INSTRUCTION MANUAL FOR STAINLESS STEEL CALIBERS .44 Magnum; .454 Casull & .480 Ruger RUGER® SUPER REDHAWK DOUBLE-ACTION REVOLVER READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM For Product Service on This Model Please Call: (603) 865-2442 (See p. 19) STURM, RUGER & Company, Inc. Southport, Connecticut 06490 U.S.A.
WHY ARE WE INCLUDING A FIRED CARTRIDGE CASE WITH EVERY RUGER PISTOL AND REVOLVER? Certain states and jurisdictions now require that all newly manufactured pistols and revolvers must be accompanied by a cartridge case, which has been test fired from that gun at the factory. The case must be placed in a sealed container bearing certain information concerning this test cartridge.
FIREARMS SAFETY-YOUR RESPONSIBILITY SAFETY MUST BE THE FIRST AND CONSTANT CONSIDERATION OF EVERY PERSON WHO HANDLES FIREARMS AND AMMUNITION. This Instruction Manual is designed to assist you in learning how to use and care for your RUGER® SUPER REDHAWK revolver properly. Only when you are certain you fully understand the Manual and can properly carry out its instructions should you practice loading, unloading, etc. with live ammunition.
WARNINGS OF GREAT IMPORTANCE ARE FOUND ON THE FOLLOWING PAGES: Locking Devices Alterations Lead Exposure Ammuniton Handling Cylinder Interlock 2 4 6 6 7 8 Firing Disassembly Lubrication Storage Parts Purchasers 10 12 15 16 20 OTHER CAUTIONS AND WARNINGS APPEAR THROUGHOUT THE MANUAL. FIREARMS ARE DANGEROUS WEAPONS– READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL THOROUGHLY AND CAREFULLY BEFORE USING. WARNING–ALTERATIONS This product was designed to function properly in its original condition.
The internal parts are installed either through the top or bottom of the gripframe; therefore, no side plate is needed. The resulting double solid frame contributes greatly to the extraordinary strength and reliability of these revolvers. The massive extended frame and use of Ruger integral scope mounting system on the wide top strap provide a solid scope mounting system. The RUGER® SUPER REDHAWK revolver has a transfer bar which is connected directly to the trigger.
WARNING – LEAD EXPOSURE Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to the state of California to cause birth defects, reproductive harm, and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure. SHOOTING OR CLEANING GUNS MAY EXPOSE YOU TO LEAD AMMUNITION RUGER® SUPER REDHAWK revolvers in caliber .44 magnum will chamber the .44 Rem.
AMMUNITION (CARTRIDGES) NOTICE WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE OR INJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR AS THE RESULT OF, THE USE IN THE SUPER REDHAWK REVOLVER OF FAULTY, OR NON-STANDARD, OR “RE-MANUFACTURED”, OR HAND LOADED (RELOADED) AMMUNITION, OR OF CARTRIDGES OTHER THAN THOSE FOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED. HANDLING CARRYING: The Super Redhawk revolver can be carried with all chambers loaded.
TO LOAD AND FIRE Be sure the revolver is pointed in a safe direction and is never cocked while loading. 1. Press the crane latch and guide cylinder out of frame to the left to its loading position (See Figure 3). FIGURE 3 LOADING THE REVOLVER. 2. Insert cartridges and gently close cylinder, making sure it is securely latched. Do not “flip” the cylinder open or shut.
3. The revolver is now ready to fire, either “double-action” by pulling the trigger through its complete arc for each shot, or “single-action” by cocking the hammer and then pulling the trigger for each shot. The trigger pull is somewhat shorter and lighter when the revolver is fired single action, and this is the preferred mode for precise shots or target shooting 4. DO NOT TOUCH THE TRIGGER UNTIL YOU ARE READY TO FIRE.
WARNING–FIRING When firing the Super Redhawk revolver, be sure all persons are a safe distance to the rear of the shooter. When fired, all revolvers discharge hot gas and particles of lead, powder grains, or lubricant through the clearance gap between the cylinder and the rear of the barrel at high speed. This can injure a person who is standing too close to the revolver.
