BC02 Badge User Guide BC02 Badge User Guide 08/17/2022 (Please read the instruction carefully before installation and use) Nanjing Ruichuangte Information Technology Co.
BC02 Badge User Guide Catalog Warning................................................................................................................................................. 3 FCC Warning.......................................................................................................................................... 4 1． Specification ........................................................................................................................ 6 2． Product introduction .......
BC02 Badge User Guide Warning 1. Do not disassemble, replace or charge the battery in dangerous places. 2. Do not rub the surface of the shell with other objects to prevent static electricity. 3. Do not open the shell in a dangerous place to repair the equipment. 4. The model, specification and other parameters of intrinsically safe products and electronic components related to intrinsically safe circuits shall not be changed at will during maintenance. 5.
BC02 Badge User Guide FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
BC02 Badge User Guide SAR limit set 1.6W/kg. – Body-worn operation; this device was tested for typical body-worn operations with the back of the handset kept 0mm for body worn. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm for body worn. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly.
BC02 Badge User Guide 1． Specification Positioning Mode BLE/GNSS Protocol LoRaWAN Frequency 902.3~914.9MHz Sensitivity -130dBm@SF9, -123dBm@SF8, -115dBm@SF7 17uA@sleep mode Operating Current Max 102mA@20dBm Standby Time 6 months Operating Temperature -15~+45℃ Charging Temperature -10~+40℃ Storage Temperature -40~+85℃ Communication Distance >1.5km in urban area 2． Product introduction 2.
BC02 Badge User Guide five different UUID. Intelligent motion sensor, enter sleep state when stationary, power consumption is less than 17uA. During specified time, such as night, device can enter deep sleep, power consumption is less than 5uA. Intelligent scanning to save power, don’t start BLE scanning if move steps under the threshold. Precise step counting, error is less than 5%.
BC02 Badge User Guide 2.2 Size 2.3 Parameters Type BC02 Frequency 902.3~914.9MHz Tx Power 17dBm +/-2dB Lora Protocol LoRaWAN1.0.3 BLE 2.4G Hz RSSI -92dBm BLE Protocol BLE 4.
BC02 Badge User Guide Sleep Current 17uA Data Interval Configurable, 10s by default Range LoRa: >1000m, BLE: >50m Sensor G-Sensor Upgrade BLE OTA Alarm SOS, hazardous area alarm Temperature -15℃ ~ 60℃ Protection Grade IP66 Size 98mm x 60mm x 7.7~9.1mm（L x W x H） Weight 50g Shell material ABS Installation Rope 3. Operate guide 3.1 Charge The charging port is standard MicroUSB, which is used to charge regular Android phones. When charging, the indicator is blinking red.
BC02 Badge User Guide the platform administrator needs to dismiss SOS by downlink command; otherwise, the green LED keeps flashing. The caller can also restart the device to deactivate the alarm. 3.5 Reboot under startup state, long press the button above three seconds, the LED light will blink three times, and the buzzer will beep, then the device restart. 3.
BC02 Badge User Guide https://location.rctiot.com:8079/guide/ota.html 6．Unpacking and checking 1. Check whether the number, instruction manual, certificate, packing list and accessories of the packing case are complete. 2. The appearance of the product should be intact and marked clearly. 7．Maintenance guide 1. The light does not respond when the device button is pressed？ In this case, the device may be powered off or hibernated in low power state.
