY/ON INDICATOR - Lights blue to indicate normal operation; - Lights red to indicate that the CX-70DHD is in standby mode. 4. REMOTE CONTROL SENSOR Receives the signals from the remote control. Y Figure 2-2 shows the connector locations on the CX-70DHD, and the paragraphs that follow describe them.
Controls and Functions 1. RS-232 IN Connect the RS-232 OUT port on the DHD Controller to this input. 2. RS-232 OUT Not used. 3. ANALOG IN Not used. 4. DVI IN Connect the HDMI output from the DHD Controller to this input. 5. DVI OUT Not used. EL IM IN A R Y 6. POWER INPUT Connect the CX-70DHD to AC power here. 2.2 DHD Controller Front Panel 1 PR Figure 2-3 shows the controls and indicators on the DHD Controller front panel; the paragraphs that follow describe them. 2 3 4 5 6 7 Figure 2-3.
Controls and Functions 5. UP BUTTON Used to direct select aspect ratios or move the menu cursor up in the OSD. When no menu is present on-screen, the UP button toggles through aspect ratios in the following order: 16:9 - 4:3 - Letterbox - VirtualWide - Cinema 6. LEFT BUTTON Used to direct select inputs or move the menu cursor left in the On-Screen Display.
Controls and Functions 2.3 DHD Controller Rear Panel Figure 2-4 shows the rear connector panel on the DHD Controller. 8 4 9 SYSTEM CONTROL INTERFACE CAUTION INPUTS Serial No R/Pr G/Y B/Pb RISK OF ELECTRIC SHOCK DO NO T OPEN H V ! AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR TRIGGERS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE CENTER.
Controls and Functions 8. 12-VOLT (750 mA) TRIGGER OUTPUTS Connection for up to three (3), 12-volt trigger-controlled devices such as retractable screens or screen masks. 9. IR Wired input from a wired remote control or infrared receiver. It is a 3.5-mm, mini phono jack, wired as follows: Ring = +5V Tip = IR Input Sleeve = Ground When an external remote control or infrared receiver is connected to the wired IR input, the IR sensor on the front of the DHD Controller is disabled. Y Note EL IM IN A R 10.
Controls and Functions Figure 2-5 shows the DHD Controller remote control, and the paragraphs that follow describe its functionality. 2 Y 1 4 (not available on some models) 5 RETURN EXIT 6 8 EL IM IN A R 3 7 9 16 : 9 11 4:3 12 10 14 HDMI 1 HDMI 2 PR 13 CUST 1 CUST 2 SVC Figure 2-5. DHD Controller Remote Control CX-70DHD Installation/Operation Manual 11 2.
Controls and Functions 1. IR OUTPUT INDICATOR Lights when a button is pressed to indicate that an IR signal is being transmitted. 2. ON / OFF Press to turn the CX-70DHD on or off. 3. ENTER Press to select a highlighted menu item or confirm a changed setting. 4. Cursor Keys ( , , , ) Use these buttons to select items or settings, adjust settings or switch display patterns.
Controls and Functions 10. Aspect Ratio Selection Buttons Use the red buttons to select an aspect ratio directly or to enter numeric characters, as follows: 16 : 9 (3) For viewing 16:9 DVDs or HDTV programs in their native aspect ratio. 4 : 3 (6) Scales the input signal to fit 4:3 display mode in the center of the screen. Y LETBOX (Letterbox) (9) For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.
Controls and Functions PR EL IM IN A R Y Notes: 14 CX-70DHD Installation/Operation Manual
3. Installation 3.1 Remote Control To install batteries in the remote control: EL IM IN A R Y 1. Press down the tab on the cover and pull the cover in the direction of the arrow. 2. Insert the included batteries. Ensure that the polarities correctly match the and markings inside the battery compartment. 3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place. • When installing batteries, make sure that the battery polarities are correct.
Installation • Do not drop the remote control or expose it to moisture or high temperature. • The remote control may malfunction under a fluorescent lamp. If that occurs, move the plasma display away from the fluorescent lamp. • Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the plasma display. Note The signal from the remote control can be reflected by walls or other surfaces.
Installation Table 3-1 gives a quick overview of the CX-70DHD installation process. The sections following this one provide detailed instructions. Note Installation should be performed by a qualified custom video installation specialist. For Details, refer to page... Procedure EL IM IN A R Step Y Table 3-1.
Installation 3.3 Installation Considerations Proper installation of your CX-70DHD will ensure the highest possible picture quality. Whether you are installing the CX-70DHD temporarily or permanently, you should take the following into account to ensure that it performs optimally. In general, minimize or eliminate light sources directed at the display.
