User Guide

ManualsBrandsRugged Ridge ManualsAutomotiveRugged Ridge 11586.01 Textured Black Off-Road Jack Mount for 2007-2018 Jeep Wrangler JK

, Inc.

460 HORIZON DR. SUITE 100 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com

JK Off-Road Jack Mount Bracket

Page 1/4

OMIX-ADA

TECHNICAL SUPPORT

PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: techsupport@omix-ada.com

FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com

1. Jack Mount (2)

2. Upper Mounting Plate (1)

3. Lower Mounting Plate (1)

4. M8 Bolt (4)

5. M8 Washer (12)

6. Spacer (4)

7. M10 Hex Head Bolt (2)

8. M10 Washer (2)

For use with Hard Top:

9. M10 Hex Bolt (2)

10. M8 Spacer (1)

11. M10 Spacer (2)

Components

Part 11586.01

*For use with Rugged Ridge Spartacus Tire Carrier, High Lift Jack Mount Spacer Kit (Part 11586.03) is required*

Summary of content (4 pages)

PAGE 1
Page 1/4 460 HORIZON DR. SUITE 100 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com Part 11586.01 JK Off-Road Jack Mount Bracket 4 5 1 6 2 8 10 3 7 9 11 Components 1. Jack Mount 2. Upper Mounting Plate 3. Lower Mounting Plate 4. M8 Bolt 5. M8 Washer 6. Spacer (2) (1) (1) (4) (12) (4) 7. M10 Hex Head Bolt 8. M10 Washer For use with Hard Top: 9. M10 Hex Bolt 10. M8 Spacer 11.
PAGE 2
Page 2/4 460 HORIZON DR. SUITE 100 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com JK Off-Road Jack Mount Bracket Ensure only one tailgate hinge bolt is removed at a time. This will ensure tailgate remains supported. 1. Remove tailgate hinge covers using a flat head screwdriver on hinge side of cover. Once released, tailgate hinge cover will slide off to left. 2.
PAGE 3
Page 3/4 460 HORIZON DR. SUITE 100 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com JK Off-Road Jack Mount Bracket 4. If installing on a vehicle with a Rugged Ridge tire carrier (A), secure Jack Mount to lower mounting plate’s top two holes using M10 hardware. If using with Hard Top, add M10 spacer between Mounting Plate and Jack Mount. A Rotate Upper Mounting Plate into its horizontal position behind Jack Mount and attach with M8 hardware.
PAGE 4
Page 4/4 460 HORIZON DR. SUITE 100 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com JK Off-Road Jack Mount Bracket TAILGATE HINGE DRILL PATTERN UP Copyright © 2016 Omix-Ada ®, Inc.