I NSTALLER/ I NTEGRATOR M ANUAL VideoWall™ VW-100HD CineWall™ CW-95HD Full HD, In-Wall Display
Online Product Registration and Warranty To register your Runco product and obtain information about warranty and service offerings, please visit http://www.runco.com/info.html. COPYRIGHT AND TRADEMARKS: © Copyright 2008 Runco International, LLC (“Runco”). This document contains proprietary information protected by copyright, trademark and other intellectual property laws. All rights are reserved.
Important Safety Instructions Thank you for your purchase of this quality Runco video product! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions.
Compliance Information DECLARATION OF CONFORMITY: Manufacturer’s Name: Runco International, LLC Manufacturer’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992 hereby declares that the Products’ Model Numbers: EL IM IN A R conform with the provisions of: Y VideoWall™ VW-100HD and CineWall™ CW-95HD Council Directive 2004/108/EC on Electromagnetic Compatibility; EN 55022 “Limits and methods of measurements of radio interference characteristics of information technology equipment” 1998; EN 55024
And: • EN 61000-3-2 “Electromagnetic compatibility (EMC) Part 3, Section 2: Limits for harmonic current emissions (equipment input current up to and including 16 A per phase)” 2000; • EN 61000-3-3 “Electromagnetic compatibility (EMC) Part 3, Section 3: Limitations of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current up to and including 16 A and not subject to conditional connection” 1995; Council Directive 2006/95/EC and amended by M1 an
PRODUCT DISPOSAL: The Product contains small amounts of tin, lead and/or mercury. Disposal of these materials may be regulated due to environmental considerations. IMPORTANT RECYCLE INSTRUCTIONS Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. Y For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG.
1 Table of Contents Important Safety Instructions ........................................................................................ iii Compliance Information ................................................................................................ iv 1. Introduction ...............................................................................................................1 About This Manual .................................................................................................
Table of Contents Connections to the VideoWall/CineWall ......................................................................26 Connecting Source Components to the VideoWall/CineWall .................................26 RS-232 Controller Connection ..............................................................................28 Connecting to AC Power ......................................................................................29 Installing the Screen ...............................................
Table of Contents Key Commands....................................................................................................58 Operation Commands ..........................................................................................58 String Commands.................................................................................................58 Addresses in Commands ...........................................................................................58 Direct Addressing .................
Table of Contents Notes: x VideoWall™/CineWall™ Installer/Integrator Manual
1 List of Figures 1-1. Chassis Installation Brackets (Model CW-95HD shown)................................................8 3-1. Installing the Top Flange and Bottom Brackets...........................................................22 3-2. HDMI/DVI Source Connections ..................................................................................26 3-3. VGA Connections.......................................................................................................27 Y 3-4.
PR EL IM IN A R Y Notes: xii VideoWall™/CineWall™ Installer/Integrator Manual
1. Introduction 1.1 About This Manual This Owner’s Manual describes how to install, set up and operate a Runco VideoWall/CineWall™ Full HD, In-Wall Display. Y Throughout this manual, the Runco VideoWall/CineWall™ Full HD, In-Wall Display is referred to as the “VideoWall/CineWall.” EL IM IN A R Runco has prepared this manual to help home theater installer/integrators safely install and optimize the performance of the VideoWall/CineWall.
Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: Note NOTES emphasize text with unusual importance or special significance. They also provide supplemental information. Caution CAUTIONS alert users that a given action or omitted action can degrade performance or cause a malfunction.
Introduction Runco, the leading brand in luxury video solutions, proudly announces its new VideoWall™ VW-100HD and CineWall™ CW-95HD in-wall video displays, which offer custom home theater design and installation professionals new levels of installation versatility and convenience while achieving full-HD imagery perfection.
Introduction Key Features and Benefits ➤ The VideoWall/CineWall offers these key features and benefits: • Native Resolution: 1920 x 1080 (VW-100HD; 16:9 Native Aspect Ratio) or 1920 x 817 (CW-95HD; 2.
Introduction This section briefly describes the various VideoWall/CineWall system components. PR EL IM IN A R Y The Chassis Assembly is a sheet metal assembly that contains all of the active components of the VideoWall/CineWall, as shown below. The lower middle section of the chassis assembly contains all of the active components described below. A fold mirror mounted at the rear of the chassis reflects light from the display engine.
Introduction Input Connectors and ➤ LEDs The VideoWall/CineWall interface board provides connections for up to six video sources, as well as an RS-232 serial connection for personal computer (PC) or automation/control system interface. For a list of supported display modes on each input, refer to Supported Timings on page 119. DVI TO ENGINE Option Key ICP AUX RS-232 POWER Y 1. RS-232 A female, RJ-45 connector for interfacing with a PC or automation/control system.
Introduction The VideoWall/CineWall remote control unit, shown below, allows you to perform the following tasks: Remote Control 1. ON Press to turn the VideoWall/CineWall on. 2. Source Select Buttons Use these buttons to select a video source (Analog, Digital DVI, Digital HDMI, Component, S-Video or Composite). HDMI DVI ANALOG CPONENT OFF SVIDEO CPOSITE 4:3 16:9 L BOX V WIDE CINEMA V CINE ON 1 2 EL IM IN A R Y 3 3. OFF Press to turn the VideoWall/CineWall off. 4.
Introduction Screen Assembly ➤ The Screen Assembly comprises all of the components associated with the screen which is attached on the outer side of the installation wall. The Screen Assembly is packaged separately from the Chassis Assembly, to facilitate unpacking and installation. Southco-type latches at the bottom of the screen secure the screen in the closed position. A hinge system is provided at the top of the screen assembly that interfaces to the top flange of the chassis assembly.
Introduction Bottom Brackets: The bottom brackets support all of the weight of the chassis assembly, and provide a pivot point while the chassis is “rotated into” the wall opening. Once installed, these can be screwed into the wall opening with sheet rock screws. Top Flange: The top flange locks the top of the chassis into position and stops the rotation of the chassis as it is being installed.
Introduction PR EL IM IN A R Y Notes: 10 VideoWall™/CineWall™ Installer/Integrator Manual
2. Installation Preparation Y Prior to installing the VideoWall/CineWall, confirm that the installation site meets the requirements described in this section. EL IM IN A R The VideoWall/CineWall is designed for installation into a dedicated, framed, structurally capable wall with at least 32.50 inches (826 mm) of distance between the user-viewable surface of this wall and anything immediately behind the open framed area. The chassis protrudes approximately 30.