Practice this important gun handling skill with an unloaded revolver until you have developed the proper control and ‘touch’ to decock your revolver safely. The key to safe decocking is having the weight of the revolver controlled with one hand, while the thumb and forefinger of the ‘shooting hand’ control the hammer and trigger. Improperly restraining the trigger during this procedure may result in the hammer not resting fully against the frame.
NOTE: When ejecting fired cartridge cases, position the revolver at a high angle so the cases will come fully out of the chambers and not slip under the ejector. This high angle positioning is not necessary when ejecting unfired cartridges. CORRECT UNLOADING SEQUENCE 3 1 2 4 WARNING – DISASSEMBLY Always unload a firearm before cleaning, lubrication, disassembly or assembly. Never remove or install a loaded cylinder – it can fire if dropped or struck.
DISASSEMBLY Read instructions before disassembling a gun. 1. BE CERTAIN THE REVOLVER IS UNLOADED BEFORE DISASSEMBLY. 2. Using a properly fitting screwdriver, remove grip screw. Remove pistol grip inserts from grips. Grip panel locator may then be removed. Pull grip downward off frame. Take care not to lose the disassembly pin, which may fall free when the grip is removed (See Figure 5). 3. Cock the hammer.
NOTE: If you cannot supply sufficient force to the plunger using the mainspring assembly as a “tool”, then use a screwdriver of appropriate size and insert through hole in frame. It may be necessary to slightly depress the trigger while removing the trigger guard assembly. 7. Cradle the revolver frame in your left hand and with the thumb of your right hand press cylinder latch button, swing out cylinder assembly and remove it forward from the frame. 8.
CARE AND CLEANING ALWAYS BE CERTAIN THE REVOLVER IS UNLOADED BEFORE CLEANING. The internal mechanism of the Super Redhawk revolver can be lubricated without disassembly. A few drops of light oil recommended as suitable for firearms, applied periodically about the various frame openings, will work its way into the mechanism parts. The exterior of the revolver and the bore and chambers should be thoroughly cleaned and then wiped with an oily cloth if the gun is to be stored. Do not apply excess lubrication.
STORAGE GUNS SHOULD NOT BE STORED LOADED! USE THE LOCKING DEVICE SUPPLIED WITH THE REVOLVER FOR STORAGE. (SEE PAGE 2) Do not keep your revolver in a leather, fabric or canvas holster when it is stored. These materials attract moisture, even though the holster may appear to be perfectly dry. TO RENDER THE REVOLVER INOPERATIVE FOR SAFE STORAGE With the muzzle pointed in a safe direction, press the cylinder latch and swing the cylinder outward.
disassembly pin from the mainspring strut. Lower the hammer and replace the grips on the revolver. The revolver is now reassembled and can be loaded and fired normally. While the revolver is less likely to be used by unauthorized persons when disassembled in the above manner, it is always safest to store a firearm with the supplied locking device correctly installed, or to store the firearm in a gun safe or other secure location, away from children and unauthorized adults.
3. Disassemble the other ring and install it on the forward section of the scope tube with the lug forwardly also. Install the four top screws. Again, do not tighten. 4. Assemble the rings to the frame with the lugs engaging the recesses in the top surface of the receiver. Tighten the clamp nuts so that the rings are locked to the semi-circular cuts on the sides of the frame. 5. Rotate the scope until cross-hairs are aligned properly, and slide the scope to desired eye relief.
SERVICE AND PARTS POLICY If you have any questions with regard to the performance of your RUGER® SUPER REDHAWK revolver please write or call (603-865-2442) our Product Service Department in Newport, New Hampshire 03773, fully describing all circumstances and conditions involved.
WARNING –PARTS PURCHASERS It is the purchaser’s responsibility to be absolutely certain that any parts ordered from the factory are correctly fitted and installed. Firearms are complicated mechanisms and IMPROPER FITTING OF PARTS MAY RESULT IN A DANGEROUS MALFUNCTION, DAMAGE TO THE FIREARM, AND SERIOUS INJURY TO THE SHOOTER AND OTHER PERSONS. The purchaser and installer of parts must accept full responsibility for the correct adjustment and functioning of the revolver after such installation.
RUGER® SUPER REDHAWK PARTS LIST Design, prices and specifications subject to change without notice. SPECIFY MODEL AND CALIBER WHEN ORDERING (See Exploded View on Page 25.
