User Manual

ManualsBrandsRugged Ridge ManualsAutomotiveRugged Ridge 11542.14 All-Terrain Over-Rider Hoop

, Inc.

460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com

Page 1/8

ALUMINUM XHD & ALL TERRAIN BUMPER SERIES

OMIX-ADA

TECHNICAL SUPPORT

PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: techsupport@omix-ada.com

FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com

Components:

1. Over Rider (11541.14/11542.14)

2. Winch Plate (11541.13)

3. Aluminum XHD Bumper (11541.02)

4. Stubby Ends (11541.10/11542.23)

5. All Terrain Bumper (11542.02)

6. Double X Striker (11542.13)

Read all instructions thoroughly before installation.

WARNING

To avoid serious injury: never exceed 6.5 ton working load on D-Ring mounts.

Use only to assist in vehicle self-recovery; never use D-Ring mounts as a towing

point. Inspect before use. Replce if damaged or distorted. Striker bar is not

to be used for towing or vehicle recovery.

Patent Nos. 7,703,834 & 8,393,656

Summary of content (8 pages)

PAGE 1
Page 1/8 460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com ALUMINUM XHD & ALL TERRAIN BUMPER SERIES Components: 1. 1. Over Rider (11541.14/11542.14) 2. 2. Winch Plate (11541.13) 3. Aluminum XHD Bumper (11541.02) 4. Stubby Ends (11541.10/11542.23) 4. 5. All Terrain Bumper (11542.02) 3. 6. Double X Striker (11542.13) 5. 6. ! WARNING To avoid serious injury: never exceed 6.5 ton working load on D-Ring mounts.
PAGE 2
Page 2/8 460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com ALUMINUM XHD & ALL TERRAIN BUMPER SERIES 3.6L VACUUM PUMP RELOCATION & FRONT BUMPER WINCH PLATE (11541.13) NOTICE: This section applies only to 2012 and newer JK Wranglers. 1. 2. 3. 4. 5. Contents: 6. M6 Nylock Nut 7. Nut plate (2) 8. M10 Flat Washers (2) 9. M10 Hex Bolts (2) Winch Plate M6 Bolt Short (1) M6 Bolt Long (1) L-bracket M6 Flat Washer 1. Remove the factory bumper.
PAGE 3
Page 3/8 460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com ALUMINUM XHD & ALL TERRAIN BUMPER SERIES 4. Rotate vacuum pump. 5. Attach vacuum pump to rear factory stud using hardware removed in step 1. Re-attach air-line and wire harness. 6. Using M6 Long hardware attach L-bracket to vacuum pump. L-bracket should attach at the bottom of vacuum pump bushing. 7. Position winch plate on top of the frame horn. 8.
PAGE 4
Page 4/8 460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com ALUMINUM XHD & ALL TERRAIN BUMPER SERIES Hoop Over rider (11541.14/11542.14) NOTICE: Over rider installs easier with bumper detached from vehicle Contents: 1. Aluminum Hoop Over Rider (1) 2. M6 Hex Bolts (8) 3. M6 Washer (16) 4. M6 Nylock Nuts (8) 1. Remove Aluminum XHD bumper or All Terrain bumper if previously installed. Twist plug at rear of fog light to disconnect wiring.
PAGE 5
Page 5/8 460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com ALUMINUM XHD & ALL TERRAIN BUMPER SERIES Double X Striker (11542.13) 1. Double X Striker (1) 2. M8 Bolt (8) Contents: 3. M8 Washer (16) 4. M8 Lock Nuts (8) 1. Remove Aluminum XHD bumper or All Terrain bumper if previously installed. Twist plug at rear of fog light to disconnect wiring. Slide the bumper off frame. 2. Position Double X Striker on top of center section.
PAGE 6
Page 6/8 460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com ALUMINUM XHD & ALL TERRAIN BUMPER SERIES Aluminum XHD & All Terrain Front Bumper (11541.01/.02 & 11542.01/.02) NOTICE: Some accessories may need to be installed to center section before installing on vehicle 1. 2. 3. 4. 5. Bumper Shell M12x60 Bolt (8) M12 Washer (8) M12 Nut Plate (4) Sheet Metal Screws (8) Contents: 6. M8 Flat Head Bolt (4) 7. M8 Washer (4) 8. M8 Nut (4) 9.
PAGE 7
Page 7/8 460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com ALUMINUM XHD & ALL TERRAIN BUMPER SERIES 4. Fasten d-rings and center section to frame rails using M12 hardware and nut plates. Tighten evenly. Rubber gaskets included with Aluminum XHD mount between d-rings and center section. Note: D-ring holes are spaced wider at top of bracket. 5. Reconnect fog light wiring plug Copyright © 2013 Omix-Ada ®, Inc.
PAGE 8
Page 8/8 460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | info@omix-ada.com ALUMINUM XHD & ALL TERRAIN BUMPER SERIES Stubby Ends (11541.10/11542.23) NOTICE: Bumper should be installed on vehicle prior to stubby end installation 1. Stubby End (2) 2. M12 Hex Bolt (6) 3. M12 Washer (12) Contents: 4. M12 Lock Nut (6) 1. Remove plastic plugs from sides of center section if present. 2. Attach stubby ends to center section using M12 hardware.