Data Sheet

08
194
Explanation of symbols from page 316
Core drills with threaded retainer
For use in magnetic-stand and pillar drilling machines with morse taper retainer. In connection with RUKO arbor
holders no. 108 102 / 108 103 / 108 104 / 108 105 or a threaded retainer such as the Fein KBM 542 / KBM 65.
Handling
• Screwcoredrillintoarborholder.
• Drilltofulldimensionstraightaway.Nocentringorpre-drillingrequired.
• Thebladegeometryofthecoredrillpermitsrapidupwardchipremoval.
• Thespring-loadedejectorpinfacilitatesremovalofthecut-outs.
• Observetableofcuttingspeedsandemployappropriatecoolingagent.
Core drills HSS with Quick IN-shank
For use in magnetic-stand and column drilling machines in connection with Quick IN-adapter
as the Fein KBM 32 Q.
Handling
• Insertejectorpinintocoredrill.
• PushcoredrillintoQuickIn-adapter.
• Drilltofulldimensionstraightaway.Nocentringorpre-drillingrequired.
• Thebladegeometryofthecoredrillpermitsrapidupwardchipremoval.
• Thespring-loadedejectorpinfacilitatesremovalofthecut-outs.
• Observetableofcuttingspeedsandemployappropriatecoolingagent.
Core drills with weldon shank (3/4")
For use in magnetic-stand and pillar drilling machines with morse taper retainer. In connection with RUKO arbor
holders no. 108 302 / 108 303 / 108 315 / 108 316, with RUKO EasyLock no. 108 312 / 108 313 / 108 314 or a
weldon direct shank such as the RUKO magnetic-stand RS5e / RS10 drill.
Handling
• InsertWeldonshankejectorpinintocoredrill.
• Pushcoredrillintoarborandtightenhexagonsocketscrewfirmly.
• Checkproperseatingofcoredrillinarborholder.
• WiththeEasyLockarbor,thecoredrillgetsautomaticallylocked.
• Drilltofulldimensionstraightaway.Nocentringorpre-drillingrequired.
• Thebladegeometryofthecoredrillpermitsrapidupwardchipremoval.
• Thespring-loadedejectorpinfacilitatesremovalofthecut-out.
• Observetableofcuttingspeedsandemployappropriatecoolingagent.
Solid drills with weldon shank (3/4")
For use in magnetic-stand and pillar drilling machines with morse taper retainer. In connection with RUKO arbor
holders no. 108 302 / 108 303 / 108 315 / 108 316, with RUKO EasyLock no. 108 312 / 108 313 / 108 314 or a
weldon direct shank such as the RUKO magnetic-stand RS5e / RS10 drill.
Handling
• PushSolid drill „Solid 3S“ into arbor and tighten hexagon socket screw firmly.
• CheckproperseatingofSolid drill „Solid 3S“ in arbor holder.
• WiththeEasyLockarbor,theSolid drill „Solid 3S“ gets automatically locked.
• Drilltofulldimensionstraightaway.Nocentringorpre-drillingrequired.
•
ThebladegeometryoftheSolid drill „Solid 3S“permitsrapidupwardchipremoval.
• Observetableofcuttingspeedsandemployappropriatecoolingagent.