Installation Here are some other considerations and tips that can help improve your installation, avoid damage and prolong operating life: Other Considerations • Keep the ambient temperature constant and below 35°C (95°F). Keep the display away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the display circuitry, which may affect performance. • Keep the CX-70DHD away from devices that radiate electromagnetic energy such as motors and transformers.
Installation Table Stand Assembly: Figure 3-3 shows how to assemble the included table stand and attach it to the panel. Description 1 2 2 6 Table stand upright 1/4-20 x 1.5" Low head socket cap screw 3 2 Table stand foot 4 5 8 8 M8 x 40mm, Socket head cap screw Rubber Bumper EL IM IN A R Y Item Qty PR 1 3 2 5 4 Figure 3-3.
Installation If you choose to wall-mount the CX-70DHD, ensure that the wall-mount bracket is installed according to the instructions included with it. The wall must be capable of supporting a redundant weight factor five (5) times the weight of the display, or be reinforced. Runco recommends that this be done by a custom installation specialist. Use only a Runco-approved wall-mount kit or table stand that is specifically designed for your display. Refer to Parts List on page 4 for ordering information.
Installation IN OUT RS-232 IN ANALOG IN IN OUT RS-232 IN ANALOG IN Y OUT EL IM IN A R OUT R/Pr PR DVI DVI SYSTEM CONTROL INTERFACE G/Y B/Pb H V ! AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR TRIGGERS HD1 1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN INPUTS Serial No 2 IR 3 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE CENTER.
Installation RS-232 Connection: Connect the RS-232 output from the DHD Controller to the RS-232 IN input on the CX-70DHD. Use a cable with an RJ11 plug at the DHD Controller end and an RJ-45 plug at the CX-70DHD end. (The CX-70DHD accessory kit includes such a cable.) If you make your own cable, it must be wired as shown in Figure 3-5.
Installation INPUTS R/Pr G/Y B/Pb H V TRIGGERS HD1 1 2 3 IR HD2 R/Pr G/Y B/Pb H V Pb HDMI 2 Y Component Video S-Video 1 Video S-Video 2 EL IM IN A R Y HDMI 1 Pr HDMI Source (HD-DVD/BD/DVD Player or HD Tuner with HDMI or DVI out) PR Figure 3-6.
Installation Digital (DTV) RGB or Component Video Connections: See Figure 3-7. R/Pr G/Y INPUTS B/Pb H V TRIGGERS HD1 1 2 3 HD2 R/Pr G/Y B/Pb H V S-Video 1 Pb HDMI 2 Pr Y Component Video Video S-Video 2 DTV or Progressive Component (YPbPr) Source Horiz Vert PR Red/Pr Green/Y Blue/Pb EL IM IN A R Y HDMI 1 Figure 3-7.
Installation Analog (Computer) RGB Connections: See Figure 3-8. 1. Refer to Supported Timings on page 60 for a list of computer signals compatible with the CX-70DHD. Use with signals other than those listed may cause some functions not to work. Note 2. Some Macintosh computers may require a Macintosh video adapter. Contact your nearest authorized service center or dealer.
Installation Composite/S-Video/Component Video Connections: See Figure 3-9. R/Pr G/Y INPUTS B/Pb H V TRIGGERS HD1 1 2 3 HD2 R/Pr G/Y B/Pb H V S-Video 1 HDMI 2 Pb Y Pr Component Video Video S-Video 2 EL IM IN A R Y HDMI 1 Pr Y PR Pb DVD Player, VCR, Satellite Receiver, Laser Disc etc. Figure 3-9.
Installation RS-232 Controller ➤ Connection Use a standard, 9-pin RS-232 cable to connect a PC or control/automation system (if present) to the RS-232 Control port on the DHD Controller; see Figure 3-10. For more information about using this connection, refer to Serial Communications on page 51.
Installation If infrared signals from the remote control cannot reach the DHD Controller due to excessive distance or obstructions such as walls or cabinet doors, you can connect an external IR receiver to the DHD Controller to extend the range of the remote control. See Figure 3-12.
Installation PR EL IM IN A R Y Notes: 30 CX-70DHD Installation/Operation Manual
4. Operation 1. Turn on your source components. 2. Press the main power switch on the CX-70DHD (see Figure 2-1). The standby/on indicator lights red. 4.1 Turning on the Power 3. Set the main power switch at the rear of the DHD Controller (see Figure 2-4) to the “on” position. EL IM IN A R Y 4. Press the ON button on the remote control to turn on the DHD Controller and CX-70DHD (or press the power button on the front of the DHD Controller). The power indicator on the DHD Controller lights solid blue. 5.
Operation 2. Double click on the Display icon. 3. Click the Settings tab on the display dialog box. EL IM IN A R Y 4. Set the Screen area to 1024x768 pixels. PR 5. Click the Advanced button and click the Monitor tab on the dialog box. Set the Refresh Frequency to 60Hz and click OK. Note 1. The native resolution of the CX-70DHD is 1920 x 1080. Other horizontal or vertical resolutions may be scaled upward or downward to fit the display. 2.