* * * * * * 22 * * Part Name Cylinder Assembly, Non-fluted Cylinder Latch Cylinder Latch Pivot Cylinder Latch Plunger Cylinder Latch Spring Cylinder Latch Spring Cylinder Retaining Ball, (2 Req’d.) Disassembly Pin Ejector Ejector Ejector Ejector Alignment Pins, (2 Req’d.
Part Name Front Sight Front Sight Plunger Front Sight Plunger Spring Grip Panel Ferrule, (Right) Grip Panel Ferrule, (Left) Grip Panel Inserts, Wood (Sold in Pairs Only) Grip Panel Inserts, Wood (Sold in Pairs Only) Grip Panel Locator Grip Panel Screw Grip, 1 Piece Rubber, No Inserts Grip, 1 Piece Rubber with Wood Inserts Grip, 1 Piece Rubber with Wood Inserts * Hammer Assembly * Hammer Assembly, Tumble Gray * Hammer Dog Hammer Dog Pivot Pin Hammer Dog Plunger Hammer Dog Spring Hammer Pivot Assembly Ham
* 24 * * * Part Name Rear Sight Base Assembly Rear Sight Blade, High, White Outline Notch Rear Sight Blade, Low, White Outline Notch Rear Sight Pivot Pin Rear Sight Elevation Screw Rear Sight Elevation Spring, (2 Req’d.
EXPLODED VIEW SUPER REDHAWK
SUPER REDHAWK REVOLVER MECHANISM
THE BASIC RULES OF SAFE FIREARMS HANDLING We believe that Americans have a right to purchase and use firearms for lawful purposes. The private ownership of firearms in America is traditional, but that ownership imposes the responsibility on the gun owner to use his firearms in a way which will ensure his own safety and that of others. When firearms are used in a safe and responsible manner, they are a great source of pleasure and satisfaction, and represent a fundamental part of our personal liberty.
A safe direction must take into account the fact that a bullet may penetrate a wall, ceiling, floor, window, etc., and strike a person or damage property. Make it a habit to know exactly where the muzzle of your gun is pointing whenever you handle it, and be sure that you are always in control of the direction in which the muzzle is pointing, even if you fall or stumble. Keep your finger off the trigger until you are ready to shoot. 3. FIREARMS SHOULD BE UNLOADED WHEN NOT IN USE.
5. BE SURE OF YOUR TARGET BEFORE YOU SHOOT. Don’t shoot unless you know exactly where your bullet is going to strike. Be sure of the bullet stop behind your target, even when dry-firing with an unloaded gun. If you are in the field hunting, do not fire at a movement or noise. Take the time to be absolutely certain of your target before you pull the trigger. 6. WEAR SHOOTING GLASSES AND HEARING PROTECTORS WHEN YOU SHOOT.
8. DON’T SHOOT AT A HARD SURFACE, OR AT WATER. Bullets can glance off many surfaces like rocks or the surface of water and travel in unpredictable directions with considerable velocity. 9. NEVER TRANSPORT A LOADED FIREARM. Firearms should always be unloaded before being placed in a vehicle. A suitable carrying case or scabbard should by used to carry an unloaded firearm to and from the shooting area. 10. AVOID ALCOHOLIC BEVERAGES WHEN SHOOTING. Don’t drink until the day’s shooting is over.
A BRIEF ACCOUNT OF AN EXTRAORDINARY ACHIEVEMENT: RUGER FIREARMS One of the few American firearms manufacturers whose management has remained unchanged since starting in business, Sturm, Ruger & Company, Inc., had its beginning in a small machine shop occupying a rented frame building in Southport, Connecticut. In January, 1949, with an initial investment of only $50,000 and an idea, William B. Ruger and Alexander M. Sturm started production of a .
WHY NO WARRANTY CARD HAS BEEN PACKED WITH THIS NEW RUGER FIREARM The Magnuson-Moss Act (Public Law 93-637) does not require any seller or manufacturer of a consumer product to give a written warranty. It does provide that if a written warranty is given, it must be designated as “limited” or as “full” and sets minimum standards for a “full” warranty. Sturm, Ruger & Company, Inc.