Installation Preparation Site Access ➤ The VideoWall/CineWall requires clean, noise-free AC power. The power cord provided with the VideoWall/CineWall is 6 feet (1.83 meters) long. In order to use it, the power outlet must be no more than 48 inches (1.22 meters) from the cable openings on the right side of the chassis. If the outlet is farther away, substitute a longer power cord for the one provided with the VideoWall/CineWall; do not use a power strip or extension cord.
Installation Preparation Also confirm that doorways and elevators (if used) provide sufficient clearances: Minimum Doorway/Elevator Clearances Width min. 2,000 mm min. 900 mm WARNING EL IM IN A R Depth Y Height 900 900 900 900 2,000 2,800 1,700 2,700 2,800 2,000 2,700 1,700 Do not store or transport the VideoWall/CineWall on its side! It should only be placed on its side if absolutely necessary during loading and unloading.
Installation Preparation 2.2 Unpacking and Inspecting When you receive your VideoWall/CineWall shipment, check the shipping containers for damage. If there are signs of damage or rough handling, it is recommended that you have an agent of the carrier present when the equipment is unpacked. If the shipping containers do not appear to be damaged, move them to the installation site before opening them. Y As you unpack each container, check all parts against the shipping documents.
Installation Preparation 4. With the help of your assistant, grasp the chassis by the handles on either side and lift it straight up and out of the shipping container. EL IM IN A R Y Handles 5. Carefully unpack the screen by opening one end of the shipping container and sliding the screen out of the box. 6. Unpack the chassis hardware and verify that you have received all of the parts listed and shown below.
Installation Preparation 2.3 Site Preparation Because every home theater installation is unique, it is impossible to provide detailed, step-by-step instructions that are applicable to every situation. Instead, this manual provides general guidelines for site construction and product installation. Review this information carefully and adapt it as needed to your installation requirements. The instructions in this section describe how to prepare a dedicated home theater for a VideoWall/CineWall installation.
Installation Preparation Create opening in dedicated wall: 1. Locate three studs 48 inches apart. 2. At the center of the middle stud, mark the location of the screen center based on the desired screen height. 3. From this point, measure/mark 44.375 inches to the left and to the right and the appropriate distance above and below (25.25 inches for a VW-100HD; 18.94 inches for a CW-95HD). 4. Using a laser level, determine and mark the locations of the opening corners. Y 5. Double-check your measurements.
Installation Preparation 3. Reinforce the bottom of the wall opening from behind with a 2x6 x 88.75 in. stud. Wall Opening Reinforcement - VideoWall VW-100HD 48.000" (1219.2 mm) 8.500" (215.9 mm) 48.000" (1219.2 mm) 94.750" (2406.7 mm) 88.750" (2254.3 mm) 21.000" (533.4 mm) 22.500" (571.5 mm) EL IM IN A R 50.500" (1282.7 mm) Y 11.500" (292.1 mm) Support stud, 2 x 6 x 88.75 in. Reinforcing studs, 2 x 6 x 73 in. (2 per side) Reinforcing stud, 2 x 6 x 21 in. (1 per side) 48.000" (1219.2 mm) 8.
Installation Preparation 4. Reinforce the top of the wall opening from behind with two (2), 2x12 x 94.75 in. studs. Secure them to the outer studs using 1/4x4-in. lag bolts and washers (two per side), or a suitable equivalent. For additional stability, secure the 2x12 studs to each other using suitable hardware. Lag Bolt, 0.25” x 2.00 in. (3x) EL IM IN A R Y Lag Bolt, 0.25” x 4.00 in. and Washers (4 per side) or equivalent hardware PR Reinforcing studs, 2 x 12 x 94.75 in.
Installation Preparation PR EL IM IN A R Y Notes: 20 VideoWall™/CineWall™ Installer/Integrator Manual
3. Installation Table 3-1 gives a quick overview of the VideoWall/CineWall installation process. The sections following this one provide detailed instructions. Y Table 3-1. Installation Overview For Details, Refer to page...
Installation 3.2 Mounting the VideoWall/CineWall Chassis This section provides detailed instructions for installing the VideoWall/CineWall chassis. Install the Top Flange as shown in Figure 3-1. Then, install the Left and Right Bottom Brackets (the ones with the latches on them) at the bottom corners of the chassis, and install the Left Center and Right Center Bottom Brackets in the two intermediate locations. The illustration below shows the Bottom Brackets for a CineWall CW-95HD.
Installation With the help of your assistant(s), lift the Chassis Assembly by the handles. EL IM IN A R Y While tilting the Chassis Assembly downward, carefully move the Chassis Assembly into the wall opening. Allow the bottom brackets to come to rest on the bottom of the wall opening. Then, rotate the chassis into the opening until the top flange makes contact with the top of the opening.
Installation The VideoWall/CineWall includes a special spacing tool to make it easier to level the Top Flange and ensure that it is the correct distance from the Bottom Brackets. Spacing Tool 1. Place the Spacing Tool on either the Left Center or Right Center Bottom Bracket, as shown. Y Hinge Barrel EL IM IN A R 2. Engage the slot at the top of the spacing tool with the hinge barrel on the Top Flange.
Installation EL IM IN A R Y 5. Secure the Left and Right Side Light Blocks to the chassis and the opening frame. 6. Secure the Bottom Center Light Block/Strut Catch to the opening frame, between the two Center Bottom Brackets. PR 7. Install the other Bottom Light Blocks (left, left center, right center, right) as shown below.
Installation 3.3 Connections to the VideoWall/CineWall Proceed as follows to connect the VideoWall/CineWall to your video sources, external controller(s) – if present – and AC power. When connecting your equipment: • Turn off all equipment before making any connections. • Use the correct signal cables for each source. EL IM IN A R Route all cables through the cable openings on the right side of the VideoWall/CineWall chassis. Y • Ensure that the cables are securely connected.
Installation VGA (RGB PC) Connections: Connect your personal computer or other RGB source to the ANALOG input; see Figure 3-3. DIGITAL DVI Y DIGITAL HDMI EL IM IN A R ANALOG INPUT Figure 3-3. VGA Connections Component Video Connections: Connect your progressive component source (DVD player or HD set top box) to the COMPONENT input as shown in Figure 3-4. PR INPUT Pr DVD/DTV STB Pb COMPONENT Y S-VIDEO COMPOSITE Figure 3-4.