Operation Press the MENU button on either the remote control or the DHD Controller front panel to display the Main Menu. To select a menu item, use the UP ( ) and DOWN ( ) buttons on either the remote control or the DHD Controller front panel to highlight it. Press ENTER to confirm your selection. The CX-70DHD OSD menus are arranged hierarchically, as shown in Figure 4-1. Depending on the selected input source and signal characteristics, some menu options may not be available.
Operation Picture Input Position Memory Presets Information (read-only) PR Test Video ISF Night - Input Image ISF Night - Input Color ISF Day - Display Color Y Aspect Ratio ISF Night - Display Color ISF Day - Input Image Calibration (1080i analog and lower-resolution sources) EL IM IN A R Input Source Composite S Video 1 S Video 2 Component SD HD/RGB 1 HD/RGB 2 HDMI 1 HDMI 2 16:9 4:3 Letterbox VirtualWide Cinema Brightness Contrast Color Tint Sharpness Left/Right Up/Down Width Height Overs
Operation The Main Menu is the starting point for accessing all display functions. Main Menu (The Calibration and Service menus are hidden and not accessible until you enter a passcode.) Runco Video Input Source Aspect Ratio Picture Input Position Memory Presets Information Calibration EL IM IN A R From the Main Menu, select Input Source to choose a video signal source. Y Service The active source is indicated by an arrow (>) to its left; in this example, Composite is the active source.
Operation Table 4-1. Aspect Ratio Settings Aspect Ratio Remote Control Key 16:9 16:9 Description Select 16:9 to view 16:9 DVDs and HDTV programs in their native aspect ratio. EL IM IN A R Y 16:9 Image on 16:9 Screen (Display) 4:3 images are stretched horizontally to fit a 16:9 screen.
Operation Use the controls in the Picture Menu to calibrate the analog inputs on the CX-70DHD for optimum picture quality. Picture Picture Note To calibrate the digital (HDMI 1 and HDMI 2) inputs, use the Display Image controls in the Service menu. For more information, refer to Display Device on page 46. Brightness Contrast Color Tint EL IM IN A R Y The CX-70DHD has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF).
Operation PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes. Select Brightness from the Picture menu and press ENTER. Adjust the brightness so that: • The darkest black bars disappear into the background. • The dark gray areas are barely visible. • The lighter gray areas are clearly visible. • The white areas are a comfortable level of true white.
Operation EL IM IN A R Y blue red magenta green cyan yellow gray Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in Figure 4-4. Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint blue red magenta green cyan PR yellow gray Select Color and press ENTER.
Operation EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5. Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. Figure 4-5.
Operation Overscan: Image Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area. Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Over scan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area. Select from 1% to 10% of Overscan, as desired.
Operation Calibration ➤ Use the Calibration menu to perform advanced picture quality adjustments on the analog inputs. This menu should be used by ISF-certified technicians only. Calibration ISF Night Note Display Color Input Image Input Color Note ISF Day To calibrate the digital (HDMI 1 and HDMI 2) inputs, use the Display Image controls in the Service menu. For more information, refer to Display Device on page 46. You must enter a passcode to access the Calibration menu.
Operation Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image. ISF Day - Display Color: Refer to ISF Night - Display Color. ISF Day - Input Image: Refer to ISF Night - Input Image. ISF Day - Input Color: Refer to ISF Night - Input Color. Y Save ISF Settings: Whenever you make a change to the ISF settings, you should always save it.
Operation Service ➤ Use the Service menu to access advanced display configuration settings. This menu should be used by ISF-certified technicians only. Service Test Video Note Input Names You must enter a passcode to access the Service menu. Remote Control Analog Out Mode HD Format Triggers Miscellaneous Press MENU to exit test pattern mode.
Operation Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the DHD Controller will respond. By default, both are set to 17. You can change these codes if either: • Another device in the theater (a DVD player, for example) is responding to commands from the DHD Controller remote control (Figure 2-5) in ways that are unpredictable or undesirable. Note Use the DHD Controller front-panel keypad to change its IR code.
Operation Display Device: The options in the Display Device menu allow you to perform the following LCD image adjustments. • Display Position: Select Display Position from the Display Device menu to perform the following display device adjustments (these are global, independent of any input): • Select Hpos or Vpos and use the position. or buttons to fine-tune the displayed image • Select H.Size.L or H.Size.R and use the image width (horizontal zoom). • Select V.Size.T or V.Size.
