User Manual

Dimensions & Installation
OSD Menu
16.8V RUNCAM
01:08
·
·
QUICK SETTINGS
Quick settings:
·
·
Long press UP button for three seconds to access
to the OSD setting‘s screen
·
·
Long press LEFT button for three seconds to
calibrate the voltage. When the voltage text
flashes, press UP/DOWN button to adjust it
·
·
Long press DOWN button for six seconds to reset
OSD settings to default
·
·
Long press RIGHT button for three seconds to
switch between the camera presets
·
·
CLR: clear the ID character;
·
·
ALARM: low voltage warning value, smartly judge
the warning value of the battery when it's low; if set
it manually, then it saves the manual preset value;
·
·
Press the middle button to switch ON / OFF, then
move to POS to enter the position adjustment.
·
·
Sharp View: Turn on, it will increase the image details,
but also noise.
·
·
WIDESCREEN: Dynamic stretching to aspect ratio of
16:9 to match with screen in 16:9,the image center
won't change but the edge will be widened.
RUNCAM_ _ _CLR
OSD Menu
1234567890ABCDEFGHIJ
KLMNOPQRSTUVWXYZ&:=./
ALARM
PILOT
TIMER
VOLTAGE
SHARP VIEW
EXIT
: 14.8V
: ON
: ON
: ON
: ON
WIDESCREEN : OFF
POS
POS
POS
Parameters
SETUP MENU
ENGLISH
YES
·
·
SETUP MENU
·
·
LANGUAGE ( ENGLISH / DEUTSCH / FRANCAIS /
PYCCKNN / PORTUGUES / ESPANOL / 中文 )
·
·
WHITE BAL (ATW / PUSH / USER1 / USER2
/ MANUAL / PUSH LOCK )
·
·
FLIP ( OFF / H-FLIP / V-FLIP / HV-FLIP )
·
·
BRIGHTNESS ( 128/ 0-255 )
Camera Menu
PICT ADJUST
·
·
CONTRAST ( 138 / 0-255 )
·
·
SHARPNESS ( 128 / 0-255 )
·
·
HUE ( 90 / 0-180 )
·
·
COLOR GAIN ( 138 / 0-255 )
FLIP
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
COLOR GAIN
RETURN
OFF
128
138
128
090
138
PICT ADJUST
WHITE BAL
LANGUAGE
CAMERA RESET
EXIT
Model
Image Sensor
Horizontal Resolution
Lens
Screen Format
Signal System
Mirror/Flip
Integrated OSD
One Touch Scene Setting
S/N Ratio
Electronic Shutter Speed
Min. Illumination
WDR
Day/Night
Power
Current
Housing Material
Net Weight
Dimensions
RunCam Racer
Super WDR CMOS Sensor
700TVL
2.1mm(M8) FOV 150°
4:3 / Widescreen (Switchable on OSD menu)
NTSC / PAL
Available
Yes
Personal / Lightrax / Outdoor / Indoor / Cloudy / Twilight
>50dB
Auto
0.01Lux@1.2F
Super WDR
Auto
DC 5-36V
110mA@5V / 40mA@12V
ABS
5.5g
L19mm*W19mm*H18mm
PUSH
M2 Screws
M8 Lens
19mm
19mm
8mm 10mm
18mm
2.Betaflight 3.3 or above setting
USB VCP
Identifier Configuration/MS Serial Rx Telemetry Output Sensor Input Peripherals
UART1
UART2
UART3
UART4
UART5
115200
115200
115200
115200
115200
115200
Disabled AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
RunCam Device
Disabled
Disabled
Disabled
Disabled
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
AUTO
1.Flight controller wiring
Note: Take UART3 for example
Flight controller
TX3 RX3
RX3
TX3
TX
RX
3.Remote control
Mode-1
Connect
Operation
Disconnect
ENTER
LEFT
RIGHT
UP
DOWN
Mode-2
Connect
Operation
Disconnect
ENTER
LEFT
RIGHT
UP
DOWN
When connected, The buzzer on Flight Controller will beep for 3 times; When disconected, The buzzer on Flight Controller
will beep for 2 times only; If connected successfully, you can long press the up button to enter the OSD menu, right button
to switch preset scenes, left button to calibrate voltage and down button to reset OSD.
RunCam Racer
USER MANUAL