Installation Composite/S-Video Connections: Connect your Composite and S-Video sources to the VideoWall/CineWall as shown in Figure 3-5. VCR COMPONENT Camcorder S-VIDEO Y COMPOSITE EL IM IN A R Gaming Console Figure 3-5. Composite and S-Video Connections RS-232 Controller ➤ Connection Connect a PC or home theater control/automation system (if present) to the RS-232 port as shown in Figure 3-6. Use a standard, straight-through Category 5 cable with RJ-45 plugs at each end.
Installation To install the screen: 1. Remove the Spacing Tool (used to install the chassis; see page 24). PR EL IM IN A R Y 2. With the help of your assistant(s), lift the screen and position it in front of the Chassis Assembly.
Installation EL IM IN A R Y 3. Use the hooks to hang the frame on the hinge at the top of the chassis. PR 4. Use the strut at the bottom of the frame to prop the screen in the open position.
Installation 5. Install the safety catches at the top rear corners of the screen. These prevent the screen from separating from the hinge when the screen is opened or closed. b Place the safety catch on the exposed screw shaft where you removed the nut. Safety Catch Remove this nut, install Safety Catch and replace Hinge Wing Y a Remove the nut at one end of the hinge wing on the back of the screen. EL IM IN A R c Secure the catch using the nut that you removed in Step 5a.
Installation The VideoWall/CineWall optical engine was perfectly adjusted when it left the factory. However, vibration in transit may have moved it. Before performing any other image adjustments, proceed as follows to confirm proper image alignment. To align the optical engine: 1. Press MENU on the remote control and enter the Installer Menu passcode. 2. Select Advanced Options from the Main Menu. 3. Select Image Alignment from the Advanced Options menu. EL IM IN A R Y 4.
Installation 3.8 Color Balancing the VideoWall/CineWall What does Color Balance do? Color balancing is the process of ensuring that whites appear truly white and grays appear truly gray, without any trace of color. Displays differ from one another because of very small differences in the color of the light produced by the lamp and by differences in the dyes used to make the color in a DLP™ optical engine.
Installation Note Copy to Clipboard saves all the current settings to a temporary memory. You can then make more adjustments to see if it gets better or worse. Recall from Clipboard restores these saved settings. The Clipboard is only for testing. These values are not saved when AC power is off. While color balancing, change the White value by a lot, not just one step. It’s difficult to see one step in White. A large change will tell you if you are heading in the right direction.
Installation Selecting a Source ➤ 1. Press MENU on the remote. 2. Select Picture and press ENTER. 3. Select Source and press the button. 4. Choose the source you want and press ENTER. 5. Press MENU again to close all menus. You must enter a passcode to access the Memory, Diagnostics and Advanced Options menus. Otherwise, they are hidden. To obtain this passcode, contact Runco Technical Support.
Installation Computer sources vary greatly from computer to computer and even between video outputs on the same video card. Video sources vary more. Use the Input Levels controls to make the VideoWall/CineWall respond correctly to these non-standard sources. Note Input Levels and Color Balance (described on page 34) do not affect each other, but they both affect the final picture.
Installation Main Menu Picture Size & Position Aspect Ratio Picture Memory Source ISF Memories Sync Type Analog Separate H&V Program Information Vertical Frequency 60 Hz Pixel Frequency Node iD: 123 43.36 kHz Y Horizontal Frequency HPer: 1563 66.02 MHz VLines: EL IM IN A R Horizontal Resolution 1066 1280 Vertical Resolution 768 Frequency 1344 Phase 22.
Installation 3. Select Picture from the Main Menu. 4. Select Input Levels from the Picture Menu. 5. Select Auto White Level (Gain) and press ENTER. The VideoWall/CineWall is now adjusted to the white levels of this computer using this video card. If you change computers or video output cards in the computer, you must do this again. EL IM IN A R Y What is a “completely” new source? The VideoWall/CineWall remembers all the values in the last 10 pictures.
Installation Input Levels – HDMI, ➤ Digital, Component, Composite or S-Video Sources The Input Levels menu for HDMI, Digital, Component, Composite and S-Video sources, shown below, is simpler than that for Analog sources, but serves the same basic purpose: maximizing contrast without “crushing” (where lighter areas appear white or darker areas appear black).
Installation EL IM IN A R Y Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in Figure 3-9. Figure 3-9. Typical Gray Bar Pattern for Adjusting Contrast Select Contrast from the Picture menu and press ENTER. Adjust the contrast to a point just below which the white rectangle starts to increase in size. Brightness and Contrast controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.
Installation 2. Select Blue Only from the Input Levels menu and press ENTER. 3. Select Saturation from the Input Levels menu. blue EL IM IN A R Y red magenta green cyan yellow gray 4. Adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue: Hue: Hue or “tint” is essentially the ratio of red to green in the color portion of the image. When Hue is decreased, the image appears redder; when it is increased the image appears greener.
Installation Use the Picture Position controls to center the picture on the screen. (This is NOT the same as optical engine alignment.) Picture Position Use arrow keys to move image Horizontal Position 234 34 Y Vertical Position 1. Press MENU. EL IM IN A R To adjust the image position: 2. Select Size & Position from the Main Menu. 3. Select Picture Position from the Size & Position Menu. 4. Use the four arrow keys move the picture on the screen.
Installation Saving Your Work and ➤ Recalling a Memory Using ISF Memories: Four memory slots are reserved for use by ISF-certified technicians. These are named “Day,” “Night,” “Custom 1” and “Custom 2.” The ISF Memories are functionally similar to the other, numbered memory slots (described below), but provide some additional useful capabilities: • The ISF Memories can be recalled by pressing a single button on the remote control, or via the ISF Memories menu.
Installation 5. Navigate to an unchecked slot number, or to a checked slot if you want to overwrite what’s already saved. Press ENTER. 6. This menu shows all the data that will be saved. You can change the slot name in this menu but you can’t change anything else.
