User's Manual

ManualsBrandsRuijie Networks ManualsComputers & Accessories1800M Wi-Fi 6 Dual-band Mesh Router

③ Place the second router to the specified position and power it on.

Place the second router within 2 meters of the first one, and power it on.

①

②

After t he system status indicator blinks in blue, wait for 2 to 3 minutes until it turns into steady blu e . (I f t he router

had been configured before, please press the Reset Button for more than 3 seconds to restore the factory settings)

Press the Reyee Mesh button on the first router.

Pre s s the Reyee Mesh button on the first router, and its indicator will blink in green during searchin g for routers. The

indicator on the second router w

il l also blink in green slowly during pairing . After 2 minutes, as the indicators on both

routers turn into steady green, the pairing succeeds.

After powerin g the rou ter, wai t for 3 to 5 minutes until the Reyee Mesh indicator turns into steady blue, it is all set and

you can access the Internet. The meshed routers will shar e the same SSID and password. Visit 192.168.110.1 to

check router connecting condi

tion.

If t here is any network port available, you can connect cables as shown below. The wired connection is more stable.

Modem

The Internet speed may be slow if there are multiple paired routers. We recommended mesh-up within 5 routers (1+4) to keep good performance.

Please no te that Wi-Fi s ignal may be we ak if t wo route rs are placed f ar from each o t her or there a re several obst acles li ke wal ls

b etween them.

Internet LAN WAN

Press the Reyee Button

(All devices within 2 meters)

Reyee RG-E3 Wireless Router

User Manual

Scan to Download Reyee Router App

Name Quantity Unit

Router 1 Set

Power Adapter 1 Piece

Warranty Card 1 Copy

User Manual

Copy

Network Cable 1 Piece

Reyee Mesh Indicator

System Status Indicator

Power

LAN 1-4 Ports

WAN Port

Reset Button

Packing List Indicator

Appearance

Scenario 2: Reyee Mesh

Innovation,Science and Economic Development Canada Statement

Please connect the power and network cables as shown below.

ISP Broadband

WAN Port (Yellow)

Reyee Mesh Indicator

System Status Indicator

Network Connection

Access the Internet by App：

Scenario 1: Configure a single router

After you connect the cable and power the router on, it will start up in 2 to 3 minutes. Wait until

the system status indicator turns into steady blue and the router broadcasts the SSID

(

@Reyee-sXXXX by default).

Access the Internet by Web browser：

① Connect to the SSID @Reyee-sXXXX, and the configuration page will be displayed automatically;

if not, please visit 192.168.1

10.1.

@Reyee-sXXXX

xxxxx-xxxxxxxx

Wi-Fi

S/N:GXXXXXXXXXXXX

MAC:XXXX XXXX XXXX

(XXXX refers to the last four digits of MAC on the back of router)

configuration working, you can connect to the

SSID and access to the Internet.

③

The router will match the Internet access

method. Please configure the network

parameters accordingly.

②

Configure the SSID and password. After the

@Reyee-sXXXX

①Download the Reyee Router App

②

③Tap Add Router and follow the guide for configuration

Don’t need to press Reyee Mesh

button on the second router

FAQs

Federal Communications Commission Statement

①

What to do if I forget the management password?

Try the Wi-Fi password which may be the same with the management password. If not, please restore

the factory settings.

②How to restore the factory settings?

Power on the router and wait for 2 to 3 minutes until it starts up.

ress the Reset button for more than 3

seconds until the system status indicator blinks. After the indicator changes to steady on and the SSID

“@ Reyee-sXXXX” is broadcast, the router restores the factory set

tings successfully.

③Can I connect multiple routers with network cables?

Yes, and wired connection is more stable. You can connect the WAN port (yellow) from secondary device

with the LAN port (black) from master router for wired connection.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including inter

ference that may

cause undesired operation.

RF Exposure Statement:

This device complies with FCC radiation exposure limits set forth for an uncontrolled

environment and it also complies with Part 15 of the FCC RF Rules.

RF Exposure Warning!

This equipment must be installed and operated in accordance with provided instructions

and the antenna(s) used for this transmitter must be installed to provide a separation

distance of at least 20 cm from all persons and must not be co-

located or operating in

conjunction with any other antenna or transmitter.

Caution!

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

IMPORTANT!

Operation in the band 5150-5250 MHz is only for indoor use.

This device complies with Industry Canada’s licence‐exempt RSSs. Operation is subject

to the following two conditions:

(1) This device may not cause interference; a

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptib

le d’en compromettre le fonctionnement.

Exposure Statement：

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS

102 and compliance with RSS‐102 RF exposure, users can obtain Canadian information

on RF exposure and compliance.

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5

de RSS 102 et la conformité à l'exposition de RSS ‐ 102 rf, utilisateurs peut obtenir

l'information canadienne sur l'exposition et la conformité de rf.

RF Exposure Warning!

This tr

ansmitter must not be co-located or operating in conjunction with any other antenna

or transmitter. This equipment should be installed and operated with a minimum distance

of 20 centimeters between the radiator and your body.

Cet émetteur ne doit pas être Co‐placé ou ne fonctionnant en même temps qu'aucune

autre antenne ou émetteur.

Cet équipement devrait être installé et actionné avec une distance minimum de 20

centimètres entre le radiateur et votre corps.

5G UNII-1 Statement：

1.The device for operation in the band 5150–5250 MHz is only for indoor use to reduce

the potential for harmful interference to co-channel mobile satellite systems;

2.DFS (Dynamic Frequency Selection) products that operate in the bands 5250-5350 MHz,

5470-5600MHz, and 5650-5725MHz.

1.Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement

pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux;

2.Les produits utilisant la technique d’atténuation DFS (sélection dynamique des fréquences)

sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.

Add Router

The device is being paired.

The device is paired and Wi-Fi signal is normal.

The device is paired but Wi-Fi signal is weak.

Reyee Mesh Indicator

Green

Orange

Blinking

Steady on

The device pairing is disconnected.

Red Steady on

The device is running normally.

Restoring the factory settings or restarting.

System Status Indicator

Blue

Steady on

Blinking

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

—Consult the dealer or an experienced radio/TV technician for help.