User's Manual
To cover every corner of a villa, large house or condo, you can buy multiple Reyee Mesh
routers to form a wireless mesh network solution for full-house coverage.
1. Connect the master router (any new one) to the Internet
Please refer to the Scenario 1 for configuration.
2. Put the rest of Reyee routers within 2 meters of the master router and power it on
Wait for 2 to 3 minutes until indicators in each device turn to steady on.
3. Press the Reyee Mesh button on the master router for pai
ring
When the Reyee Mesh indicator of master router blinks, it searches for neighboring
devices. When the Reyee Mesh indicator of the rest of devices blinks, it means that two
routers are being paired. After 2 minutes, the indicators change to steady white, and the
pairing completes.
4. Move the paired devices to the position where the signal needs to be expanded,
and then power it on again
Wait for 3 to 5 minutes until the indicator turns to steady on, the original SSID of
second
ary router(@Reyee-sXXXX) will disappear and the united SSID/password will be
the one you just configured. The connection is successful, whole house mesh Wi-Fi
setting done.
Reyee Mesh Button
This device complies with Industry Canada’s licence‐exempt RSSs. Operation is subject
to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’
appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en
compromettre le fonctionnement.
Exposure Statement：
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS
102 and compliance with RSS‐102 RF exposure, users can obtain Canadian information
on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5
de RSS 102 et la conformité à l'exposition de RSS ‐ 102 rf, utilisateurs peut obtenir
l'information canadienne sur l'exposition et la conformité de rf.
RF Exposure Warning!
This tr
ansmitter must not be co-located or operating in conjunction with any other antenna
or transmitter. This equipment should be installed and operated with a minimum distance
of 20 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co‐placé ou ne fonctionnant en même temps qu'aucune
autre antenne ou émetteur.
Cet équipement devrait être installé et actionné avec une distance minimum de 20
centimètres entre le radiateur et votre corps.
1. Les dispo
sitifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
2.Les produits utilisant la technique d’atténuation DFS (sélection dynamique des fréquences)
sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.
5G Statement：
1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
2.DFS (Dynamic Frequency Selection) products that operate in the bands 5250-5350 MHz,
5470-5600MHz, and 5650-5725MHz.
Scenario 2: Configure more router to form whole family Mesh network
FAQs
Federal Communications Commission Statement
Innovation,Science and Economic Development Canada Statement
●Please properly place the routers and check the signal bar if needed. Do not place two routers too far
away and avoid too many walls or other obstacles.
●If you have 3 or more routers, you can pair them by one-click Reyee Mesh during startup, or repeat the
step 2 to step 4 according to your requirements. At most 5 routers (4+1) can be paired as
recommendation.
①What to do if I forget the management password?
Try the Wi-Fi password which may be the same with the management passwo
rd. If not,
please restore the factory settings.
② How to restore the factory settings?
Power on the router and wait for 2 to 3 minutes until it starts up. Press the Reset button for
more than 3 seconds until the system status indicator blinks. After the indicator changes to
steady on and the SSID “@ Reyee-sXXXX” is broadcast, the router restores the factory
settings successfully.
③Can I connect multiple routers with network cables?
Yes, and wired connection is more stable. Yo
u can connect the WAN port (yellow) from
secondary device with the LAN port (black) from master router for wired connection.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
RF Exposure Warning!
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter.
Caution!
Any changes or modifications not expressly approved by th
e party responsible for
compliance could void the user's authority to operate the equipment.
IMPORTANT!
Operation in the band 5150-5250 MHz is only for indoor use.
RF Exposure Statement:
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment and it also complies with Part 15 of the FCC RF Rules.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.