Installation To manually recall a memory slot: 1. Press MENU. 2. Select Memory from the Main Menu. 3. Select Recall from the Memory Menu. 4. Navigate to the slot you want to recall. You can only land on slot numbers that are not empty (have checks). 5. Press ENTER to open the Recall detail menu. If this slot number has exactly the same settings are currently being used, a (Current) message appears on the top line.
Installation Some parameters (values) are associated with a display “mode” – the horizontal and vertical resolution and the vertical frequency of the incoming source picture. (There are other characteristics that define the display “mode,” but those are the primary ones.) Some parameters are associated with a physical input: Analog, Component, Digital DVI, Digital HDMI, S-Video or Composite Video. Some parameters are global; that is, they are not associated with a specific mode or input.
Installation Table 3-2.
4. Maintenance and Troubleshooting 4.1 Cleaning Dirt is everywhere, and unless the VideoWall/CineWall is in a super-clean room, from time to time you will need to clean the screens, mirrors and/or lens. EL IM IN A R Y Cleaning products and how to use them: For mirrors and screens, a foam spray cleaner works well. It is sold under different names in different parts of the world. It is available from many janitor supply companies or building maintenance supply companies.
Maintenance and Troubleshooting Removing dry dust: Often the cleaning problem is just dust, not fingerprints or other oily dirt. If it’s just dust, wiping with a dry cheesecloth or a dry Shop Towel will usually do the job. Or use one of the cleaning products designed specifically for picking up dust. • Pledge Grab-It™, from Johnson • Swiffer™, from Proctor and Gamble. These are synthetic wipes that have a static charge that holds onto dust.
Maintenance and Troubleshooting Change the lamp after 6,000 hours of use, or sooner if you notice a significant decrease in brightness. 1. Open the screen. 4.2 Lamp Replacement Removing the Old Lamp 2. Turn off the AC power switch and remove the power cord. EL IM IN A R Y 3. Loosen the six screws holding the display engine compartment cover in place. Then, remove the cover. PR 4. Loosen the lamp screw to the right rear of the lamp. 5. Disconnect the lamp cable. 6.
Maintenance and Troubleshooting Installing the New Lamp ➤ 1. Re-connect the lamp cable you disconnected in Step 5 above. Make sure it is fully seated. If the lamp cable is not fully seated on the lamp plug, the lamp will WARNING not operate properly. Overheating may occur. 2. Mount the lamp in its place. Note the two pins opposite the lamp screw. These fit into holes in the optical engine. 3. Tighten the screw you loosened in Step 4 above. 4. Replace the display engine compartment cover. Y 5.
Maintenance and Troubleshooting The VideoWall/CineWall provides several features for identifying and resolving product performance issues. If the solutions suggested here fail to resolve your issue or if you encounter an issue not described, please contact Runco Technical Support. The On-Screen code is a sequence of red and amber lights that flash on the screen to indicate what is wrong. These flashing lights are particularly helpful when the lamp won’t turn on.
Maintenance and Troubleshooting Table 4-1 lists the On-Screen codes and describes their meaning. Table 4-1. VideoWall/CineWall On-Screen Codes Each block represents 0.
Maintenance and Troubleshooting The LEDs on the electronics module can give you more detailed information about the current operational state of the VideoWall/CineWall. To see them, open the screen. Status LEDs DIGITAL DVI Fan - System Fan - DMD DIGITAL HDMI Fan - Lamp Ballast Status Engine Status Lamp Saver ANALOG Serial Cmd Serial Data Remote IR Lamp Source Ready Table 4-2 describes the VideoWall/CineWall LED status indications. EL IM IN A R Table 4-2.
Maintenance and Troubleshooting Isolating Faulty Parts ➤ If you suspect that a part may be faulty, replace it with a known-good one if available. This is a very effective way to find a problem. If the problem goes away, the original part was at fault. If the problem persists, you haven’t found the problem yet, but you have learned something: the original part was not the problem. Re-install it and try something else. If the Lamp Won’t Light: Check to make sure the lamp is actually not lit.
5. Serial Communications To interface the VideoWall/CineWall with a home theater automation/control system or a PC running terminal emulation software: 1. Connect it to your control system or PC as shown in Figure 3-6. 5.1 RS-232 Connection and Port Configuration 2. Press MENU on the remote control and enter the Installer Menu passcode. 4. Select Serial Port Settings from the Advanced Options menu. EL IM IN A R 5. Note the Baud Rate setting; change it if desired. Y 3.
Serial Communications 5.3 Types of Commands The VideoWall/CineWall supports two types of commands: key commands and operation commands. Key Commands ➤ Operation Commands ➤ Key commands mimic pressing a button on the remote control. This is only useful if you can see the screen, otherwise you won’t know where the selector is in the menu. Operation commands tell the display exactly what to do, allowing more flexible and direct control of the display.
Serial Communications 5.5 Command Structure All commands start with two letters: OP or op for operations commands (but not Op or oP) KY or ky for key commands (but not Ky or kY) ST or st for string commands (but not St or sT) The next two characters are the address. Y The next section of the command is the operation, the remote key, or the string, the main part of the command telling the display what to do. EL IM IN A R A few commands have a ‘target.
Serial Communications Sample Operation Commands Command Example (Note) Explanation Disable the auto position feature in display 00 op 00 auto.position.disable ? [CR] Is the auto position feature enabled or disabled in display 00? op 00 brightness + [CR] Increment the brightness in all displays with Group ID 0 Y op 00 auto.position.disable = DISABLED [CR] EL IM IN A R op 00 curtain [CR] op 00 center.
Serial Communications 5.6 Using the Operation Commands Table The Operation Commands table starts on page 71. EL IM IN A R op 38 auto.level.status ? [CR] op38auto.level.status? [CR] op 38 1115 ? [CR] op381115? [CR] OP 38 aUto.LEveL.STAtus ? Operations and Operation Numbers Y The commands are listed in alphabetical order by Operation. In a command, you may use either the ascii text of the operation or its Operation Number.
Serial Communications Table 5-1. Command Types Symbol Execute means the command is executed. No character follows the command (or the Target, if it has one) Example Result op 04 lamp.hours.reset [CR] Resets the lamp hours meter for the Lamp in unit 04. Y [none] Meaning Any word or character or phrase that appears between [square brackets] is for information or clarification only. It is not sent to the display or received from it.