Operation • HD/RGB 1 and HD/RGB 2 (Color Space): Select Auto, RGB or YUV. • ADC Bandwidth: Select Auto, 75 MHz, 150 MHz or 300 MHz. • YPbPr Input Resolution: Select Auto or specify the input resolution, if known: 480i, 480p, 576i, 576p, 720p or 1080i. Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.
Operation PR EL IM IN A R Y Notes: 48 CX-70DHD Installation/Operation Manual
5. Maintenance and Troubleshooting Regular cleaning will extend the life and performance of the CX-70DHD. Before cleaning, be sure to unplug the power cord from the power outlet. Do not under any circumstances use solvents such as benzene or thinner to clean the CX-70DHD. Doing so may cause deterioration or peeling of paint from the display or remote control unit. 5.1 Cleaning Cleaning the Display Panel Body and Remote Control EL IM IN A R Y Wipe the display and remote control gently with a soft cloth.
Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) • Faulty or incorrect video connection between the DHD Controller and the CX-70DHD. • Ensure that the HDMI output from the DHD Controller is properly connected to the DVI IN input on the CX-70DHD (see Figure 3-4). The display is on and menus appear, but there is no picture. • Incorrect source selection. • Source component is not turned on. • Source component is connected incorrectly or not at all.
6. Serial Communications To interface the CX-70DHD with an automation/control system or a PC running terminal emulation software, connect it to the RS-232 output of the DHD Controller as shown in Figure 3-5. Connect your control system or PC to the RS-232 input of the DHD Controller as shown in Figure 3-10. 6.1 RS-232 Connection and Port Configuration EL IM IN A R Y Configure the RS-232 controller or PC serial port as follows: no parity, eight (8) data bits, one (1) stop bit and no flow control.
Serial Communications Table 6-1 lists the RS-232 command set. The “Parameter (min/max)” column shows the valid parameter ranges, or “NA” for commands that take no parameters. When you enter a valid command, the DHD Controller executes it and acknowledges it with a plus sign on the command line (+ >). When you enter an invalid command – one that is misspelled or followed by values outside the valid range for that command – the DHD Controller ignores it and returns a minus sign (- >). Table 6-1.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications Table 6-1. Serial Commands (continued) Parameter (min/max) Command Value Stored? Description The following serial commands are meant to emulate buttons on the remote control or DHD Controller front panel. Each button has its own serial command, so effectively it is as if you were using the IR remote only you’ll be doing so via serial commands. These commands provide active OSD responses just like the IR remote.
7. Specifications 7.1 CX-70DHD Specifications Table 7-1 lists the CX-70DHD specifications. 1920 x 1080 Screen Size (Active Area): 61.00 in. W x 34.31 in. H (1549.4 x 871.6 mm) 70 in. (1778.0 mm) diagonal Screen Aspect Ratio: 16:9 Available Aspect Ratios: DTV Compatibility: Response Time: EL IM IN A R Native Resolution: Y Table 7-1.
Specifications 7.2 DHD Controller Specifications Table 7-2 lists the DHD Controller specifications. Table 7-2.
Specifications 7.3 CX-70DHD Dimensions Figure 7-1 shows the CX-70DHD dimensions (all dimensions are in inches). 28.11 66.57 EL IM IN A R 70.36 2.62 1.28 0 4.94 .54 4.18 1.50 6.00 39.82 39.28 31.70 23.83 15.96 8.08 .54 0 2X 3.01 PR 17.00 7.56 0 .54 M8-1.25 x 15mm deep (12 places) 4X 21.40 Y 39.82 1.21 .64 0 4X 45.02 66.04 66.57 Figure 7-1.
Specifications 7.4 Supported Timings Table 7-3 lists the signal types supported by each input on the DHD Controller. Table 7-3. Supported Signal Timings by Input 800x600 1024x768 60.00 31.469 25.175 √ 72.00 37.861 31.500 √ 75.00 37.500 31.500 √ 85.00 43.269 36.000 56.00 35.156 60.00 800x600 1024x768 Video – – – – – – – – – – – √ – – – – 36.000 √ – – – – 37.879 40.000 √ √ – – – 72.00 48.077 50.000 √ √ – – – 75.00 46.875 49.
Specifications Table 7-3. Supported Signal Timings by Input (continued) Format Resolution – PAL-60 – Horizontal Frequency (kHz) 50.00 15.625 59.94/60.00 15.734/15.750 Supported? (√ = Yes, – = No) Pixel Frequency HD/RGB 1 HDMI 1 S-Video 1 (MHz) Component HD/RGB 2 HDMI 2 S-Video 2 √ – √ √ √ 4.430 √ – √ √ √ EL IM IN A R PR CX-70DHD Installation/Operation Manual Video 3.
Specifications PR EL IM IN A R Y Notes: 62 CX-70DHD Installation/Operation Manual
SERIAL NUM BER 020-0925-00 Rev. A August 2008 Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.