Serial Communications Command Sent Response Explanation OP 00 ASCII.RESPONSE=SYMBOLIC The unit received the command and has set the response type to symbolic and replies will be ascii characters op 00 curtain.pattern ? [CR] OP 00 CURTAIN.PATTERN=BLACK The curtain pattern is set to black. op 00 ascii.response = numeric [CR] OP 00 1137=1 The unit received the command and has set the response type to numeric and will reply with the value number EL IM IN A R Y op 00 ascii.
Serial Communications 5.7 Using Key Commands Command Word Key ➤ Commands Key commands always start with ky or KY. There are two kinds of key commands, command word and numeric equivalent commands. Command word key commands simulate pressing a button on the remote. For example, the command: ky 00 menu [CR] simulates pressing the menu button for display 00. All the other named buttons on the remote control can be “pressed” in this manner by using the name on the remote.
Serial Communications Numeric equivalent commands also simulate pressing a remote button. For example, the command: ky 00 r50 [CR] simulates pressing the MENU key on the remote. All the keys have “R” numbers associated with them.
Serial Communications 5.8 Examples of Operation Commands Recalling Memories ➤ Remember: The slot target number used in the command is one less than the memory slot number as seen in the menus. For example, to recall memory slot #40, in commands you’d specify slot.target = 39. Likewise, to recall the first slot, you’d specify slot.target = 0. ( ). Put the memory number Y Recalling Memories Directly: Use slot.recall (minus 1) in the parentheses. EL IM IN A R What is the difference between slot.recall.
Serial Communications This action fails, because there is nothing in slot #5. Nothing happens to the picture on the screen; it does not change. op 17 slot.action (recall) [CR] 1 2 3 4 5 6 7 8 ▲ Sets the memory slot to #6. 2 3 4 EL IM IN A R 1 Y op 17 slot.recall.target = 5 [CR] 5 6 7 8 ▲ This recalls slot #6 because the target was set to #6 in the previous command. op 17 slot.action (recall) [CR] 1 2 3 4 5 6 7 8 ▲ Recalls settings from memory slot #1.
Serial Communications Asking (Get) and Telling ➤ (Set) To ask about a value or condition, use a question mark [ ? ]. No character should follow the question mark. To set a value or condition, use an equal sign [ = ]. A value must follow the equal sign. Command Example (Note) Explanation asks whether the auto lamp feature is on or off for display 00. op 1* auto.lamp = on [CR] turns on the auto lamp feature for each display that has a Group ID of 1 (and any Unit ID). op 0* auto.
Serial Communications Table 5-4. Data-Only Response Examples Command and Respond Examples Explanation would get the Data-Only response 0 You get only the answer and only in numeric form. This is used mainly when a sequence of commands is sent and the data is acted upon by the program. For instance, the program might query each display as to its lamp state, on or off, then send a Lamp On command to just those displays that are off.
Serial Communications PR EL IM IN A R Y Notes: 70 VideoWall™/CineWall™ Installer/Integrator Manual
5.9 Operation Commands All commands are Operation commands which should start with “op”, except those marked with [ST] which are String commands. For String commands, use the form ST -- build.date ?, and substitute the unit ID for the --. There is no target for string commands. 2 ascii.response 1137 3 aspect 1054 4 aspect.status 1092 5 auto.codes 1132 ? EL I Value number dec Notes CR CRLF LF LFCR 0 1 2 3 Determines the End Of Line character used in replies.
auto.lamp 1037 = 8 auto.level 1116 = 9 auto.level.disable 17423 = 1115 auto.level.status 11 auto.phase.disable 17420 12 auto.position.disable 17422 13 auto.resync.disable 17438 14 auto.setup 16899 15 ballast.dim.level 1210 16 ballast.ratio 1215 ? EL I PR VideoWall™/CineWall™ Installer/Integrator Manual Notes 0 1 2 DISABLE ENABLE 0 1 BLACK WHITE 1 2 NOT.
Value If numbers listed first, use numbers only. Data in [square brackets] is for information only. Value number dec inc get Command types allowed (Use only one symbol) set (Target) Target or Target number must be in parentheses. ( Target number ) Row Operation or String [ ST ] Operation or String number Table 5-5. Operation and String Commands for VideoWall/CineWall (continued) Notes ballast.status 1239 ? 0 – 255 Waveform ID 18 ballast.sw.
bytes.sent 1141 RS232 AUX232 0 2 30 center.point 1110 RED GREEN BLUE ALL 0 1 2 3 31 clear.input.memory 32 clipboard.gray.balance 1163 33 clipboard.recall 1161 34 clipboard.save 1162 35 clipboard.white.balance 1164 36 color.temp 1268 37 commands.received 1107 38 contrast 16902 Value number dec inc get ? Value If numbers listed first, use numbers only. Data in [square brackets] is for information only. Notes 0 – 32767 Used only to indicate that bytes have been sent.
39 curtain 1035 [execute] 40 curtain.pattern 1036 = 41 custom.pattern 1237 42 display.power 1094 43 dynamic.black 1350 44 engine.on 1277 45 fan.state 1096 ? IN M EL I PR POWER.SUPPLY LAMP DMD SYSTEM VideoWall™/CineWall™ Installer/Integrator Manual = ? NONE WHITE RED GREEN BLUE BLACK LOGO + – Value number Value If numbers listed first, use numbers only. Data in [square brackets] is for information only.
fault.state 1175 ? 47 frame.lock.enable 1292 48 frame.locked 1275 49 frequency 50 frequency.horizontal 1070 51 frequency.pixel 1069 52 frequency.vertical 53 frequency.vertical.half 1291 54 gain.all 1033 55 gain.blue 16394 56 gain.green 16392 FAN LAMP WAIT.THEN.ON WAIT LAMP.SAVER READY OK DLP STRIKING ENG.FAN WARMING.UP FAN.
inc dec 57 gain.red 16390 = ? + – 58 gamma 1232 = ? 59 gray.balance 1031 60 highbright 1071 61 horizontal.period 1264 62 hue 63 image.cal.action 1339 64 image.cal.corner 1338 65 image.cal.target = FILM VIDEO + – ? IN = ? Notes 0 – 255 A R Y 0 1 2 3 RED GREEN BLUE ALL Value If numbers listed first, use numbers only. Data in [square brackets] is for information only.
inc dec = ? + – 66 index.delay 1218 67 interlaced 1065 68 ir.remote 1095 = 69 justify 1053 = 70 lamp 1063 71 lamp.hours.high 1111 72 lamp.hours.low 1102 73 lamp.hours.reset 1104 74 lamp.minutes 1103 75 lamp.on.minutes 1312 76 lamp.saver 1105 0 – 1800 Index delay in degrees x 10 (750 = 75.
1145 79 lamp.saver.delay.minutes 1144 80 lamp.saver.state 1146 81 native.frequency 1351 82 offset.all 1032 83 offset.blue 0MIN 5MIN 10MIN 15MIN 30MIN 45MIN 1HR 2HR 4HR 6HR 8HR 12HR 24HR IN M VideoWall™/CineWall™ Installer/Integrator Manual Notes 0 1 2 3 4 5 6 7 8 9 10 11 12 Sets Lamp Saver Timeout value. = ? + – 0 – 23 This is DPMS delay = ? + – 0 – 59 This is DPMS delay with fine control. EL I PR 16393 Value number lamp.saver.delay.
offset.green 16391 = ? + – 0 – 127 85 offset.red 16389 = ? + – 0 – 127 86 offset.reset 1177 87 opt.eng.horizontal.resolution 1125 88 opt.eng.vertical.resolution 1126 89 opt.engine.state 1271 90 osd.enable 1360 91 overscan 1184 92 part [ST] 2 Value number dec 84 Notes Default value varies and is set at factory. Not used with digital sources. A R Y inc Value If numbers listed first, use numbers only. Data in [square brackets] is for information only.
phase 95 plug.and.play 96 97 NONE WHITE GRAY RED GREEN BLUE BLACK RED.SCALE GREEN.SCALE BLUE.SCALE GRAY.SCALE COLOR.BARS LOGO GRID CHECK4X4 COLORSCALE UNIFORMITY ALIGNMENT FOCUS CUSTOM X.ON.WHITE CYAN YELLOW MAGENTA IN M EL I PR 16400 = ? 1152 = ? position.horizontal 16398 = ? + – [varies] position.vertical 16399 = ? + – [varies] VideoWall™/CineWall™ Installer/Integrator Manual 81 + – Value number dec ? inc = Value If numbers listed first, use numbers only.
product [ST] 5X4 4X3 15X9 16X9 2.35X1 3 ? 100 replies.sent 1139 0 2 101 reset.balance 1034 102 resolution.horizontal 16401 103 resolution.vertical 16402 104 revision [ST] 105 runtime.hours.high 1113 106 runtime.hours.low 4100 107 runtime.hours.reset 4613 [execute] 108 runtime.
112 serial.port 1305 113 sharpness 16397 114 slot.action 1082 115 slot.current 1150 116 slot.delete 1174 117 slot.full 1114 118 slot.group 1353 0 2 RS232 AUX232 = 0 1 2 3 0 [slot 1] 1 [slot 2] : 39 [slot 40] VideoWall™/CineWall™ Installer/Integrator Manual ? ANALOG DIGITAL [DVI] COMPONENT S.
1357 120 slot.group.delete 1356 DEFAULT NIGHT DAY CUSTOM1 CUSTOM2 TARGET 0 1 2 3 4 255 [execute] 121 slot.group.recall 1355 DEFAULT NIGHT DAY CUSTOM1 CUSTOM2 TARGET 0 1 2 3 4 255 [execute] 122 slot.group.save 1354 DEFAULT NIGHT DAY CUSTOM1 CUSTOM2 TARGET 0 1 2 3 4 255 [execute] 123 slot.group.target 1358 124 slot.name. [ST] 5 125 slot.name.clear 1081 0 1 IN M EL I = ? PR VideoWall™/CineWall™ Installer/Integrator Manual DISABLE ENABLE Notes A R Y slot.group.
1079 128 slot.recall 1173 129 slot.recall.target 1077 130 slot.save 1172 0 [slot 1] 1 [slot 2] : 39 [slot 40] 255 [current target] EL I [execute] PR VideoWall™/CineWall™ Installer/Integrator Manual Value number [one ascii character value] Notes The target is the nth letter of the 24-character string: 0 – 23. The value is the ascii character to send: numbers, letters, punctuation. Not all punctuation is available.
OFFSET.RED GAIN.RED OFFSET.GREEN GAIN.GREEN OFFSET.BLUE GAIN.BLUE BRIGHTNESS CONTRAST SHARPNESS HUE PHASE SATURATION SELECT.SOURCE FREQUENCY VERT.TOTAL POSITION.HORIZONTAL POSITION.VERTICAL RESOLUTION.HORIZONTAL RESOLUTION.VERTICAL ASPECT JUSTIFY OVERSCAN VIEWPORT.WINDOW.BOTTOM 132 slot.setting (continued) 1078 VIEWPORT.WINDOW.LEFT VIEWPORT.WINDOW.RIGHT VIEWPORT.WINDOW.TOP WALL.HEIGHT ZOOM.WINDOW.BOTTOM ZOOM.WINDOW.LEFT ZOOM.WINDOW.RIGHT ZOOM.WINDOW.TOP 133 slot.
1068 135 source.search.status 1133 136 sync.type 1064 137 system.hours.high 1112 138 system.hours.low 4098 139 system.hours.reset 4612 [execute] 140 system.minutes 4099 = 0 [slot 1] 1 [slot 2] : 39 [slot 40] A R Y slot.target Value If numbers listed first, use numbers only. Data in [square brackets] is for information only. 0 1 : 39 0 1 2 3 4 5 6 7 8 ? UNKNOWN SOG COMPOSITE SEPARATE 0 1 2 3 = ? [hours / 10000] = ? [hours mod 10000] IN M EL I PR Notes VIDEO.
141 system.state 1059 142 temperature.c 1153 BOARD DLP 0 5 143 uart.clear 1187 RS232 AUX232 0 2 [execute] 144 uart.errors 1186 RS232 AUX232 0 2 145 uart.overflows 1185 RS232 AUX232 0 2 146 uniformity.correction 1352 147 vertical.lines 1263 148 video.standard 149 viewport.window.bottom 1042 150 viewport.window.height 1100 WAIT READY ON FATAL.
dec viewport.window.left 1039 = ? + – 152 viewport.window.right 1040 = 153 viewport.window.top 1041 154 viewport.window.width 1099 155 white.balance 1285 156 window.reset.size 1091 157 zoom.window.bottom 1047 158 zoom.window.height 1098 159 zoom.window.
get inc dec 1045 = ? + – 161 zoom.window.top 1046 = 162 zoom.window.width 1097 IN ? PR EL I M ? VideoWall™/CineWall™ Installer/Integrator Manual 90 Value If numbers listed first, use numbers only. Data in [square brackets] is for information only. 0 [–100] : 100 [0] : 200 [+100] 0 : 100 : 200 0 [–100] : 100 [0] : 200 [+100] 0 : 100 : 200 A R Y set zoom.window.right (Target) Target or Target number must be in parentheses.
6. Reference • Press the MENU button on the remote control to display the Main Menu. To select a menu item, use the and buttons on the remote control to highlight it. Press ENTER or to confirm your selection. Y • Use the arrow buttons to select menu items or change settings. EL IM IN A R • Press PREV to return to the previous menu. If you are in the Main Menu, pressing PREV turns off the OSD menu. • Press MENU to turn off the OSD menu.
Reference Analog, Digital, HDMI, Component, S-Video or Composite Source NTSC or PAL (read-only) Sync Type (VGA sources only) Separate H & V, Composite or Sync-on-Green Vertical Frequency Horizontal Frequency Pixel Frequency Horizontal Resolution Vertical Resolution Frequency Phase Sharpness (read-only) Size & Position (passcode required) Lamp Ballast Hours Color Balance Miscellaneous Options Fill Screen, Letterbox, 16x9, 4x3, VirtualwIde, Cinema, Virtual Cinema or One to One Top/Left, Center o
Reference The Main Menu is the starting point for accessing all VideoWall/CineWall functions. Main Menu You must enter a passcode to access the Memory, Diagnostics and Advanced Options menus. Otherwise, they are hidden.To obtain this passcode, contact Runco Technical Support.
Reference Picture Menu – Digital or HDMI Sources Picture Source Digital Vertical Frequency 60 Hz Horizontal Frequency 43.36 kHz Horizontal Resolution 1280 Vertical Resolution 768 Sharpness 7 EL IM IN A R Y Input Levels Picture Menu – Component Sources Picture Source Component (YPbPr) Vertical Frequency (frame locked) 60 Hz Horizontal Frequency 43.36 kHz Horizontal Resolution 1280 Vertical Resolution 720 Frequency 1344 Phase 22.
Reference EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 6-2. Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. PR Figure 6-2.
Reference Input Levels (Analog Sources): Refer to Input Levels – Analog RGB Sources on page 37. Input Levels Auto White Level (Gain) Center Point 2 1 4 Black Level (Offset) - All 55 Red 55 Green 55 Blue 55 127 Y White Level (Gain) - All Red 127 127 EL IM IN A R Green Blue 127 Input Levels (HDMI, Digital, Component, Composite or S-Video Sources): Refer to Input Levels – HDMI, Digital, Component, Composite or S-Video Sources on page 40.
Reference Zoom Window Top & Left/Zoom Window Bottom & Right: Zoom enlarges or reduces the picture. It is primarily used to eliminate black edges at the sides of the picture that cannot be removed using the Picture Position controls. To adjust the zoom: 1. Press MENU. 2. Select Size & Position from the Main Menu. 3. Select Zoom Window Top & Left from the Size & Position Menu. or EL IM IN A R Zoom Top & Left Arrows move top and left button Y 4. Use the or button to move the top edge of the picture.
Reference Zoom menu entries: • Image Resolution is the resolution of the source picture. • This Unit is the number of pixels this unit is using of all the incoming pixels. Viewport Window Top & Left/Viewport Window Bottom & Right: The controls in the Viewport menus adjust the number of pixels actually used on the DMD™. Use them to mask the edges of the display area (to eliminate “snow” or edge noise, for example).
Reference 7. Use the or button to change the number of masked (unused) pixels at the bottom edge of the picture. Use the or button to do the same at the right edge of the picture. Viewport Bottom & Right Arrows move bottom and right +0 Y +100 EL IM IN A R -100 +0 Display Resolution Viewport 1920x817 1289x817 Viewport menu entries: • Display Resolution shows the resolution of the DMD chip. This has nothing to do with the resolution of the source picture.
Reference Aspect Ratio ➤ Select Aspect Ratio from the Main Menu to adjust the size, position and scaling method, as needed. Aspect Ratio Scale Mode Fill Screen Justify Center Overscan Scale Mode: To change the aspect ratio (size and shape) of the projected image, press or to highlight Scale Mode and press ENTER or . Use the or button to select the appropriate aspect ratio for the selected screen option and type of program material being viewed; refer to Table 6-1.
Reference Table 6-1. Scale Mode Settings (continued) Aspect Ratio/ Scale Mode Setting Description Letterbox Letterbox mode scales (zooms in on) a 4:3 image linearly (by the same amount on all sides) to fill a 16:9 display, cropping the top and bottom of the image. (This setting has no effect on 16:9 source material.
Reference Table 6-1. Scale Mode Settings (continued) Aspect Ratio/ Scale Mode Setting Aspect Ratio of Source Signal Description Geometry of Projected Image (Note) VW-100HD (16:9 Screen) CW-95HD (2.35:1 Screen) (available with 480i/480p souce material only) 4:3 linearly scales the source active image horizontally and vertically to fill a 4:3 screen.
Reference Table 6-1. Scale Mode Settings (continued) Aspect Ratio/ Scale Mode Setting Aspect Ratio of Source Signal Description Geometry of Projected Image (Note) VW-100HD (16:9 Screen) CW-95HD (2.35:1 Screen) Y 2.35:1 Cinema EL IM IN A R Select Cinema to view 2.35:1 source material in its native aspect ratio. Cinema masks the upper and lower portions of the screen to create a viewable area with a 2.35:1 aspect ratio. The geometry of the active image area is unchanged.
Reference Table 6-1. Scale Mode Settings (continued) Aspect Ratio of Source Signal Description Geometry of Projected Image (Note) VW-100HD (16:9 Screen) CW-95HD (2.35:1 Screen) 1080i HDTV Image 1080i HDTV Image EL IM IN A R Y Aspect Ratio/ Scale Mode Setting 16:9 Select One to One to display the source signal in its native resolution, with no re-sizing or overscan.
Reference Select ISF Memories from the Main Menu to recall, save or delete the contents of the ISF memory slots. For more information about using the ISF memory slots, refer to Using ISF Memories on page 44. ISF Memories Night Day Custom 1 Custom 2 Y ; Save Day Save Custom 1 Save Custom 2 Delete Night Delete Day Delete Custom 1 Delete Custom 2 EL IM IN A R Save Night Night/Day/Custom 1/Custom 2: To manually recall an ISF memory slot, press to highlight Night, Day, Custom 1 or Custom 2.
Reference Memory ➤ The VideoWall/CineWall provides 40 memory locations or slots for storing settings. To manage these stored settings, select Memory from the Main Menu. Note You must enter a passcode to access the Memory menu. Otherwise, it is hidden. To obtain this passcode, contact Runco Technical Support. Memory Recall Y Save Recall EL IM IN A R Delete Recall: In the Recall grid menu, use the arrow keys to navigate through the memories that have something stored in them.
Reference Save: In the Save grid, use the arrow keys to cycle through the available memories. As you navigate through all 40 memories, Save Now will show (Overwrite), as shown here, if the slot already has something in it.
Reference Diagnostics ➤ To see current VideoWall/CineWall status information, select Diagnostics from the Main Menu. Should you ever need to contact Runco Technical Support, this information will help them answer your questions and/or resolve product performance issues. Note You must enter a passcode to access the Diagnostics menu. Otherwise, it is hidden.To obtain this passcode, contact Runco Technical Support.
Reference Test Patterns: The VideoWall/CineWall has numerous internal test patterns that are useful to technicians for advanced calibration, measurement and fault isolation purposes. To access them, select Test Patterns from the Diagnostics menu.
Reference Lamp Ballast: To see current lamp ballast status information, select Lamp Ballast from the Diagnostics menu. Ballast Voltage 89 V Current -or- P/P Ratio 1.75 Temperature 59°C Software Version 1109 13 Y Waveform ID -or- Status EL IM IN A R Hours: To see current system and lamp uptime information, or to reset the current lamp hour counter, select Hours from the Diagnostics menu.
Reference To adjust the lamp, configure the serial communications port and perform numerous other advanced, installation-related tasks, select Advanced Options from the Main Menu. You must enter a passcode to access the Advanced Options menu. Otherwise, it is hidden. To obtain this passcode, contact Runco Technical Support.
Reference • Test Pattern: Refer to Test Patterns on page 109. • Gamma: Gamma changes the colors slightly for Film or Video display. Use Film for deeper reds. Use Video for optimal brightness. • White Boost: White Boost can increase the brightness of the brightest parts of the picture. Set it to Off or High. Using this control may alter slightly some of the brighter colors. Set White Boost to Off before making White Balance or Gray Balance adjustments.
Reference Lamp Settings: Select Lamp Settings from the Advanced Options menu to enable or disable the following settings: • Auto Lamp On: Auto Lamp On makes the lamp turn on soon after AC power is applied. The VideoWall/CineWall must always go through its initialization and sometimes wait for the lamp to cool. • Lamp Saver/Lamp Saver Timeout: Lamp Saver causes the lamp to turn off if there is no source for the specified Lamp Saver Timeout period. When a valid source is re-acquired, the lamp turns on again.
Reference Select Program Information from the Main Menu to see information that uniquely identifies your display: the native resolution, the installed firmware version and the firmware version build date. Should you ever need to contact Runco Technical Support, this information will help them answer your questions or resolve product performance issues. Program Information Runco International 1195 NW Compton Drive Y Beaverton, OR 97006-1992, USA +1.800.237.8626 CineWall 100 EL IM IN A R www.runco.
Reference 6.2 VideoWall/CineWall Specifications Table 6-2 lists the VideoWall/CineWall specifications. Table 6-2. VideoWall/CineWall Specifications Model VW-100HD: 1920 x 1080 (16:9) Model CW-95HD: 1920 x 817 (2.
Reference 6.3 Dimensions Figure 6-3 shows the VideoWall VW-100HD dimensions (all dimensions are in inches). Y 82.45 50.45 WALL CUT OUT SECTION A-A WALL .41 EL IM IN A R 104.00 B 8.00 A A 6.00 54.01 PR 30.71 3.36 1.17 30.73 30.00 26.74 117 88.24 B 16:9 DISPLAY 72.00 VideoWall™/CineWall™ Installer/Integrator Manual 75.63 38.04 92.14 144.00 100.00 88.68 WALL CUT OUT SECTION B-B Figure 6-3.
Reference Figure 6-4 shows the CineWall CW-95HD dimensions (all dimensions are in inches). 82.45 38.50 WALL CUT OUT SECTION A-A A A 88.46 75.63 38.04 94.72 92.14 EL IM IN A R .41 B Y WALL 104.00 8.00 144.00 88.68 WALL CUT OUT SECTION B-B 30.71 42.07 B 6.00 PR 2:35 DISPLAY 15.30 1.17 72.00 30.73 30.00 26.74 Figure 6-4.
Reference 6.4 Supported Timings Table 6-3 lists the signal types supported by each input on the VideoWall/CineWall. Table 6-3. Supported Signal Timings by Input 800x600 Supported? (√ = Yes, – = No) Refresh Rate (Hz) Horizontal Frequency (kHz) Pixel Frequency (MHz) RGB Component HDMI/ DVI Composite S-Video 60.00 31.469 25.175 √ – √ – 72.00 37.861 31.500 √ – √ – 75.00 37.500 31.500 √ – √ – 85.00 43.269 36.000 √ – √ – 56.00 35.156 36.000 √ – √ – 60.00 37.
Reference Table 6-3. Supported Signal Timings by Input (continued) Format Resolution Supported? (√ = Yes, – = No) Refresh Rate (Hz) Horizontal Frequency (kHz) Pixel Frequency (MHz) RGB Component HDMI/ DVI Composite S-Video 1366x768 60.00 50.000 80.000 √ – √ – 1400x1050 1400x1050 60.00 65.317 121.750 √ – √ – 60.00 74.537 161.200 √ – √ – 1600x1200 1600x1200 60.00 75.000 162.000 √ – √ – 50.00 67.521 148.550 √ – √ – 60.00 66.587 138.500 √ – √ – 60.00 67.
SERIAL NUM BER 020-0963-00 Rev. A October 2008 Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.
